Electrospun spinel LiNi0.5Mn1.5O4 hierarchical nanofibers as 5 v cathode materials for lithium-ion batteries

Spinel LiNi0.5Mn1.5O4 hierarchical nanofibers with diameters of 200–500 nm and lengths of up to several tens of micrometers were synthesized using low-cost starting materials by electrospinning combined with annealing. Well-separated nanofiber precursors impede the growth and agglomeration of Li-Ni0.5Mn1.5O4 particles. The hierarchical nanofibers were constructed from attached LiNi0.5Mn1.5O4 nanooctahedrons with sizes ranging from 200 to 400 nm. It is proven that these Li-Ni0.5Mn1.5O4 hierarchical nanofibers exhibit a favorable electrochemical performance. At a 0.5C (coulombic) rate, it shows an initial discharge capacity of 133 mAhg_1 with a capacity retention over 94% after 30 cycles. Even at 2, 5, 10, and 15C rates, it can still deliver a discharge capacity of 115, 100, 90, and 80 mAhg_1, respectively. Compared with self-aggregated nanooctahedrons synthesized using common sol–gel methods, the LiNi0.5Mn1.5O4 hierarchical nanofibers exhibit a much higher capacity. This is owing to the fact that the self-aggregation of the unique nanooctahedron-in-nanofiber structure has been greatly reduced because of the attachment of nanopolyhedrons in the long nanofibers. This unique microstructured cathode results in the large effective contact areas of the active materials, conductive additives and fully realize the advantage of nanomaterial-based cathodes.

Effects of mechanical deformation on electric performance of rechargeable batteries embedded in load carrying composite structures

Integrating rechargeable battery cells with fibre reinforced polymer matrix composites is a promising technology to enable composite structures to concurrently carry load and store electric energy, thus significantly reducing weight at the system level. To develop a design criterion for structural battery composites, rechargeable lithium polymer battery cells were embedded into carbon fibre/epoxy matrix composite laminates, which were then subjected to tensile, flexural and compressive loading. The electric charging/discharging properties were measured at varying levels of applied loads. The results showed that degradation in battery performance, such as voltagea and energy storage capacity, correlated well with the applied strain under three different loading conditions. Under compressive loading, battery cells, due to their multilayer construction, were unable to prevent buckling of composite face sheets due to the low lateral stiffness, leading to lower compressive strength that sandwich panels with foam core.

Stable anode performance of an Sb–carbon nanocomposite in lithium-ion batteries and the effect of ball milling mode in the course of its preparation

Materials that alloy with lithium (Si, Ge, Sn, Sb, and P) are considered as alternatives to graphitic anodes in lithium-ion batteries. Their practical use is precluded by large volume changes (200–370%) during cycling. Embedding nanoparticles into carbon is being investigated as a way to tackle that, and ball milling is emerging as a technique to prepare nanocomposites with enhanced capacity and cyclic stability. Using Sb as a model system, we investigate the preparation of Sb–carbon nanocomposites using a reconfigurable ball mill. Four distinctive milling modes are compared. The structure of the composites varies depending on the mode. Frequent strong ball impacts are required for the optimal electrochemical performance of the nanocomposite. An outstanding stable capacity of 550 mA h g−1 for 250 cycles at a current rate of 230 mA g−1 is demonstrated in a thin electrode (1 mg cm−2) and a capacity of [similar]400 mA h g−1 can be retained at 1.15 A g−1. Some capacity fade is observed in a thicker electrode (2.5 mg cm−2), i.e. the performance is sensitive to mass loading. The electrochemical stability originates from the nanocomposite structure containing Sb nanoparticles (5–15 nm) dispersed in a carbon component.

Electrochemical investigation of sodium reactivity with nanostructured Co3O4 for sodium-ion batteries

The electrochemical behaviour of Co3O4 with sodium is reported here. Upon cycling in the voltage window of 0.01–3.0 V, Co3O4 undergoes a conversion reaction and exhibits a reversible capacity of 447 mA h g−1 after 50 cycles. Therefore, nanostructured Co3O4 presents feasible electrochemical sodium storage, offering possibilities to develop new anode materials for sodium-ion batteries.

