Solar energy use for energy savings in dairy processing plants

New Zealand is one of the world’s largest producers of dairy products and has a climate with high levels of solar radiation; however, the use of solar energy in the dairy processing industry has received limited attention. An examination of historical records found that the annual peak in New Zealand milk production and processing occurs at a time when solar radiation levels are increasing markedly. An F-Chart analysis was used to simulate the performance of large-area arrays of solar collectors and to determine their suitability for heating and cooling in a dairy processing environment. For the study four types of solar collectors were analysed: glazed flat plates, evacuated tubes, evacuated tubes with CPC reflectors and a building-integrated solar collector under development at the University of Waikato (UoW). It was found that of these echnologies, both flat plate and evacuated tubes with CPC reflectors could make useful heating and cooling contributions. Furthermore, the solar fraction was determined mainly by the collector area to storage volume ratio. Finally, it was found that the UoW building-integrated solar collector could make a significant contribution to energy use in dairies and may be an attractive future technology for the industry.

Composite crashworthy structures

This study presents an innovative finite element delamination model which successfully reproduced the experimental failure behaviour observed in axial crush testing. Tests were conducted on tubes manufactured by a novel composite curing process, resulting in the ability to cure tubular profiles in 7 minutes - 95% quicker than traditional autoclave curing.

Using omeprazole to link the components of the post-prandial alkaline tide in the spiny dogfish, Squalus acanthias

After a meal, dogfish exhibit a metabolic alkalosis in the bloodstream and a marked excretion of basic equivalents across the gills to the external seawater. We used the H⁺, K⁺-ATPase pump inhibitor omeprazole to determine whether these post-prandial alkaline tide events were linked to secretion of H⁺ (accompanied by Cl^–) in the stomach. Sharks were fitted with indwelling stomach tubes for pretreatment with omeprazole (five doses of 5mg omeprazole per kilogram over 48 h) or comparable volumes of vehicle (saline containing 2% DMSO) and for sampling of gastric chyme. Fish were then fed an involuntary meal by means of the stomach tube consisting of minced flatfish muscle (2% of body mass) suspended in saline (4% of body mass total volume). Omeprazole pretreatment delayed the post-prandial acidification of the gastric chyme, slowed the rise in Cl^– concentration of the chyme and altered the patterns of other ions, indicating inhibition of H⁺ and accompanying Cl^– secretion. Omeprazole also greatly attenuated the rise in arterial pH and bicarbonate concentrations and reduced the net excretion of basic equivalents to the water by 56% over 48h. Arterial blood CO₂ pressure and plasma ions were not substantially altered. These results indicate that elevated gastric H⁺ secretion (as HCl) in the digestive process is the major cause of the systemic metabolic alkalosis and the accompanying rise in base excretion across the gills that constitute the alkaline tide in the dogfish.

Crash investigation of side intrusion beam during high and low pressure tube hydroforming

Advanced high strength steels (AHSS), in particular, are an attractive group materials, offering higher strength for improved energy absorption and the opportunity to reduce weight through the use of thinner gauges. High pressure tube hydroforming (HPTH) has been used to produce safety components for these steels, but it is expensive. Low pressure tube hydroforming (LPTH) is a lower cost alternative to form the safety components in the car. The side intrusion beam is the second most critical part after front rail in the car structure for passenger safety during crash. The forming as well as crash behaviour of a square side intrusion beam from both processes was investigated using numerical simulation. This paper investigated the interaction between the forming and crash response of these materials in order to evaluate their potential for use in vehicle design for crashworthiness. The energy absorption characteristics of the different tubes were calculated and the results from the numerical analyses compared for both hydroforming process.

Protein electrochemistry using aligned carbon nanotube arrays

The remarkable electrocatalytic properties and small size of carbon nanotubes make them ideal for achieving direct electron transfer to proteins, important in understanding their redox properties and in the development of biosensors. Here, we report shortened SWNTs can be aligned normal to an electrode by self-assembly and act as molecular wires to allow electrical communication between the underlying electrode and redox proteins covalently attached to the ends of the SWNTs, in this case, microperoxidase MP-11. The efficiency of the electron transfer through the SWNTs is demonstrated by electrodes modified with tubes cut to different lengths having the same electron-transfer rate constant.

