Glass transition and free volume behaviour of poly(acrylonitrile)/LiCF3SO3 polymer-in-salt electrolytes compared to poly(ether urethane)/LiClO4 solid polymer electrolytes

Measurements of the glass transition temperature (T_g) and free volume behaviour of poly(acrylonitrile) (PAN) and PAN/lithium triflate (LiTf), with varying salt composition from 10 to 66 wt% LiTf, were made by positron annihilation lifetime spectroscopy (PALS). Addition of salt from 10 to 45 wt% LiTf resulted in an increase in the mean free volume cavity size at room temperature (r.t.) as measured by the orthoPositronium (oPs) pickoff lifetime, τ₃, with little change in relative concentration of free volume sites as measured by oPs pickoff intensity, I₃. The region from 45 to 66 wt% salt displayed no variation in relative free volume cavity size and concentration. This salt concentration range (45 wt%<[LiTf]<66 wt%) corresponds to a region of high ionic conductivity of order 10⁻⁵ to 10⁻⁶ S cm⁻¹ at T_g as measured by PALS. A percolation phenomenon is postulated to describe conduction in this composition region. Salt addition was shown to lower the T_g as measured by PALS; T_g was 115°C for PAN and 85°C for PAN/66 wt% LiTf. The T_g and free volume behaviour of this polymer-in-salt electrolyte (PISE) was compared to a poly(ether urethane)/LiClO₄ where the polymer is the major component, i.e. traditional solid polymer electrolyte (SPE). In contrast to the PISE, the T_g of the SPE was shown to increase with increasing salt concentration from 5.3 to 15.9 wt%. The relative free volume cavity size and concentration at r.t. were shown to decrease with increasing salt concentration. Ionic conductivity in this SPE was of order 10⁻⁵ S cm⁻¹ at r.t., which is over 60°C above T_g, 10⁻⁸ S cm⁻¹ at 25°C above T_g, and conductivity was not measurable at T_g.

Tailoring the surface chemistry of carbon fiber and E-glass composites for improved adhesion

The main challenges in the manufacture of composite materials are low surface energy and the presence of silicon-containing contaminants, both of which greatly reduce surface adhesive strength. In this study, carbon fiber (CF) and E-glass epoxy resin composites were surface treated with the Accelerated Thermo-molecular adhesion Process (ATmaP). ATmaP is a multiaction surface treatment process where tailored nitrogen and oxygen functionalities are generated on the surface of the sample through the vaporization and atomization of n-methylpyrrolidone solution, injected via specially designed flame-treatment equipment. The treated surfaces of the polymer composites were analyzed using XPS, time of flight secondary ion mass spectrometry (ToF-SIMS), contact angle (CA) analysis and direct adhesion measurements. ATmaP treatment increased the surface concentration of polar functional groups while reducing surface contamination, resulting in increased adhesion strength. XPS and ToF-SIMS showed a significant decrease in silicon-containing species on the surface after ATmaP treatment. E-glass composite showed higher adhesion strength than CF composite, correlating with higher surface energy, higher concentrations of nitrogen and CO functional groups (from XPS) and higher concentrations of oxygen and nitrogen-containing functional groups (particularly C₂H₃O⁺ and C₂H₅NO⁺ molecular ions, from ToF-SIMS).

Compressive deformation and damage of Mg-based metallic glass interpenetrating phase composite containing 30-70 vol% titanium

Mg-based metallic glass interpenetrating phase composites (IPCs) containing 30-70 vol% titanium was fabricated in this study. The effects of reinforced phase volume fraction and interspace on the mechanical properties were investigated systematically. With increasing the volume fraction of titanium, the fracture strength and strain increased up to 1860 MPa and 44%, respectively. The results showed that the critical volume fraction (around 40%) of Ti metal should be required for significantly improving plasticity of IPC. Decreasing the interspace of the titanium phase could lead to enhancement of yield and fracture strength. The deformation behavior and strengthening mechanisms were discussed in detail.

Through the looking glass : immersive interfaces for participant engagement in blended e-learning environments

This chapter outlines current research profiling students and educators participating in and constructing immersive interfaces in blended e-learning settings. Multi User Virtual Environments (MUVEs) and real world settings augmented with virtual information can generate problem-solving communities where participants gain greater technical knowledge and skills through meaningful and frequent interaction. MUVEs can also generate technical innovation amongst students from diverse disciplinary backgrounds provided students are encouraged to help each other and learn together. After detailing some false assumptions about computer literacy that can stifle meaningful exploration with new technologies in contemporary education, this chapter documents an exemplar involving extensive collaboration between students from different educational backgrounds with diverse technical competencies. The success of this initiative hinges on the willingness of educators to provide a shared learning experience where technology is used to facilitate increased student communication and offers a site for invention, informed critique, industry participation, and a sense of community.

Possible electrical double-layer contribution to the equilibrium thickness of intergranular Glass films in polycrystalline ceramics

The plausibility of the entropic repulsion of electrical double layers acting to stabilize an equilibrium thickness of intergranular glass films in polycrystalline ceramics is explored. Estimates of the screening length, surface potential, and surface charge required to provide a repulsive force sufficiently large to balance the attractive van der Waals and capillary forces for observable thicknesses of intergranular film are calculated and do not appear to be beyond possibility. However, it has yet to be established whether crystalline particles in a liquid-phase sintering medium possess an electrical double layer at high temperatures. If they do, such a surface charge layer may well have important consequences not only for liquid-phase sintering but also for high-frequency electrical properties and microwave sintering of ceramics containing a liquid phase.