Combined nano- and macrotribology studies of titania lubrication using the oil-ionic liquid mixtures

The lubrication of titania surfaces using a series of ionic liquid (IL)-hexadecane mixtures has been probed using nanoscale atomic force microscopy (AFM) and macroscale ball-on-disk tribometer measurements. The IL investigated is trihexyl(tetradecyl)phosphonium bis(2,4,4-trimethylpentyl)phosphinate, which is miscible with hexadecane in all proportions. At both length scales, the pure IL is a much more effective lubricant than pure hexadecane. At low loads, which are comparable to common industrial applications, the pure IL reduces the friction by 80% compared to pure hexadecane; while the IL-hexadecane mixtures lubricate the titania surface as effectively as the pure IL and wear decreases with increasing IL concentration. At high test loads the adsorbed ion boundary layer is displaced leading to surface contact and high friction, and wear is pronounced for all IL concentrations. Nonetheless, the IL performs better than a traditional zinc-dialkyl-dithophosphate (ZDDP) antiwear additive at the same concentration.

Degradation of VOCs by phototcatalytic oxidation reactor using TiO2 pellets

Volatile Organic Compounds (VOCs) are air pollutants that come from burning fossil fuels and industrial emissions. They have potentially adverse health effects being carcinogenic and highly persistent in the environment. The use of photocatalytic oxidation to remove VOCs has the potential to be applied in indoor air quality improvement and industrial emission control. A fixed bed photocatalytic reactor was designed and built. UV black light lamps were installed in the reactor to provide a source of UV radiation. A non-film titania media as pellets were placed on the three fixed beds within the reactor. Toluene and acetone were used as indicators of VOCs during the experiment. With a flow rate of 12.75l/min, the oxidation efficiencies were obtained at four different concentrations of acetone laden gas streams ranging from 40ppm to 250ppm. It was found that the lower the acetone concentration of the untreated inlet gas, the higher the oxidation efficiency. The oxidation efficiency was in the range of 40–70% for various concentrations of untreated gases. Two concentrations of toluene laden gas stream were also tested using the same reactor. The oxidation efficiencies were found as 50% for 120ppm toluene gas and 45% for 300ppm toluene gas. It was found that the times required for toluene to reach oxidization equilibrium have been halved than for acetone gas stream. Other parameters such as flow rate and UV intensity were also altered to see their effects on the oxidation efficiency. A full spectrum scan was carried out using a Bio-rad Infrared spectrometer. It was found that the main components of the treated gas stream from the outlet of the reactor were CO2 and water along with small amount of untreated acetone. The suspected intermediates of aliphatic hydrocarbons and CO were found in very minimal amounts or undetectable. The research experiments supported that the TiO2 pellets can work effectively in a fixed bed photocatalytic reactor and achieve significant oxidation efficiencies for degradation of toluene and acetone as indicators of VOCs.

A comparative study on preparation of TiO2 pellets as photocatalysts based on different precursors

The porous Ti0₂ pellets were prepared based on pigment grade titaina, P25 titania powder and titaniurn(lV) butoxide. The characterization was done with X-Ray diffraction, scanning electron microscopy and BET measurements. The result shows that Ti0₂ pellets by using titaniurn(IV) butoxide with some addictive have the best surface porosity, with specific surface area of 196.9m²/g. For pigment grade titania and P25 titania powder, it is still effective to enhance the surface area after reassembling. The surface area increased from 11.6 to 29.2 m²/g for pigment grade titania and from 50 to 84.4 m²/g for P25 titania powder. Furthermore, it has been investigated on how to optimize and get the highest surface area by controlling the sintering temperature, reaction temperature, pH of solution, and the amount of alcohol and addictive of surfactant during preparation. The experimental photocatalytic degradation of acetone and toluene was performed using titania pellets made from P25 titania powder.

Sol-gel derived HA/TiO2 double coatings on Ti scaffolds for orthopaedic applications

Hydroxyapatite/titania (HA/TiO₂) double layers were coated onto Ti scaffolds throughout for orthopaedic applications by sol-gel method. Differential scanning calorimetry (DSC), thermogravimetric analysis (TG) and X-ray diffractometry (XRD) were used for the characterisation of the phase transformations of the dried gels and coated surface structures. Scanning electron microscope (SEM) equipped with energy dispersive spectrometry (EDS) was used for the observation and evaluation of the morphology and phases of the surface layers and for the assessment of the in vitro tests. The in vitro assessments were performed by soaking the HA/TiO₂ double coated samples into the simulated body fluid (SBF) for various periods. The TiO₂ layer was coated by a dipping-coating method at a speed of 12 cm/min, followed by a heat treatment at 600 °C for 20 min. The HA layer was subsequently dipping-coated on the outer surface at the same speed and then heat-treated at difference temperatures. The results indicat that the HA phase begins to crystallize after a heat treatment at 560 °C. The crystallinity increases obviously at 760 °C. SEM observations find no delamination or crack at the interfaces of HA/TiO₂ and TiO₂/Ti. The HA/TiO₂ coated Ti scaffolds displays excellent bone-like apatite forming ability when it is soaked into SBF. Ti scaffolds after HA/TiO₂ double coatings can be anticipated as promising implant materials for orthopaedic applications

Visibly transparent UV photoprotective compositions

A broad-spectrum UV photoprotective composition is described. The composition is characterized in that the composition comprises mesoporous zinc oxide aggregates having an average aggregate size of at least 0.8 microns dispersed in a carrier and the composition is visibly transparent. Sufficient zinc oxide is included in the composition to achieve an SPF greater than 15, greater than 25, greater than 30, or greater than 50.

