Modelling the fate of chromated copper arsenate in a sandy soil

A pulse of chromated copper arsenate (CCA, a timber preservative) was applied in irrigation water to an undisturbed field soil in a laboratory column. Concentrations of various elements in the leachate from the column were measured during the experiment. Also, the remnants within the soil were measured at the end of the experiment. The geochemical modelling package, PHREEQC-2, was used to simulate the experimental data. Processes included in the CCA transport modelling were advection, dispersion, non-specific adsorption (cation exchange) and specific adsorption by clay minerals and organic matter, as well as other possible chemical reactions such as precipitation/dissolution. The modelling effort highlighted the possible complexities in CCA transport and reaction experiments. For example, the uneven dosing of CCA as well as incomplete knowledge of the soil properties resulted in simulations that gave only partial, although reasonable, agreement with the experimental data. Both the experimental data and simulations show that As and Cu are strongly adsorbed and therefore, will mostly remain at the top of the soil profile, with a small proportion appearing in leachate. On the other hand, Cr is more mobile and thus it is present in the soil column leachate. Further simulations show that both the quantity of CCA added to the soil and the pH of the irrigation water will influence CCA transport. Simulations suggest that application of larger doses of CCA to the soil will result in higher leachate concentrations, especially for Cu and As. Irrigation water with a lower pH will dramatically increase leaching of Cu. These results indicate that acidic rainfall or significant accidental spillage of CCA will increase the risk of groundwater pollution.

A sensitive procedure for the rapid determination of arsenic(III) by flow injection analysis and chemiluminescence detection

A novel chemiluminescence flow injection procedure for the determination of As(III) in aqueous samples is described. The method involves injection of As(III) samples into a 1% (m/v) sodium hexametaphosphate in 0.02 M H₂SO₄ carrier stream, which then merges at a Y-piece with a reagent stream consisting of potassium permanganate (5.0 × 10⁻⁵ M) made up in the acidic sodium hexametaphosphate carrier solution. The chemiluminescence intensity of the resulting reaction mixture was measured at a photomultiplier tube operated at a voltage of 0.93 kV. Under optimized conditions, the method is characterised by a linear range from 0.5 to 5.0 μg l⁻¹, a detection limit of 0.3 μg l⁻¹ and a sampling frequency of 150 h⁻¹. The effects of common anionic and cationic interferences were investigated, and it was found that the only ions to cause serious interference were those which react with potassium permanganate, namely sulphide, iodide and ferrous.

Anion recognition and sensing in organic and aqueous media using luminescent and colorimetric sensors

This review article focuses primarily on the work carried in our laboratories over the last few years using luminescent and colorimetric sensors, where the anion recognition occurs through hydrogen bonding in organic or aqueous solvents. This review begins with the story of the discovery of fluorescent photoinduced electron transfer (PET) sensors for anions using charged neutral urea or thiourea receptors where both fluorescent and NMR spectroscopic methods monitored anion recognition. This work led to the development of dual luminescent and colorimetric anion sensors based on the use of the ICT based naphthalimide chromophore, where ions such as fluoride gave rise to changes in both the fluorescence and the absorption spectra of the sensors, but at different concentrations. Here, the former changes were due to hydrogen bonding interactions, whereas the latter was due to the deprotonation of acidic protons, giving rise to the formation of the bifluoride anion (HF2−). Modification of the 4-amino-l,8-naphthalimide moiety has facilitated the formation of colorimetric anion sensors that work both in organic or aqueous solutions. Such charge neutral receptor motifs have also been incorporated into organic scaffolds with norbomyl and calixarene backbones, which have enabled us to produce anion directed self-assembled structures.

Chemiluminescence: liquid-phase

Article Outline
• Introduction
• Acidic Potassium Permanganate
• Acridinium Esters
• Diaryl Oxalates and Oxamides
• Dioxetanes
• Hypohalites
• Luminol and Its Analogs
• Tris(2,2′-bipyridyl)ruthenium(II)
• Practical Considerations
• HPLC and Flow Analysis
• Capillary Electrophoresis
• Enzyme Reaction Products
• Immunoassay and DNA Assays
• Further Reading

