Non-Schmid behaviour during secondary twinning in a polycrystalline magnesium alloy

The present work combines electron backscattering diffraction and Schmid analysis to investigate secondary twinning in the magnesium alloy Mg–3Al–1Zn. Inspection of the misorientations between the parent and ^{{1011} - {1012}} doubly twinned volumes reveals that there are four possible variants. One of these variants (the one that forms a misorientation with the matrix characterized by 38°^⟨1210⟩ ) is favoured much more than the others. This variant involves the activation of secondary twinning systems quite inconsistent with Schmid-type behaviour. For the secondary twin to grow significantly it must take on a shape enforced by the primary twin. This is non-optimal for strain compatibility. It is argued that the 38°^⟨1210⟩ variant occurs most because it provides the closest match between the primary and secondary twinning planes, thus minimizing the compatibility strain.

Effect of microalloying with rare-earth elements on the texture of extruded magnesium-based alloys

A series of alloys have been produced with microalloying additions of rare-earth (RE) elements in the range of 0.1–0.4 wt.%. The alloys have been extruded to produce grain sizes of 23 ± 5 μm. The texture of the extruded alloys was measured, and it was found that the extrusion texture was weakened by the addition of RE elements. The samples with weakened extrusion textures exhibited an increase in the tensile elongation.

Titanium–nickel shape memory alloy foams for bone tissue engineering

Titanium–nickel (TiNi) shape memory alloy (SMA) foams with an open-cell porous structure were fabricated by space-holder sintering process and characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. The mechanical properties and shape memory properties of the TiNi foam samples were investigated using compressive test. Results indicate that the plateau stresses and elastic moduli of the foams under compression decrease with the increase of their porosities. The plateau stresses and elastic moduli are measured to be from 1.9 to 38.3 MPa and from 30 to 860 MPa for the TiNi foam samples with porosities ranged from 71% to 87%, respectively. The mechanical properties of the TiNi alloy foams can be tailored to match those of bone. The TiNi alloy foams exhibit shape memory effect (SME), and it is found that the recoverable strain due to SME decreases with the increase of foam porosity.

Magnesium alloy applications in automotive structures

The energy absorbed by magnesium alloys (high-pressure die-cast (HPDC) AM20, AM50, AM60, and extruded AZ31) in a buckling test was significantly greater than the aluminum alloy 6061 T6 and particularly mild steel of a similar weight, but was less than that of the aluminum alloy and steel for the same thickness (Figure 6).26 This indicates that mass savings can be achieved by the substitution with magnesium alloys to achieve similar energy-absorbing characteristics.

Texture and mechanical anisotropy in three extruded magnesium alloys

One ZM61 alloy (6·2%Zn, 1·2%Mn) and two magnesium alloys containing nominally 3% of neodymium and yttrium respectively have been prepared in the form of hot extruded flat strips. Their textures and microstructures have been quantified and series of mechanical tests were carried out to determine plane stress yield loci in both the solution treated and aged conditions. The ZM61 alloy had a sharp texture and marked anisotropy of strength that could be rationalised in terms of deformation by basal <a> slip and {1012}<1011> twinning. This material was much weaker in compression than in tension. Precipitation hardening on aging caused a greater impedance to twinning than to slip with the result that the anisotropy was somewhat reduced. The Mg–3Nd alloy had a very weak and different texture but nevertheless demonstrated a pronounced anisotropy of strength. Aging increased the yield stress by about 80% and also inhibited twinning to some extent although the degree of anisotropy remained almost unaffected. The Mg–3Y alloy which showed a texture of intermediate strength was different in type from either of the others. Its strength behaviour was close to isotropic; in particular, no difference existed between tensile and compressive loading, and aging produced only a marginal increase in strength. Twins were relatively infrequent in the deformed Mg–3Y alloy but its mechanical behaviour could not be rationalised according to simple models.

