The effect of low cycle fatigue, ratcheting and mean stress relaxation on stress-strain response and microstructural development in a dual phase steel

This study examines the cyclic plastic deformation behavior and microstructural development of a dual phase steel in both symmetric and asymmetric cycling in strain and stress control modes. The low-cycle fatigue (LCF) and mean stress relaxation (MSR) tests show very similar fatigue lifetimes. However, fatigue lifetimes reduce and prominent accumulation of directional strain was observed in ratcheting. A microstructural analysis has revealed that the type of cyclic test carried out has a noticeable impact on the substructural development, and this has been correlated with differences in accumulated tensile strain. Electron backscatter diffraction investigation has shown larger in-grain misorientation for ratcheting specimen in comparison with LCF and MSR specimens. The orientation of ferrite grains was found to have very little effect on their substructural development, and strain localization commonly occurred in the ferrite at the ferrite/martensite interface.

Effect of martensite morphology on low cycle fatigue behaviour of dual phase steels: Experimental and microstructural investigation

The low cycle fatigue (LCF) behaviour of a dual phase (DP) steel with different martensite morphologies has been investigated in the present work. DP steels with coarse martensite morphologies show inferior LCF life in comparison with fine martensite morphologies for all martensite volume fractions examined. It is suggested that this is be due to the development of larger local plastic strain concentrations in the ferrite with a coarser microstructure, compared to the finer microstructural morphology. Fatigue cracks were observed to initiate inside ferrite grains, and to preferentially propagate through the softer ferrite phase. The average sub-cell size was finer in samples with higher martensite volume fractions, but the sub-cell size was almost unaffected by the martensite morphology.

Bimodal grain size distributions in UFG materials produced by SPD - their evolution and effect on the fatigue and monotonic strength properties

In ultrafine-grained (UFG) materials produced by severe plastic deformation (SPD) techniques such as ECAP (equal channel angular pressing), bimodal grain size distributions have been observed under different circumstances, for example shortly after ECAP, after rest or anneal and/or after mild cyclic deformation at rather low homologous temperature. It has been shown that the mechanical monotonic and fatigue properties of some UFG materials can be modified (sometimes enhanced) by introducing a bimodal grain size distribution by a mild annealing treatment which leads, in some cases, to a good combination of strength and ductility. Here, the conditions under which bimodal grain size distributions evolve by (adiabatic) heating during ECAP and during subsequent annealing or cyclic deformation will be explored, and the effects on the mechanical properties, as studied by the authors and as reported so far in the literature, will be reviewed and discussed. In particular, the role of temperature rise during ECAP will be considered in some detail.

Cyclic carbonate–sodium smectite intercalates

Five-membered cyclic organic carbonates (COC) are of interest for their ability to modify the surface properties of smectites and enhance the hydraulic resistance of bentonites to saline leachates. The mechanism of interaction of glycerol carbonate (GC) and several other hydroxyl containing cyclic organic carbonates (generally having progressively greater molecular masses) with sodium montmorillonite (Na+-Mt) was studied using powder X-ray diffraction and infrared spectroscopy. The 001 reflection for GC/Na+-Mt intercalates varied with the amount COC added, and the measured d001 value increased from 1.29 nm to as large as 2.22 nm at equal-mass coverage of the COC to Na+-Mt. In general, when intercalated, the cyclic carbonyl (Cdouble bond; length as m-dashO) stretch and the fundamental hydroxyl (O–H) stretch bands of COC derivatives were red-shifted with respect to these bands for neat COC, indicating strong ion-dipole interaction of the carbonyl group with interlayer Na+, and H-bonding of the OH group with both interlayer water and Mt surfaces. A stable and highly ordered intercalate was produced at a 1:1 mass loading with Mt in which about 6 GC molecules per unit cell (~ 7 molecules per Na+ ion) replaced most of the interlayer water.