Effect of particles on the formation of deformation twins in a magnesium-based alloy

The deformation behaviour of the age hardenable alloy Mg–5%Zn after different precipitation treatments has been examined. It has been found that during compressive deformation, fine particles increase the number of twins that form, but reduce the size and total volume fraction of twins. Visco-plastic selfconsistent modelling has been used to show that the presence of precipitates hardens the twin and prismatic slip systems more than the basal slip system. It is proposed that because the {10 ¯12} twin requires basal slip to accommodate the twinning shear, this twin type will always be hardened equal to, or more than, the basal slip system in response to precipitation.

Utilization of a new bdelloid rotifer (Philodina acuticornis odiosa) assay to evaluate the effect of salinity on the toxicity of chlorothalonil

Acute (24 h) toxicity tests were conducted to determine the toxicity of the fungicide chlorothalonil towards the freshwater bdelloid rotifer (Philodina acuticornis odiosa). Since rotifers are the dominant zooplankton species in many inland freshwater lakes in Australia, the influence of salinity on chlorothalonil toxicty was also assessed. The rotifers used in this study appeared to be reasonably tolerant to changes in salinity, with little mortality observed at 3760 µS cm-1, increasing thereafter at higher salinity. The bdelloid rotifers were, however, found to be highly sensitive to chlorothalonil (24 h LC50, 3.2 µg L-1) with results also suggesting that as salinity increases, so does toxicity (e.g., 24 h LC50 at 5000 µS cm-1, 0.5 µg L-1).

Purification or contamination? The effect of sorbents on ionic liquids

Commonly used for purification, alumina and silica are found to contaminate ionic liquids with particles; these particles cannot be removed easily and can have a non-negligible impact on the electrochemical, spectroscopic and physical properties of an ionic liquid, including its nucleation and crystallisation kinetics.

Superhydrophobic fabrics from hybrid silica sol-gel coatings: Structural effect of precursors on wettability and washing durability

Particle-containing silica sol was synthesized by co-hydrolysis and co-condensation of two silane precursors, tetraethylorthosilicate (TEOS) and an organic silane composed of a non-hydrolyzable functional group (e.g., alkyl, flourinated alkyl, and phenyl), and used to produce superhydrophobic coatings on fabrics. it has been revealed that the non-hydrolyzable functional groups in the organic silanes have a considerable influence on the fabric surface wettability. When the functional group was long chain alkyl (C16), phenyl, or flourinated alkyl (C8), the treated surfaces were highly superhydrophobic with a water contact angle (CA) greater than 170°, and the CA value was little affected by the fabric type. The washing durability of the superhydrophobic coating was improved by introducing the third silane containg epoxide group, 3-glycidoxypropyltrimethoxsilane (GPTMS), for synthesis. Although the presence of epoxide groups in the coating slightly reduced the fabrics' superhydrophobicity, the washing durability was considerably improved when polyester and cotton fabrics were used as substrates.

Effect of coagulants on the fouling and performance of ultrafiltration (UF) membranes

The combined coagulation and ultrafiltration (UF) system (C-UF system) is an advanced technology to treat natural organic matter (NOM) present in water. Traditional coagulants — prehydrolyzed inorganic coagulants, organic coagulants and composite coagulants were chosen to treat synthetic water containing humic acid (HA) in order to find an efficient coagulant that could remove NOM from the water effectively. The fouling, removal efficiency of UF and the chlorine decay in the permeate were used to evaluate the effectiveness of the coagulants. The initial UV254 absorption of the tested water samples were from 0.208 to 0.234, and the UV254 after coagulation was from 0.05 to 0.184. The UV254 did not increase after coagulation. Since the humic acid used was soluble, the initial turbidity of the tested water samples were very close to zero. The turbidity increased after coagulation, as the coagulants react with humic acid to form micro-flocs, which cannot be removed fully by sedimentation. The results showed that polyferric chloride could not remove humic acid efficiently during coagulation process, but removed the humic acid well when used in the C-UF system. Moreover, for polyferric chloride and UF system, the concentration of organic compounds in permeates were minimal indicating very low levels of disinfection by-product formation, if chlorinated.