The male germ unit of Rhododendron : quantitative cytology, three-dimensional reconstruction, isolation and detection using fluorescent probes

The sperm cells of Rhododendron laetum and R. macgregoriae differentiate within the pollen tube about 24 h after germination in vitro. Threedimensional reconstruction shows that the sperm cells are paired together, and both have extensions that link with the tube nucleus, forming a male germ unit. Quantitative analysis shows that the sperm cells in each pair differ significantly in surface area, but not in cell volume nor in numbers of mitochondria or plastids. When isolated from pollen tubes by osmotic shock, the sperm cells became ellipsoidal and surrounded by their own plasma membrane, while a proportion remained in pairs linked by the inner tube plasma membrane. Both generative and sperm cells are visualized in pollen tube preparations by immunofluorescence with anti-tubulin and anti-actin monoclonal antibodies (MAbs) combined with H33258 fluorescence of the nuclei. Video-image processing shows the presence of an axial microtubule cage in the generative cells, and some microtubules are present in the cytoplasmic extensions that clasp the tube nucleus. Following sperm cell division, the extensive phragmoplast between the sperm nuclei is partitioned by the plasma membranes.

Localisation of allergens in ryegrass pollen and in airborne micronic particles

In Melbourne, Australia, grass pollen allergens, especially from ryegrass, are a major cause of allergic hayfever and asthma. This review outlines recent developments in our understanding of how grass pollen allergens find their way into the atmosphere and how they are transported in particulate form. Much of this work has relied on antibody technology in immunological and immunocytochemical investigations. The localisation of allergens in situ has proved difficult due to their water-soluble character. Recently, allergens have been localised in developing ryegrass pollen by dryfixation, rapid-freeze and freeze-substitution techniques. This involved anthers being substituted in a mixture of aldehydes, organic solvents, and 2,2-dimethoxypropane. Incubation in dimethylsulfoxide prior to embedding in LR Gold resin provided good infiltration with freeze-substituted material. Immunogold-labelled sections show that the major allergens, Lol p 1 and Lol p 5, are synthesised in the pollen cytoplasm from the early bicellular stage, soon after the first starch granules are formed. From the early tricellular stage, Lol p 5 moves into the starch granules where it remains until maturity. Lol p 1 is localised in the cytoplasm of mature pollen grains. The incidence of airborne grass pollen, as measured in pollen traps, correlates with hayfever symptoms. Forecasting models which rely on rainfall and temperature data have been produced for the grass pollen (daily and seasonal) counts in Melbourne. Research over the past six years has shed light on the causes of grass-pollen-induced asthma. Micronic particles in the atmosphere may be starch granules originating from pollen grains osmotically ruptured by rainwater. Ultrastructural and immunological characterisation of micronic particles collected from outdoor air filters confirm the presence of airborne starch granules. These are loaded with grass pollen allergens, occur in the atmosphere especially after rainfall, and correlate significantly with instances of allergic asthma. Diesel particles might also play a role in the transmission of grass pollen allergens and thus become an extra asthma trigger. A variation in the mode of release of micronic particles occurs in other species, such as birch, where such particles are derived from burst birch pollen tubes. These particles are positive for Bet v 1 and are starch granules which are released into the atmosphere after light rain as a result of pollen germination on, e.g., leaves. After subsequent rupture of pollen tubes their contents are released when conditions become drier.

Isolation of sperms from the pollen tube of flowering plants during fertilization

Sperm cells have been isolated from pollen tubes growing in style segments of the dicotlyledon Rhododendron macgregoriae and the monocotyledon Gladiolus gandavensis by the in vivo/in vitro method at various stages of fertilization. Pollen tubes emerged from the cut end of the style into agar medium, and more than 95% contained sperm cells. Sperm cells were released from the pollen tubes by osmotic shock or by placing styles in wall-degrading enzymes: 0.5% macerozyme and 1% cellulase. The isolated sperms were ellipsoidal protoplasts of diameter about 2 × 3 micrometers in Gladiolus and about 3 × 4 micrometers in Rhododendron. After isolation, a proportion of the sperm cells occurred in pairs linked at one end by finger-like connections. The pairs of isolated sperms were dimorphic in terms of surface area and volume. By cutting the styles at various positions and times after pollination, the potential exists to detect changes in sperm gene expression associated with fertilization.