Effects of laundering on conductivity of polypyrrole-coated textiles

This study examines the resistance change in conductive polypyrrole-coated PET fabrics under the AS 2001.4.15 – 1994 laundering test conditions. The effects of individual detergent components of a standard detergent, including auxiliary chemicals, at four different temperatures were studied. When the coated fabric was washed under the AS 2001.4.15-1994 conditions, the ECE reference detergent and pure soap flakes (sodium sterate) both decreased the conductivity of the coating at a rate exponentially proportional to the laundering temperature. Detergent types had an influence over the rate of degradation; pH conditions had a large influence on the rate of polymer deterioration with the acidic nonionic detergent giving rise to significantly improved laundering conditions. The auxiliary chemicals, sodium carbonate and sodium perborate were seen to cause large degradation of polymers during laundering. Ethylene diamine tetra acetic acid was seen to have only a slight influence on the reduction of conductivity of polymers.

A screening test for heroin based on sequential injection analysis with dual-reagent chemiluminescence detection

A sequential injection analysis procedure with dual-reagent chemiluminescence detection was applied to the screening of street drug seizure samples for the presence of heroin. The chemiluminescence reagents (acidic potassium permanganate and tris(2,2′-bipyridine)ruthenium(III)) were aspirated from either side of a sample aliquot that was sufficiently large to prevent interdispersion of the reagent zones, and therefore two different chemical reactions could be performed simultaneously at either end of the sample zone. The presence of heroin in seizure samples was indicated by a strong response with the tris(2,2′-bipyridine)ruthenium(III) reagent and confirmed by a significant increase in the response with the permanganate reagent when the sample was treated with sodium hydroxide to hydrolyse the heroin to morphine. Nicomorphine (a morphine-derived pharmaceutical) was synthesised and tested under the same conditions. The responses with the permanganate reagent were similar to those for heroin, which supports the proposed chemical basis for the test. However, the responses with tris(2,2′-bipyridine)ruthenium(III) were far lower for nicomorphine than heroin (approximately 5-fold for the samples that had not been hydrolysed).

Chemiluminescence detection of opium poppy (papaver somniferum) alkaloids

A review with 98 references. The determination of the opium poppy (Papaver somniferum) alkaloids and their semi-synthetic derivatives has important applications in industrial process monitoring, clinical analysis and forensic science. Liquid-phase chemiluminescence reagents such as tris(2,2′-bipyridyl)ruthenium(II) and acidic potassium permanganate exhibit remarkable sensitivity and complementary selectivity for many P. somniferum alkaloids, which has been exploited in the development of a range of analytical procedures using flow analysis, high-performance liquid chromatography, capillary electrophoresis and microfluidic instrumentation.

Chemiluminescence detector with a serpentine flow cell

We present a new chemiluminescence detector, with solution channels that have been machined into a Teflon disk and sealed with a sapphire window. The configuration of the flow cell can be conveniently modified by replacing the Teflon disk. A comparison of some existing and novel designs, using the chemiluminescence reaction of morphine with acidic potassium permanganate and the bioluminescence reaction of ATP with the commercially available “BacTiter-Glo” reagent, has revealed that a serpentine channel allows greater quantities of light to be captured than a spiral channel, due to more efficient mixing of the analyte and reagent solutions within the cell.

Electroless synthesis of nano-structured gold particles using conducting polymer nanoparticles

In this study, gold nanoparticles were synthesized by electroless recovery of [AuCl4]− from an acidic aqueous solution using nano-structured conducting polymer, polypyrrole nanoparticles, as active surface. The formation of gold nanoparticles was confirmed by TEM, SEM and EDX measurements. The effects of the initial Au(III) concentration on the gold uptake was examined. The recovery capability and gold particle morphology prepared from polypyrrole nanoparticle were compared to that from cast PPy film counterpart.

Evaluation of tris(4,7-diphenyl-1,10-phenanthrolinedisulfonate)ruthenium(II) as a chemiluminescence reagent

Previous studies have suggested that tris(4,7-diphenyl-1,10-phenanthrolinedisulfonate)ruthenium(II) (Ru(BPS)₃⁴⁻) has great potential as a chemiluminescence reagent in acidic aqueous solution. We have evaluated four different samples of this reagent (two commercially available and two synthesised in our laboratory) in comparison with tris(2,2′-bipyridine)ruthenium(II) (Ru(bipy)₃²⁺) and tris(1,10-phenanthroline)ruthenium(II) (Ru(phen)₃²⁺), using a range of structurally diverse analytes. In general, Ru(BPS)₃⁴⁻ produced more intense chemiluminescence, but the oxidised Ru(BPS)₃³⁻ species is less stable in aqueous solution than Ru(bipy)₃³⁺ and produced a greater blank signal than Ru(bipy)₃³⁺ or Ru(phen)₃³⁺, which had a detrimental effect on sensitivity. Although the complex is often depicted with the sulfonate groups of the BPS ligand in the para position on the phenyl rings, NMR characterisation revealed that the commercially available BPS material used in this study was predominantly the meta isomer.