Identification and rationalization of secondary twin variants in a magnesium alloy

The present work combines electron backscatter diffraction, transmission electron microscopy and Schmid analysis to investigate secondary twinning in the magnesium alloy Mg-3AI-1Zn. Inspection of the misorientations between the parent matrix and {1011} - {1012} doubly twinned volumes reveals that there are four possible variants. One of these variants characterized by 38°< 1210 > misorientation with the matrix is favoured much more than the others. This variant involves activation of the secondary twinning systems that are quite inconsistent with the Schmid-type behaviour. For the secondary twin to grow significantly it must take on a shape enforced by the primary twin, however, this is not optimal for strain compatibility. It is argued that the 38° < 1210 > variant occurs most frequently because it provides the closest match between the primary and secondaty twinning planes, thus minimizing the compatibility strain. This conjecture is confirmed by the simulations of twin activity m ellipsoidal grains performed using the visco-plastic self-consistent crystal plasticity model.

Some issues relating to the ductility of wrought magnesium alloys

The present work is concerned with gaining a better understanding of the factors that control the ductility of wrought magnesium alloys. The ultimate aim is to develop alloys with vastly improved room temperature formability. It is shown that 3D tomography of fractured tensile specimens reveals disk shaped voids aligned more or less at 45 deg. to the tensile axis. These voids are consistent with twin induced void formation. It is also shown that the double twins that produce such voids form in contradiction to Schmid predictions. Finally, it is demonstrated that low levels of rare-earth additions leads to vastly improved texture and ductility in extrusions, as they do in rolled sheet.

Production and bioavailability of calcium and magnesium salts of omega-3 fatty acids

In order to provide an alternative to traditional liquid fish oil gelatin capsules, we developed a solid, powdered form of omega-3 fish oil concentrate by forming calcium- and magnesium-fatty acid salts. These salts were produced using a concentrated fish oil ethyl ester that contained in excess of 60% omega-3 fatty acids. The bioavailability of these omega-3 salts was compared with that of fish oil ethyl ester in mice. Animals were given 8 mg of omega-3 fatty acid ethyl ester concentrate (control), calcium- or magnesium-omega-3 salts daily for three weeks. The omega-3 salt products resulted in omega-3 fatty acid content in serum and red blood cell membranes comparable to that produced by the ethyl ester supplementation. In addition, fecal excretion of omega-3 fatty acids was not increased by the presence of calcium or magnesium. In fact, there was a tendency for less omega-3 fatty acids to be excreted.

Dietary fiber, potassium, magnesium and calcium in relation to the risk of preeclampsia

To explore the relation between preeclampsia risk and maternal intake of dietary fiber, potassium, magnesium and calcium. STUDY DESIGN: We conducted a case-control study of 172 preeclamptics and 339 normotensive controls. Maternal dietary intake was assessed using a food frequency questionnaire. Logistic regression procedures were used to estimate the association between each dietary factor and preeclampsia risk. RESULTS: Fiber intake was inversely associated with the risk of preeclampsia. When extreme quartiles of total fiber intake were compared, the odds ratio (OR) for preeclampsia was 0.46 (95% confidence interval [CI] 0.23-0.92). The multivariate OR for preeclampsia for women in the top quartile of potassium intake (>4.1 g/d) versus the lowest quartile (<2.4 g/d) was 0.49 (95% CI 0.24-0.99). There was some evidence of a reduced risk of preeclampsia with a high intake of magnesium and calcium, though these results were not statistically significant. Intake of fruits and vegetables, low-fat dairy products, total cereal and dark bread were each associated with a reduced risk of preeclampsia. CONCLUSION: Our results support previous reports that suggest that diets high in fiber and potassium are associated with a reduced risk of hypertension. Maternal intake of recommended amounts of foods rich in fiber, potassium and other nutrients may reduce the risk of preeclampsia.