Source of Bet v 1 loaded inhalable particles from birch revealed

Allergenic proteins present in pollen grains, when inhaled, interact with the airways to cause an attack of asthma in susceptible humans. In one system, grass pollen grains rupture osmotically in rainfall, releasing allergen-containing inhalable particles into the atmosphere. In contrast, birch tree pollen grains do not rupture under these conditions, yet the major allergen, Bet v 1, has been detected in the atmosphere in inhalable particles of unknown origin. It is possible that Bet v 1 may diffuse from intact settled pollen grains and the allergenic material may again become airborne, interacting with settled fine particles from other sources prior to resuspension. This study investigates the mechanism for the release of birch pollen allergen-containing inhalable particles from pollen grains. We propose the hypothesis that (1) airborne birch pollen grains settle on nearby leaf surfaces; (2) then, following light rainfall, the grains germinate and, (3) later, pollen tubes burst, releasing inhalable particles carrying Bet v 1 into the atmospheric aerosol.   We used microscopic analyses of pollen behaviour following anther opening, a Burkard volumetric trap for pollen counts and a high volume air sampler with a two-stage cascade impactor for quantitative immunochemical analyses of Bet v 1. On dry days of high birch pollen count (48 grains/m3, 1.5 ng/m3 of Bet v 1), we found that the surfaces of birch leaves became coated with pollen. This ”pollen rain” is a source of secondary emission of allergens into the atmosphere. We observed that following light rainfall (<1 mm per day), about 80% of the birch pollen grains germinated, producing pollen tubes, especially in the sticky surface secretions of leaf glands. These pollen tubes may grow up to 300 μm in length prior to rupturing, each releasing about 400 starch granules coated with allergen molecules that may, after drying, be dispersed into the aerosol. On these days following light rainfall, the highest atmospheric levels of Bet v 1 (1.18 ng/m3) are associated with inhalable particles. Following heavy rainfall, both pollen and inhalable particles are washed from the atmosphere. Immunoprinting studies show that Bet v 1 is associated with starch granules rather than the smaller orbicules. Bet v 1 is present in the atmosphere in large particles, i.e. in particular pollen grains and in inhalable particles, i.e. in particular starch granules.

The impact of column connection on band broadening in very high pressure liquid chromatography

A series of experiments was conducted to evaluate the degree of band broadening in very high pressure LC due to column connections. Different column manufacturers use slightly different designs for their column fittings. If the same column connections are repeatedly used to attach columns of different origins, different void volumes form between capillary tubes and column inlets. An Agilent Ultra Low Dispersion Kit (tubing id 75 μm) was installed on an Agilent Infinity 1290 ultra HPLC and used to connect successively an Agilent, a Phenomenex, and a Waters column. A series of uracil (unretained) samples were injected and eluted at a wide range of flow rates with a water/acetonitrile mixture as eluent. In order to determine the variance contribution from column connections as accurately as possible a nonretained probe compound was selected because the variance contribution from the column is the smallest for analytes, which have very low k values. Yet, this effect still has an impact on the resolution for moderately retained compounds (k > 2) for narrow-bore columns packed with fine particles, since variance contributions are additive for linear chromatographic systems. Each injection was replicated five times under the same experimental conditions. Then NanoViper column connections (tubing id 75 μm) were used and the same injections were made. This system was designed to minimize connection void volumes for any column. Band variances were calculated as the second central moment of elution peaks and used to assess the degree of band broadening due to the column connections. Band broadening may increase from 3.8 to 53.9% when conventional metal ferrules were used to join columns to connection sites. The results show that the variance contribution from improper connections can generate as much as 60.5% of the total variance observed. This demonstrates that column connections can play a larger role than the column packing with respect to band dispersion.