Investigations into the analytical applications and fundamental chemistry of the chemiluminescent reactions of Tris(2,2'-bipyridyl)ruthenium(III) with certain Papaver Somniferum alkaloids and other related compounds

The reaction of tris(2,2’-bipyridyl)ruthenium(III) (Ru(bipy) ₃³⁺) with various analytes to generate chemiluminescence has been well documented. This investigation sought to undertake a chemiluminometic study of the reactions of Ru(bipy) ₃³⁺ with selected Papaver Somniferum alkaloids and specifically synthesised phenethylamines. The investigation, based on a kinetic study, primarily addressed the effect of varying reaction conditions (pH) on Ru(bipy) ₃³⁺ chemiluminescence production. To monitor these reactions, a batch chemiluminometer was specifically designed, fabricated and automated to conduct an extensive study on the selected compounds of interest. The instrumentation incorporated a custom built reaction cell and comprised an ‘on-line’ sample preparation system with which calibration standards could be automatically prepared. The instrumentation provided both time-independent (peak area) and time-dependent (kinetic profile) information. A novel approach to the stabilisation of Ru(bipy) ₃³⁺ as a chemiluminescencent reagent was also investigated and a recirculating system was employed with the batch chemiluminometer to provide a stable supply of Ru(bipy) ₃³⁺. Codeine, thebaine and 6-methoxy-codeine were the Papaver Somniferum alkaloids selected for this study and several N-methylated and N,N-dimethylated phenethylamines and methoxy-substituted phenetheylamines were also synthesised to investigate the affect of pH on the chemiluminescence emission efficiency. The versatility of the batch chemiluminometer facilitated the kinetic study of numerous analytes over a broad pH range. The exemplary performance of the chemiluminometer as an analytical instrument, was demonstrated by the calibration functions, based on peak area data, which exhibited excellent linearity and sensitivity. The estimated detection limits (3s) for the selected alkaloids were in the range 2 x 10^-9 M to 7 x 10^-9 at pH 5.0 and above, which compared favourably to detection limits for the same compounds determined using FIA. Relative standard deviations (n=5) for peak areas ranged between 1% to 5% with a mean of 3.1% for all calibration standards above 2.5 x 10^-8 M. Correlation between concentration and peak area, irrespective of pH and analyte was excellent, with all but two calibration functions having r-squared values greater than 0.990. The analytical figures of merit exemplified the precision and robustness of the reagent delivery and ‘on-line’ sample preparation, as well as the sensitivity of the system. The employment of the chemiluminometer for the measurement of total chemiluminescence emission (peak area) was in itself a feasible analytical technique, which generated highly reproducible and consistent data. Excellent analytical figures of merit, based on peak area, were similarly achieved for the phenethylamines. The effects of analyte structure on chemiluminescence activity was also investigated for the alkaloids and the phenethylamines. Subtle structural variations between the three alkaloids resulted in either a moderately reduced or enhanced total emission that was two or three fold difference only. A significant difference in reaction kinetics was observed between thebaine and codeine/6-methoxy-codeine, which was dependent upon pH. The time-dependent data, namely the observed rate constants for the initial rise in intensity and for the subsequent decay rate, were obtained by fitting a mathematical function (based on the postulated reaction mechanism) to the raw data. The determination of these rate constants for chemiluminescence reactions highlighted the feasibility for utilising such measurements for quantitative analytical applications. The kinetic data were used to discriminate between analyte responses in order to determine the concentrations of individual analytes in a binary mixture. A preliminary, multi-component investigation performed on a binary mixture of codeine and 6-methoxy-codeine (1:1) successfully determined the concentrations of these individual components using such rate constant measurements. Consequently, variations in kinetics resulted in a significant difference between the relative chemiluminescence response based on peak area measurements and the relative response base on peak height measurements obtained using FIA. With regards to the observed reactivity of secondary amines and tertiary amines, chemiluminescence peak area determinations confirmed the vital role of pH on reaction efficiency, which was governed by structural features and kinetics. The tertiary amines investigated generally produced a greater emission under acidic conditions than the corresponding secondary amines. However, the measured chemiluminescence responses were highly dependent upon pH, with similar peak areas obtained for both amine groups under slightly alkaline conditions.

