Effect of cooling rate on phase transformations in a high-strength low-alloy steel studied from the liquid phase

The phase transformation and precipitation in a high-strength low-alloy steel have been studied over a large range of cooling rates, and a continuous cooling transformation (CCT) diagram has been produced. These experiments are unique because the measurements were made from samples cooled directly from the melt, rather than in homogenized and re-heated billets. The purpose of this experimental design was to examine conditions pertinent to direct strip casting. At the highest cooling rates which simulate strip casting, the microstructure was fully bainitic with small regions of pearlite. At lower cooling rates, the fraction of polygonal ferrite increased and the pearlite regions became larger. The CCT diagram and the microstructural analysis showed that the precipitation of NbC is suppressed at high cooling rates, and is likely to be incomplete at intermediate cooling rates.

Influence of cooling rate on the microstructure and corrosion behavior of Al-Fe alloys

The effect of Fe in Al is technologically important for commercial Al-alloys, and in recycled Al. This work explores the use of the novel rapid solidification technology, known as direct strip casting, to improve the recyclability of Al-alloys. We provide a comparison between the corrosion and microstructure of Al-Fe alloys prepared with wide-ranging cooling rates (0.1. °C/s to 500. °C/s). Rapid cooling was achieved via direct strip casting, while slow cooling was achieved using sand casting. Corrosion was studied via polarisation and immersion tests, followed by surface analysis using scanning electron microscopy and optical profilometry. It was shown that the corrosion resistance of Al-Fe alloys is improved with increased cooling rates, attributed to the reduced size and number of Fe-containing intermetallics.

Performance assessment of earth pipe cooling system for low energy buildings in a subtropical climate

Energy consumption in heating and cooling around the world has been a major contributor to global warming. Hence, many studies have been aimed at finding new techniques to save and control energy through energy efficient measures. Most of this energy is used in residential, agricultural and commercial buildings. It is therefore important to adopt energy efficiency measures in these buildings through new technologies and novel building designs. These new building designs can be developed by employing various passive cooling systems. Earth pipe cooling is one of these which can assist to save energy without using any customary mechanical units. This paper investigates the earth pipe cooling performance in a hot humid subtropical climate of Rockhampton, Australia. A thermal model is developed using ANSYS Fluent for measuring its performance. Impacts of air velocity, air temperature, relative humidity and soil temperature on room cooling performance are also assessed. A temperature reduction of around 2 °C was found for the system. This temperature reduction contributed to an energy saving of a maximum of 866.54 kW (8.82%) per year for a 27.23 m3 room.

Numerical modeling of vertical earth pipe cooling system for hot and humid subtropical climate

Energy crisis is one of the major problems facing the progress of human society. There are several energy-efficient technologies that can be applied to save energy and make a sustainable environment. Passive air cooling of earth pipe cooling technology is one of them to reduce the energy consumption for hot and humid subtropical climates. The technology works with a long buried pipe with one end for intake air and the other end for providing air cooled by soil to the desired space such as residential, agricultural, or industrial buildings. It can be an attractive economical alternative to conventional cooling since there are no compressors or any customary mechanical unit. This chapter reports the performance of a vertical earth pipe cooling system for a hot and humid subtropical climatic zone in Queensland, Australia. A series of buried pipes were installed in vertical arrangement in order to increase earth pipe cooling performance. To measure the performance of the system, a numerical model was developed and simulated using the CFD software Fluent in ANSYS 15.0. Data were collected from two modeled rooms built from two shipping containers and installed at the Sustainable Precinct at Central Queensland University, Rockhampton, Australia. The impact of air temperature and velocity on room cooling performance has also been assessed. A temperature reduction of 1.82 °C was observed in the room connected to the vertical earth pipe cooling system, which will save the energy cost for thermal cooling in buildings.

Erratum: selection of suitable passive cooling strategy for a subtropical climate

In the original version of this article (Ahmed et al. 2014), the authors noted that the author list was published with errors. The correct author list can be found in this erratum. The publisher would like to apologise to the authors for this error.