Bioactivating the surfaces of titanium by sol-gel process

In the present study, titanium (Ti) samples were surface-modified by titania (TiO₂), silica (SiO₂) and hydroxyapatite (HA) coatings using a sol-gel process. The bioactivity of the film-coated Ti samples was investigated by cell attachment and morphology study using human osteoblast-like SaOS-2 cells. Results of the cell attachment indicated that the densities of cell attachment on the surfaces of Ti samples were significantly increased by film coatings; the density of cell attachment on HA film-coated surface was higher than those on TiO₂ and SiO₂ film-coated surfaces. Cell morphology study showed that the cells attached, spread and grew well on the three kinds of film-coated surfaces. It can be concluded that the three kinds of film coatings can bioactivate the surfaces of Ti samples effectively. Overall, Ti sample with HA film-coated surface exhibited the best bioactivity.

Surface evolution of a gradient structured Ti in hydrogen peroxide solution

In this work, the interaction between hydrogen peroxide (H₂O₂) and a gradient structured Ti was investigated extensively. The gradient structured Ti (SMAT Ti) was produced by surface mechanical attrition treatment (SMAT), and then it was immersed in H₂O₂ solution for different time until 48 h at room temperature (25 °C). The structure and surface morphology evolution were examined by Raman spectra and scanning electron microscopy (SEM). The formation mechanism of nanoporous titania was discussed based on above results.

Proton conductive composite membranes

In this work we investigated the synthesis of composite organic and inorganic membranes for proton conduction. Particles derived from metal alkoxides (M(OR)n) sol-gel processes (Ti, Zr, W with phosphoric acid) were embedded in polymeric matrices of poly-vinyl alcohol, (3-glycidoxypropyl)-trimethoxysilane and ethylene glycol. The structure of the composite membranes was complex as several IR peaks were convoluted, indicating the assignment of several functional groups. However, the peaks assigned to OH groups reduced in intensity in the composite membranes, indicating that cross-linking of hydroxyl groups in the organic and inorganic phases of the membrane may have occurred. The particles allowed for re-arrangement of the polymer matrix, as crystallinity was reduced compared to a polymer blank membrane. The composite membrane process resulted in homogeneous dispersion of nanoparticles into the polymer film. Proton conduction of the inorganic phase was mainly dominated by titania. Binary mixtures of titania phosphate (sample name TiP) resulted in proton conduction of 7.15 × 10−2 S.cm−1, one order of magnitude higher than zirconia phosphate (ZrP). The addition of Zr and W to TiP forming ternary or quaternary phases also led to lower proton conduction as compared to TiP. Similar trends were also observed for the composite membranes, though the TiP composite membrane proton conduction reduced after several hours of testing at 50°C, which was mainly attributed to acid leaching.

Toward design of synergistically active carbon-based catalysts for electrocatalytic hydrogen evolution

Replacement of precious Pt catalyst with cost-effective alternatives would be significantly beneficial for hydrogen production via electrocatalytic hydrogen evolution reaction (HER). All candidates thus far are exclusively metallic catalysts, which suffer inherent corrosion and oxidation susceptibility during acidic proton-exchange membrane electrolysis. Herein, based on theoretical predictions, we designed and synthesized nitrogen (N) and phosphorus (P) dual-doped graphene as a nonmetallic electrocatalyst for sustainable and efficient hydrogen production. The N and P heteroatoms could coactivate the adjacent C atom in the graphene matrix by affecting its valence orbital energy levels to induce a synergistically enhanced reactivity toward HER. As a result, the dual-doped graphene showed higher electrocatalytic HER activity than single-doped ones and comparable performance to some of the traditional metallic catalysts.

Nucleic acid aptamer-guided cancer therapeutics and diagnostics: the next generation of cancer medicine

Conventional anticancer therapies, such as chemo- and/or radio-therapy are often unable to completely eradicate cancers due to abnormal tumor microenvironment, as well as increased drug/radiation resistance. More effective therapeutic strategies for overcoming these obstacles are urgently in demand. Aptamers, as chemical antibodies that bind to targets with high affinity and specificity, are a promising new and novel agent for both cancer diagnostic and therapeutic applications. Aptamer-based cancer cell targeting facilitates the development of active targeting in which aptamer-mediated drug delivery could provide promising anticancer outcomes. This review is to update the current progress of aptamer-based cancer diagnosis and aptamer-mediated active targeting for cancer therapy in vivo, exploring the potential of this novel form of targeted cancer therapy.

Electrospun granular hollow SnO2 nanofibers hydrogen gas sensors operating at low temperatures

In this paper, we present H2 gas sensors based on hollow and filled, well-aligned electrospun SnO2 nanofibers, operating at a low temperature of 150 C. SnO2 nanofibers with diameters ranging from 80 to 400 nm have been successfully synthesized in which the diameter of the nanofibers can be controlled by adjusting the concentration of polyacrylonitrile in the solution for electrospinning. The presence of this polymer results in the formation of granular walls for the nanofibers. We discussed the correlation between nanofibers morphology, structure, oxygen vacancy contents and the gas sensing performances. X-ray photoelectron spectroscopy analysis revealed that the granular hollow SnO2 nanofibers, which show the highest responses, contain a significant number of oxygen vacancies, which are favorable for gas sensor operating at low temperatures. © 2014 American Chemical Society.