Effect of second-phase particles on shape memory in Fe-Mn-Si-based alloys

The shape memory behaviour of two Fe–Mn–Si-based alloys has been investigated. One alloy was a reference alloy, and the other alloy was
similar in composition except that it contained 0.55 wt% Ti. Following solution treatment and quenching, strip samples were subjected to three types
of treatments; isothermal holding, cold rolling followed by isothermal holding, and hot rolling followed by isothermal holding. These treatments
resulted in the formation of intermetallic precipitates in the Ti-containing alloy, while the reference alloy remained precipitate-free. In comparing
the shape memory of the reference and the particle-containing alloy after identical heat treatments, it was found that the formation of precipitates
had a beneficial effect on the shape memory in all cases. In general, the larger precipitates caused a larger increase in the shape memory. The effect
of particle size on shape memory has been analysed using the current data and published results for a range of precipitate types.

Thermo-mechanical processing and the shape memory effect in an Fe–Mn–Si-based shape memory alloy

The effect of cold rolling and annealing on the shape memory effect (SME) in an Fe–Mn–Si-based alloy has been studied. It has been found
that the SME in these alloys can be significantly increased by the appropriate thermo-mechanical processing (TMP). The optimum conditions
were found to be 15% cold rolling followed by annealing at 800 ◦C for 15 min. This produced a total strain recovery of 4.5%. TEM showed that
this processing schedule produces a microstructure of evenly spaced, and well defined stacking faults throughout the parent phase. It is shown for
the first time that samples processed in this way produce a larger fraction of martensite compared to samples in the as-austenitized condition. It
is concluded that the stacking faults induced by TMP act as nucleation sites for martensite formation during deformation. The SME is improved
primarily as a result of the increased amount of martensite that is formed in this condition.

Effect of NbC and TiC precipitation on shape memory in an iron-based alloy

This paper examines the effects of TiC and NbC precipitation and prior cold rolling on the shape memory behaviour of an iron-based alloy. A precipitate-free alloy was used as a reference to investigate the relative contributions of prior-deformation and precipitation on shape memory. Heat treatment of the Nb- and Ti-containing alloys at 700 °C and 800 °C resulted in carbide precipitates between 120 nm and 220 nm in diameter. Bend testing of these samples showed a marginal increase in shape memory compared to the precipitate-free alloy. Under these conditions TiC precipitation exhibited slightly better shape memory than for NbC. However, this small increase was over-shadowed by the marked increase in shape memory that can be produced by subjecting the alloys to cold rolling followed by recovery annealing. When processed in this way, fine carbides are formed in the Ti- and Nb-containing alloys during the heat treatment. For particles >25 nm in diameter the shape memory is unaffected, but, it was found that small <5 nm particles have a detrimental effect on shape memory due to pinning of the martensite plates, thereby inhibiting their reversion to austenite. The optimum shape memory was observed in the precipitate-free alloy after cold rolling and recovery annealing.

Processing and mechanical properties of porous titanium-niobium shape memory alloy for biomedical applications

Ti-26 at.%Nb (hereafter Ti-26Nb) alloy foams were fabricated by space-holder sintering process. The porous structures of the foams were characterized by scanning electron microscopy (SEM). The mechanical properties of the Ti-26Nb foam samples were investigated using compressive test. Results indicate that mechanical properties of Ti-26Nb foam samples are influenced by foam porosity. The plateau stresses and elastic moduli of the foams under compression decrease with the increase of their porosities. The plateau stresses and elastic moduli are measured to be from 10~200 MPa and 0.4~5.0 GPa for the Ti-26Nb foam samples with porosities ranged from 80~50 %, respectively.