Simulation of Mg sheet press cell materials

Major characteristics of Magnesium alloy are low density (= 1.8 g/cm³) and excellent recyclability; therefore Mg is considered as one of low environmental loading materials. The low-density materials, such as Mg, are suitable for the transportation system to reduce the emission of Co2, save energy resource and increase the safety for accidents like corrosions. In the place, cellular materials like aluminum foams are also low-density materials and can be controlled the stress-strain relation. Combination of Mg alloy and cellular materials, that is Mg cell, is one of the most excellent materials for transportation system, because of its ultra low density. safeties, and recycle ability. To make the Mg cellular materials. there are some problems to solve. One is how to make them uniformly to supply them as same perfonnance materials. One is how to make them inexpensively. Most of cellular materials are very expensive because of there are many processes or special fabrication system to make them. To solve these problems. we investigated the press cell materials. The press cell material consists sheets pressed as cell shape and wall. Therefore, it is very easy to make cellular materials and control validation of the performance of each foam materials. In this paper, we simulated compression tests of this new type of Mg alloy cellular materials under dynamic loading to investigate the relation between the compression speed and the compression behavior to show the shock absorbing capability of this new foam material. It is very important to understand their mechanical properties relatcd with cell shapes and wall to be applied widely.

Influence of alloying additions on the extrudability of magnesium

The extrusion behaviour of a series of magnesium alloys was investigated and compared to a common aluminium alloy using limit diagrams. The variation in the limits was related to the different flow stress and solidus temperature of each alloy. The findings of this work have enabled predictions of the relative extrudability of new prototype alloys.

Low temperature formability of differently processed AZ31B magnesium alloy sheets

The research found changes in the performance (formability) of magnesium alloy sheets with a history of different processes. A key outcome found that the steel sheet metal processing of rolling and heat treatment caused a detrimental effect. The material's internal deformation was found to be linked to the poor formability.

Behavior of magnesium in Hank's solution aimed to trabecular pattern of natural bone

An ideal artificial bone is expected to grow together with other natural bones with aid of osteoblast cells and to fade out into other natural bones at the same rate of restructuring natural bone. Magnesium is thought to be one of candidate materials, since it has a potential to enhance natural bone growth and to homogenize the implanted artificial bodies with natural bone. In the present study, we are concerned with the formation of trabecular pattern in the natural bone to consider how to reconstruct this pattan in the artificial bone made from magnesium. For that purpose, a series of experiments were perfonned to observe the chemical behavior of dipped magnesium plate and cellular magnesium in Hank's solution. A magnesium specimen is annealed at 773 - 803 K for various periods in an atmosphere to homogenize its microstructure. Mass change of magnesium is estimated by immersing it in Hank's solution. It is well known that magnesium is easily corroded by chlorine ion. Both x-ray diffraction and energy dispersed x-ray analyses were carried out in order to identify a reaction product and its chemical composition. Mass of a magnesium specimen, which was annealed at 803 K for 32.4 ks or 14.4 ks, increases after immersing it into Hank's solution for 4.5 18 Ms (1255 h). Furthermore, the cellular magnesium, which was annealed at 803 K for 1.8 ks, fanned a reacted layer with around 80 μ in thickness and it contained Mg, Ca, P, and a little bit of CI.

Anisotropic mechanical properties of nickel foams fabricated by powder metallurgy

In the present study, porous nickel foam samples with pore sizes of 20 μm and 150 μm and porosities of 60 % and 70 % were fabricated by the space-holding sintering method via powder metallurgy. Electron scanning microscopy (SEM) and Image-Pro Plus were used to characterise the morphological features of the porous nickel foam samples. The anisotropic mechanical properties of porous nickel foams were investigated by compressive testing loading in different directions, i.e. the major pore axis and minor pore axis. Results indicated that the nominal stress of the nickel foam samples increases with the decreasing of the porosity. Moreover, the foam sample exhibited significantly higher nominal stress for loading in the direction of the major pore axis than loading in direction of the minor pore axis. It is also noticeable that the nominal stress of the nickel foams increases with the decreasing of the pore size. It seems that the deformation behaviour of the foams with a pore size in the micron-order differs from those with a macro-porous structure.