Dye-sensitised solar cell with nickel cathode

The present invention relates to a cathode for use in a dye-sensitised solar cell which comprises a redox couple, wherein the cathode comprises: (a) metallic nickel; and (b) intrinsically conducting polymer that, during operation of the cell, reduces an oxidised species of the redox couple.

Empowering the smart grid : can redox batteries be matched to renewable energy systems for energy storage?

The charging of an undivided cerium–zinc redox battery by various current waveforms some of which mimic the output of renewable energy (solar, wind, tidal, biofuel burning) to electricity transducers is considered in this work, where the battery operates through diffusion-only conditions, and is discharged galvanostatically. Under reasonable assumption, the mathematical model developed enables the observation that the performance characteristic of the cells charged with a constant power input differentiates between the various current–charge waveforms, with cell geometry and electrode kinetics playing subtle, but significant, roles; in particular, high efficiency is observed for sunlight-charged batteries which are thin and suffer no corrosion of the sacrificial electrode, and which have already experienced a charge–discharge cycle. The performance characteristics of the systems are interpreted in the light of consequences for smart grid realisation, and indicate that, for a constant power input, the most matched renewable is biofuel burning with a current output that linearly increases with time.

An organic ionic plastic crystal electrolyte for rate capability and stability of ambient temperature lithium batteries

Reliable, safe and high performance solid electrolytes are a critical step in the advancement of high energy density secondary batteries. In the present work we demonstrate a novel solid electrolyte based on the organic ionic plastic crystal (OIPC) triisobutyl(methyl)phosphonium bis(fluorosulfonyl)imide (P1444FSI). With the addition of 4 mol% LiFSI, the OIPC shows a high conductivity of 0.26 mS cm-1 at 22 °C. The ion transport mechanisms have been rationalized by compiling thermal phase behaviour and crystal structure information obtained by variable temperature synchrotron X-ray diffraction. With a large electrochemical window (ca. 6 V) and importantly, the formation of a stable and highly conductive solid electrolyte interphase (SEI), we were able to cycle lithium cells (LiLiFePO4) at 30 °C and 20 °C at rates of up to 1 C with good capacity retention. At the 0.1 C rate, about 160 mA h g-1 discharge capacity was achieved at 20 °C, which is the highest for OIPC based cells to date. It is anticipated that these small phosphonium cation and [FSI] anion based OIPCs will show increasing significance in the field of solid electrolytes.

Ionic liquid electrolytes as a platform for rechargeable metal–air batteries: a perspective

Metal-air batteries are a well-established technology that can offer high energy densities, low cost and environmental responsibility. Despite these favourable characteristics and utilisation of oxygen as the cathode reactant, these devices have been limited to primary applications, due to a number of problems that occur when the cell is recharged, including electrolyte loss and poor efficiency. Overcoming these obstacles is essential to creating a rechargeable metal-air battery that can be utilised for efficiently capturing renewable energy. Despite the first metal-air battery being created over 100 years ago, the emergence of reactive metals such as lithium has reinvigorated interest in this field. However the reactivity of some of these metals has generated a number of different philosophies regarding the electrolyte of the metal-air battery. Whilst much is already known about the anode and cathode processes in aqueous and organic electrolytes, the shortcomings of these electrolytes (i.e. volatility, instability, flammability etc.) have led some of the metal-air battery community to study room temperature ionic liquids (RTILs) as non-volatile, highly stable electrolytes that have the potential to support rechargeable metal-air battery processes. In this perspective, we discuss how some of these initial studies have demonstrated the capabilities of RTILs as metal-air battery electrolytes. We will also show that much of the long-held mechanistic knowledge of the oxygen electrode processes might not be applicable in RTIL based electrolytes, allowing for creative new solutions to the traditional irreversibility of the oxygen reduction reaction. Our understanding of key factors such as the effect of catalyst chemistry and surface structure, proton activity and interfacial reactions is still in its infancy in these novel electrolytes. In this perspective we highlight the key areas that need the attention of electrochemists and battery engineers, in order to progress the understanding of the physical and electrochemical processes in RTILs as electrolytes for the various forms of rechargeable metal-air batteries.