Potential antiarrhythmic and cardioprotective agents based on adenosine

N-Ethylcarboxamidoadenosine (12) was synthesised from adenosine (1) and the 6-chloro-2’,3’-O-isopropylidene-AT-ethylcarboxamidoadenosine (25) was synthesised from inosine (19). Employing molecular modelling techniques and the results from previous structure activity relationships it was possible to design and synthesise a N6-substituted N-ethylcarboxamidoadenosines which possessed an oxygen in the N6-substituent either in the form of an epoxide (which was obtained by cpoxidising an alkene with m-CPBA or dimethyldioxirane) or in the form of a cyclic ether as was the case for N6-((tetrahydro-2H--pyran--2-yl)methyl-N-ethylcarboxamidoadenosine (78). These compounds were tested for their biological activity at the A1 adenosine receptor by their ability to inhibit cAMP accumulation in DDT, MF2 cells. The EC50 values obtained indicated that the N6-(norborn-5-en-2-yl)-N-ethylcarboxamidoadenosines were the most potent. Of theseN6-(S-endo-norbrn-5-en-2-yI)-N-ethylcarboxaniidoadenosine (56) was the most potent (0.2 nM). N6-(exo-norborn-5-en-2-yl)-2-iodo-N-ethylcarboxamidoadenosine (79) was synthesised from guanosine (22) and was also evaluated for its potency at the A, receptor (24.8 ± 1.5 nM). At present 79 is being evaluated for its selectivity for the A1 receptor compared to the other three receptor subtypes (A2a, A2b, A3). A series of N6-(benzyl)-N-ethylcarboxamidoadenosines were synthesised with substitutions at the 4-position of the phenyl ring. Another series of compounds were synthesised which replaced the methylene spacer between the N6H and the N6-aromatic or lipophilic substituent The replacement groups -were carbonyl and trans-2- cyclopropyl moieties. The N6-acyl compounds were obtained by reacting 2’,3’-O- di(tert-butyldimethylsilyl)-AT-ethylcarboxamidoadenosinc (59) with the appropriate acid chloride and then deprotecting with lelrabutylammonium fluoride in tetrahydrofuran. The compound N6-(4-(1,2-dihydroxy)ethyl)benzyl-N- ethylcarboxamidoadenosine (125) was synthesised by the reaction of 4-(1,2-0- isopropylidene-ethyl)benzyl aminc (123) with 6-chloro-2,3-0-isopropylidene-N- ethylcarboxamidoadenosine (25). Compound 123 was synthesised from an epoxidation of vinylbenzyl phthalimide (118) followed by an acidic ring opening to yield the diol which was isopropylidenated to yield 4-(l,2-O-isopropylidene- elhyl)benzyl phlhalimide (122), It was hoped that the presence of the diol functionality in 125 would increase water solubility whilst maintaining potency at the A3 receptor.

Chemistry, spectroscopy and analytical applications of certain chemiluminescent reactions