Geometry of compensatory feeding and water consumption in Drosophila melanogaster

Feeding behaviour is an expression of an animal’s underlying nutritional strategy. The study of feeding decisions can hence delineate nutritional strategies. Studies of Drosophila melanogaster feeding behaviour have yielded conflicting accounts, and little is known about how nutrients affect feeding patterns in this important model species. Here, we conducted two experiments to characterize nutrient prioritization and regulation. In a choice experiment, we allowed female flies to self-regulate their intake of yeast, sucrose and water by supplying individual flies with three microcapillary tubes: one containing only yeast of varying concentrations, another with just sucrose of varying concentrations, and the last with just water. Flies tightly regulated yeast and sucrose to a constant ratio at the expense of excess water intake, indicating that flies prioritize macronutrient regulation over excess water consumption. To determine the relative importance of yeast and sucrose, in a no-choice experiment, we provided flies with two microcapillary tubes: the first with one of the 28 diets varying in yeast and sucrose content and the other with only water. Flies increased total water intake in relation to yeast consumption but not sucrose consumption. Additionally, flies increased diet intake as diet concentration decreased and as the ratio of sugar to yeast equalized. Using a geometric scaling approach, we found that the patterns of diet intake can be explained by flies prioritizing protein and carbohydrates equally and by the lack of substitutability between the nutrients. We conclude by illustrating how our results harmonize conflicting results in the literature once viewed in a two-dimensional diet landscape.

Automotive engineering metal foam structures: fabrication, characterisation, testing and simulation

The contrubution of this thesis is to generate fundamental research and design information on the impact and bending behaviours of metal foams and foam-filled tubes

Carbon nanotube based elastomer composites-an approach towards multifunctional materials

The current study focuses on giving a basic understanding of tubular graphene sheets or carbon nanotubes (CNTs) and points towards their role in fabricating elastomer composites. Since the properties and the performance of CNT reinforced elastomer composites predominantly depend on the rate of dispersion of fillers in the matrix, the physical and chemical interaction of polymer chains with the nanotubes, crosslinking chemistry of rubbers and the orientation of the tubes within the matrix, here, a thorough study of these topics is carried out. For this, various techniques of composite manufacturing such as pulverization, heterocoagulation, freeze drying, etc. are discussed by emphasizing the dispersion and alignment of CNTs in elastomers. The importance of the functionalization technique as well as the confinement effect of nanotubes in elastomer media is derived. In a word, this article is aimed exclusively at addressing the prevailing problems related to the CNT dispersion in various rubber matrices, the solutions to produce advanced high-performance elastomeric composites and various fields of applications of such composites, especially electronics. Special attention has also been given to the non-linear viscoelasticity effects of elastomers such as the Payne effect, Mullin's effect and hysteresis in regulating the composite properties. Moreover, the current challenges and opportunities for efficiently translating the extraordinary electrical properties of CNTs to rubbery matrices are also dealt with.

Real-time measurement of phloem turgor pressure in Hevea brasiliensis with a modified cell pressure probe

Background: Although the pressure flow theory is widely accepted for the transport of photoassimilates in phloem sieve elements, it still requires strong experimental validation. One reason for that is the lack of a precise method for measuring the real-time phloem turgor pressure from the sink tissues, especially in tree trunks. Results: Taking the merits of Hevea brasiliensis, a novel phloem turgor pressure probe based on the state of the art cell pressure probe was developed. Our field measurements showed that the phloem turgor pressure probe can sensitively measure the real-time variation of phloem turgor pressure in H. brasiliensis but the calculation of phloem turgor pressure with xylem tension, xylem sap osmotic potential and phloem sap osmotic potential will under-estimate it. The measured phloem turgor pressure gradient in H. brasiliensis is contrary to the Münch theory. The phloem turgor pressure of H. brasiliensis varied from 8-12 bar as a consequence of water withdrawal from transpiration. Tapping could result in a sharp decrease of phloem turgor pressure followed by a recovery from 8-45 min after the tapping. The recovery of phloem turgor pressure after tapping and its change with xylem sap flow suggest the importance of phloem water relationship in the phloem turgor pressure regulation. Conclusion: The phloem turgor pressure probe is a reliable technique for measuring the real-time variation of phloem turgor pressures in H. brasiliensis. The technique could probably be extended to the accurate measurement of phloem turgor pressure in other woody plants which is essential to test the Münch theory and to investigate the phloem water relationship and turgor pressure regulation. © 2014 An et al.