Nanofretting behaviors of NiTi shape memory alloy

Nanofretting refers to cyclic movements of contact interfaces with the relative displacement amplitude at the nanometer scale, where the contact area and normal load are usually much smaller than those in fretting. Nanofretting widely exists in microelctromechanical systems (MEMS) and may become a key tribological concern besides microwear and adhesion. With a triboindenter, the nanofretting behaviors of a nickel titanium (NiTi) shape memory alloy are studied under various normal loads (1–10 mN) and tangential displacement amplitudes (2–500 nm) by using a spherical diamond tip. Similar to fretting, the nanofretting of NiTi/diamond pair can also be divided into different regimes upon various shapes of tangential force–displacement curves. The dependence of nanofretting regime on the normal load and the displacement amplitude can be summarized in a running condition nanofretting map. However, due to the surface and size effects, nanofretting operates at some different conditions, such as improved mechanical properties of materials at the nanometer scale, small apparent contact area and single-asperity contact behavior. Consequently, different from fretting, nanofretting was found to exhibit several unique behaviors: (i) the maximum tangential force in one cycle is almost unchanged during a nanofretting test, which is different from a fretting test where the maximum tangential force increases rapidly in the first dozens of cycles; (ii) the tangential stiffness in nanofretting is three orders magnitude smaller than that in fretting; (iii) the friction coefficient in nanofretting is much lower than that in fretting in slip regime; (iv) no obvious damage was observed after 50 cycles of nanofretting under a normal load of 10 mN.

TiNi shape memory alloy foams synthesized by spacer sintering and their properties

Titanium (Ti) and nickel (Ni) elemental powders were blened by ball milling and the ball milled powders were employed to fabricate NiNi shape memory alloy (SMA) foams by space sintering. Effect of ball milling time on phase constitutes of the sintered TiNi alloy foams was studied by X-ray diffraction (XRD) analysis.Scanning election microscopy (SEM) was used to characterize the porous structure, and compressive tests were carried out to evaluate the mechanical properties of the foams. Results indicate the porosities of the TiNi alloy foams can be controlled by using the spacer sincering method, and the porosities show a significant effect on the mechanical prperties and shape memory effect (SME).

Shape memory alloy scaffolds for bone tissue engineering

Titanium alloy scaffolds for bone tissue engineering are receiving increasing attention because their porous structure and mechanical properties can be adjusted to match those of bone. In particular, there is an enormous potential to increase the life of such implant material if the porous structure can be imparted with shape memory properties. In the present study, TiNi scaffolds with a porous structure and high porosities up to 75% were fabricated by powder metallurgy. The porous structure was characterized by scanning electron microscope. The mechanical properties, the shape memory and superelastic effects were investigated by differential scanning calorimetry, nanoindentation and compressive tests. Results indicate that the porous TiNi scaffolds display an open-cell porous structure which provides new bone tissue ingrowth ability. The mechanical properties of the TiNi scaffolds can be tailored to match those of natural bone. Furthermore, the TiNi scaffolds show good shape memory and superelastic effects.

Titanium–nickel shape memory alloy foams for bone tissue engineering

Titanium–nickel (TiNi) shape memory alloy (SMA) foams with an open-cell porous structure were fabricated by space-holder sintering process and characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. The mechanical properties and shape memory properties of the TiNi foam samples were investigated using compressive test. Results indicate that the plateau stresses and elastic moduli of the foams under compression decrease with the increase of their porosities. The plateau stresses and elastic moduli are measured to be from 1.9 to 38.3 MPa and from 30 to 860 MPa for the TiNi foam samples with porosities ranged from 71% to 87%, respectively. The mechanical properties of the TiNi alloy foams can be tailored to match those of bone. The TiNi alloy foams exhibit shape memory effect (SME), and it is found that the recoverable strain due to SME decreases with the increase of foam porosity.

Influence of porosity on shape memory behavior of porous TiNi shape memory alloy

Porous Ti-50.5at.%Ni shape memory alloy (SMA) samples with a range of  porosities were prepared by spacer sintering. The porous structure of the alloy was examined using scanning electron microscopy (SEM). The phase constituents of the porous TiNi alloy were determined by X-ray diffraction (XRD). The shape memory behavior of the porous TiNi alloy was investigated using loading–unloading compression tests. Results indicate that the porous TiNi alloy exhibits superelasticity and the recoverable strain by the superelasticity decreases with the increase of porosity. After a prestrain of 7%, the superelastically recovered strains for the porous TiNi alloy samples with porosities of 46%, 59%, 69% and 77% are 2.0%, 1.8%, 1.5% and 1.3%, respectively. The pores in the TiNi alloy samples cause stress/strain concentration, as well as crack initiation, which adversely affect the shape memory behavior of the porous TiNi alloy.