Chemiluminescence, the production of light from a chemical reaction, has found widespread use in analytical chemistry. Both tris (2, 2’-bipyridyl) ruthenium (II) and acidic potassium permanganate are chemiluminescence reagents that have been employed for the determination of a diverse range of analytes. This thesis encompasses some fundamental investigations into the chemistry and spectroscopy of these chemiluminescence reactions as well as extending the scope of their analytical applications. Specifically, a simple and robust capillary electrophoresis chemiluminescence detection system for the determination of codeine, O6-methylcodeine and thebaine is described, based upon the reaction of these analytes with chemically generated tris(2,2'-bipyridyl)ruthenium(III) prepared in sulfuric acid (0.05 M). The reagent solution was contained in a glass detection cell, which also held both the capillary and the cathode. The resultant chemiluminescence was monitored directly using a photomultiplier tube mounted flush against the base of the detection cell. The methodology, which incorporated a field amplification sample introduction procedure, realised detection limits (3a baseline noise) of 5 x 10~8 M for both codeine and O6-methylcodeine and 1 x 10~7 M for thebaine. The relative standard deviations of the migration times and the peak areas for the three analytes ranged from 2.2 % up to 2.5 % and 1.9 % up to 4.6 % respectively. Following minor instrumental modifications, morphine, oripavine and pseudomorphine were determined based upon their reaction with acidic potassium permanganate in the presence of sodium polyphosphate. To ensure no migration of the permanganate anion occurred, the anode was placed at the detector end whilst the electroosmotic flow was reversed by the addition of hexadimethrine bromide (0.001% m/v) to the electrolyte. The three analytes were separated counter to the electroosmotic flow via their interaction with a-cyclodextrin. The methodology realised detection limits (3 x S/N) of 2.5 x 10~7 M for both morphine and oripavine and 5 x 10~7 M for pseudomorphine. The relative standard deviations of the migration times and the peak heights for the three analytes ranged from 0.6 % up to 0.8 % and 1.5% up to 2.1 % respectively. Further improvements were made by incorporating a co-axial sheath flow detection cell. The methodology was validated by comparing the results realised using this technique with those obtained by high performance liquid chromatography (HPLC), for the determination of both morphine and oripavine in seven industrial process liquors. A complimentary capillary electrophoresis procedure with UV-absorption detection was also developed and applied to the determination of morphine, codeine, oripavine and thebaine in nine process liquors. The results were compared with those achieved using a standard HPLC method. Although over eighty papers have appeared in the literature on the analytical applications of acidic potassium permanganate chemiluminescence, little effort has been directed towards identifying the origin of the luminescence. It was found that chemiluminescence was generated during the manganese(III), manganese(IV) and manganese(VII) oxidations of sodium borohydride, sodium dithionite, sodium sulfite and hydrazine sulfate in acidic aqueous solution. From the corrected chemiluminescence spectra, the wavelengths of maximum emission were 689 ± 5 nm and 734 ± 5 nm when the reactions were performed in sodium hexametaphosphate and sodium dihydrogenorthophosphate or orthophosphoric acid environments respectively. The corrected phosphorescence spectrum of manganese(II) sulfate in a solution of sodium hexametaphosphate at 77 K, exhibited two peaks with maxima at 688 nm and 730 nm. The chemical and spectroscopic evidence presented strongly supported the postulation that the emission was an example of solution phase chemically induced phosphorescence of manganese(II). Thereby confirming earlier predictions that the chemiluminescence from acidic potassium permanganate reactions originated from an excited manganese(II) species. Additionally, these findings have had direct analytical application in that manganese(IV) was evaluated as a new reagent for chemiluminescence detection. The oxidations of twenty five organic and inorganic species, with solublised manganese(IV), were found to elicit analytically useful chemiluminescence with detection limits (3 x S/N) for Mn(II), Fe(II), morphine and codeine of 5 x 10-8 M, 2.5 x 10-7 M, 7.5 x 10-8 M and 5 x 10-8M, respectively. The corrected emission spectra from four different analytes gave wavelengths of maximum emission in the range from 733 nm up to 740 nm indicating that these chemiluminescence reactions also shared a common emitting species, excited manganese(II). Whilst several analytical problems were addressed in this thesis and answers to certain questions regarding the fundamentals of acidic potassium permanganate chemiluminescence were proposed, there are several areas that would benefit from further research. These are outlined in the final chapter of this thesis.

Hexavalent chromium in welding fume

Evaluates the current Australian Standard method (AS3853.1) for the determination of total hexavalent chromium (Cr(VI)) in stainless steel welding fume. Investigates the extraction kinetics of this Cr(VI) into a range of media. Develops an analytical method for the determination of Cr(VI) in acidic extract solutions and investigates the extraction of Cr(VI) under simulated in vivo conditions.

An investigation of polypyrrole coated conductive textiles

This research first clarified a possible chemical reaction between a dispersing dye and the conducting polymer polypyrrole. Then, the effect of acidic dyes as dopants on the colours, conductivity and thermal stability of polypyrrole were measured. Finally, the polypyrrole nanoparticles were prepared by a microemulsion polymerisation technique.