Investigation on decomposition behavior of austenite under continuous cooling in vanadium microalloyed steel (30MSV6)

In the present study, investigations are focused on microstructural evolution and the resulting hardness during continuous cooling transformation (CCT) in a commercial vanadium microalloyed steel (30MSV6). Furthermore, the effects of cooling rate and austenite grain size (AGS) on CCT behavior of the steel have been studied by employing high-resolution dilatometry. Quantitative metallography accompanied with scanning electron microscopy (SEM) has efficiently confirmed the dilatometric measurements of transformation kinetics and austenite decomposition products. A semi-empirical model has been proposed for prediction of microstructural development during austenite decomposition of the steel and the resultant hardness. The model consists of 8 sub-models including ferrite transformation start temperature, ferrite growth, pearlite start temperature, pearlite growth, bainite start temperature, bainite growth, martensite start temperature and hardness. The transformed fractions of ferrite, pearlite and bainite have been described using semi-empirical Johnson-Mehl-Avrami-Kolmogorov (JMAK) approach in combination with Scheil's equation of additivity. The JMAK rate parameter for bainite has been formulated using a diffusion-controlled model. Predictions of the proposed model were found to be in close agreement with the experimental measurements.

Integrated model of horizontal earth pipe cooling system for a hot humid climate

Energy efficiency of a building has become a major requirement since the building sector produces 40%-50% of the global greenhouse gas emissions. This can be achieved by improving building’s performance through energy savings, by adopting energy efficient technologies and reducing CO2 emissions. There exist several technologies with less or no environmental impact that can be used to reduce energy consumption of the buildings. Earth pipe cooling system is one of them, which works with a long buried pipe with one end for intake air and the other end for providing air cooled by soil to the building. It is an approach for cooling a room in a passive process without using any habitual mechanical unit. The paper investigates the thermal performance of a horizontal earth pipe cooling system in a hot and humid subtropical climatic zone in Queensland, Australia. An integrated numerical model for the horizontal earth pipe cooling system and the room (or building) was developed using ANSYS Fluent to measure the thermal performance of the system. The impact of air temperature, soil temperature, air velocity and relative humidity on room cooling performance has also been assessed. As the soil temperature was below the outdoor minimum temperature during the peak warming hours of the day, it worked as an effective heat sink to cool the room. Both experimental and numerical results showed a temperature reduction of 1.11oC in the room utilizing horizontal earth pipe cooling system which will assist to save the energy cost in the buildings.

Parametric study on thermal performance of horizontal earth pipe cooling system in summer

Rational use of energy and its associated greenhouse gas emissions has become a key issue for a sustainable environment and economy. A substantial amount of energy is consumed by today's buildings which are accountable for about 40% of the global energy consumption. There are on-going researches in order to overcome these and find new techniques through energy efficient measures. Passive air cooling of earth pipe cooling technique is one of those which can save energy in buildings with no greenhouse gas emissions. The performance of the earth pipe cooling system is mainly affected by the parameters, namely air velocity, pipe length, pipe diameter, pipe material, and pipe depth. This paper investigates the impact of these parameters on thermal performance of the horizontal earth pipe cooling system in a hot humid subtropical climate at Rockhampton, Australia. For the parametric investigation, a thermal model was developed for the horizontal earth pipe cooling system using the simulation program, FLUENT 15.0. Results showed a significant effect for air velocity, pipe length, and pipe diameter on the earth pipe cooling performance, where the pipe length dominated the other parameters.

One-way water-transport cotton fabrics with enhanced cooling effect

Two types of directional water transport fabrics are prepared by using cotton fabric as substrate and an electrospraying technique to apply a hydrophobic coating on one side of the fabric. The main difference between the two electrosprayed fabrics is that one of them was precoated with a hydrophilic thermoconductive resin over the fiber surface prior to electrospraying. As a result, the precoated fabric has a much higher thermoconductivity than the other, while they are similar in water transport and fibrous structure. In the wet state, the directional water-transport fabrics generate a temperature difference between the two fabric sides while drying naturally. The fabric with higher thermal conductivity shows smaller temperature difference, better thermal transfer within the fabric, stronger evaporation cooling effect, and accelerated moisture evaporation. Directional water transport fabrics with high thermal conductivity may be used to mitigate thermal burden in sportswear, summer clothing, medical fabrics, and workwear.

Active cooling and low carbon comfort

Within the debate about fostering more sustainable built environments one of the key battlegrounds surrounds thermal comfort, and in particular the use of air conditioning. In the search for less energy-intensive alternatives, a renewed interest has emerged around the design vocabulary of ‘passive cooling’. The paper argues that the terminology of passive/active needs inverting for such approaches to gain wider support as a viable alternative to mechanical cooling.

It is argued that non-air-conditioned buildings actively engage with their environments and that the current notion of passive cooling leaves us blind to the ways occupants, buildings and the material culture of interior spaces are all entangled in relations that enable thermal comfort to be actively achieved and maintained. To present this argument for re-categorising low-carbon architecture design as active cooling, the paper draws on the concept of entanglement.