Biotemplated fabrication of a novel hierarchical porous C/LiFePO4/C composite for Li-ion batteries

Hierarchical porous composites are a potentially attractive material for high-rate cathode. This work presents a facile sol-gel process for the fabrication of a hierarchical porous C/LiFePO4/bio-C composite by using artemia cyst shells as natural biological carbon templates. The C/LiFePO4/bio-C composite exhibits a superior electrochemical performance with discharge capacities of 105 mA h g-1, 93 mA h g-1 and 80 mA h g-1 at 5 C, 10 C and 20 C, respectively. Remarkably, it produces a high discharge capacity of 69.1 mA h g-1 and no fading after 50 cycles even at a high current density of 6800 mA g-1. This journal is

Determining the sensitivity of the Antarctic amphipod Orchomenella pinguides to metals using a joint model of survival response to exposure concentration and duration

Developing water quality guidelines for Antarctic marine environments requires understanding the sensitivity of local biota to contaminant exposure. Antarctic invertebrates have shown slower contaminant responses in previous experiments compared to temperate and tropical species in standard toxicity tests. Consequently, test methods which take into account environmental conditions and biological characteristics of cold climate species need to be developed. This study investigated the effects of five metals on the survival of a common Antarctic amphipod, Orchomenella pinguides. Multiple observations assessing mortality to metal exposure were made over the 30 days exposure period. Traditional toxicity tests with quantal data sets are analysed using methods such as maximum likelihood regression (probit analysis) and Spearman–Kärber which treat individual time period endpoints independently. A new statistical model was developed to integrate the time-series concentration–response data obtained in this study. Grouped survival data were modelled using a generalized additive mixed model (GAMM) which incorporates all the data obtained from multiple observation times to derive time integrated point estimates. The sensitivity of the amphipod, O. pinguides, to metals increased with increasing exposure time. Response times varied for different metals with amphipods responding faster to copper than to cadmium, lead or zinc. As indicated by 30 days lethal concentration (LC50) estimates, copper was the most toxic metal (31 µg/L), followed by cadmium (168 µg/L), lead (256 µg/L) and zinc (822 µg/L). Nickel exposure (up to 1.12 mg/L) did not affect amphipod survival. Using longer exposure durations and utilising the GAMM model provides an improved methodology for assessing sensitivities of slow responding Antarctic marine invertebrates to contaminants.

Carbon coated Na7Fe7(PO4)6F3: A novel intercalation cathode for sodium-ion batteries

Electrode materials are being developed to realise sodium-ion batteries that can provide energy storage solutions. Here, we develop amorphous carbon coated Na₇Fe₇(PO₄)₆F₃, prepared by combining hydrothermal and solid state reaction methods, as an insertion electrode for sodium-ion batteries applications. Na₇Fe₇(PO₄)₆F₃ particles are surrounded by a thin layer (∼1.5–2 nm) of amorphous carbon. The Na₇Fe₇(PO₄)₆F₃/C composite cathode undergoes reversible sodium intercalation/de-intercalation with an average operational potential of ∼3.0 V (vs Na⁺/Na). This cathode has a capacity of 65 mA h g⁻¹ at 100 mA g⁻¹ current after 60 cycles and features twice higher capacity than that of an uncoated Na₇Fe₇(PO₄)₆F₃ sample. Therefore, the carbon-coated Na₇Fe₇(PO₄)₆F₃ composite presents feasible sodium intercalation/de-intercalation capacity, offering possibilities for developing a low cost, high performance sodium-ion battery positive electrode.