A calibration for surface analysis on aluminium alloys by RF-Glow-Discharge Optical Emission Spectrometry

Glow-Discharge Optical Emission Spectrometry (GD-OES) is a powerful technique for the rapid analysis of elements in a solid surface as a function of depth. DC-GD-OES allows depth profiling on electrically conductive surfaces only, and has proven to be difficult for the analysis of insulating layers, such as oxides. However, the technique of radio-frequency (RF) GD-OES has the advantage of being able to depth profile through multiple layers, both conducting and insulating. In this work, a LECO GDS- 850A spectrometer was calibrated for aluminium, oxygen, and other elements, with the RF source installed. A quantitative depth profile for a sample of tempered aluminium alloy 7475 is presented and compared with earlier work[1,2].

Effect of composition on the texture and deformation behaviour of wrought Mg alloys

The microstructure and mechanical response of three extruded magnesium alloys, Mg-3Al-1Zn (AZ31), Mg-1.5Mn (Ml) and Mg-lMn-0.4RE (ME10) are examined. The tensile yield strength of ME10 was nearly half that of AZ31 and Ml. The tensile elongations were 6%, 11% and 19% for Ml, AZ31 and ME10, respectively. This range of properties is large and is attributed to the unique extrusion texture produced in ME10, and the high density of fine particles in Ml.

The origin of "Rare Earth" texture development in extruded Mg-based alloys and its effect on tensile ductility

The extrusion behaviour, texture and tensile ductility of five binary Mg-based alloys have been examined and compared to pure Mg. The five alloying additions examined were Al, Sn, Ca, La and Gd. When these alloys are compared at equivalent grain size, the La- and Gd-containing alloys show the best ductilities. This has been attributed to a weaker extrusion texture. These two alloying additions, La and Gd, were found to also produce a new texture peak with View the MathML source parallel to the extrusion direction. This “rare earth texture” component was found to be suppressed at high extrusion temperatures. It is proposed that the View the MathML source texture component arises from oriented nucleation at shear bands.

Effect of surface roughness of Ti, Zr, and TiZr on apatite precipitation from simulated body fluid

Some of the critical properties for a successful orthopedic or dental implant material are its biocompatibility and bioactivity. Pure titanium (Ti) and zirconium (Zr) are widely accepted as biocompatible metals, due to their non-toxicity. While the bioactivity of Ti and some Ti alloys has been extensively investigated, there is still insufficient data for Zr and titanium-zirconium (TiZr) alloys. In the present study, the bioactivity, that is, the apatite forming ability on the alkali and heat treated surfaces of Ti, Zr, and TiZr alloy in simulated body fluid (SBF), was studied. In particular, the effect of the surface roughness characteristics on the bioactivity was evaluated for the first time. The results indicate that the pretreated Ti, Zr and TiZr alloy could form apatite coating on their surfaces. It should be noted that the surface roughness also critically affected the bioactivity of these pretreated metallic samples. A surface morphology with an average roughness of approximately 0.6 microm led to the fastest apatite formation on the metal surfaces. This apatite layer on the metal surface is expected to bond to the surrounding bones directly after implantation.

Effect of microalloying with rare-earth elements on the texture of extruded magnesium-based alloys

A series of alloys have been produced with microalloying additions of rare-earth (RE) elements in the range of 0.1–0.4 wt.%. The alloys have been extruded to produce grain sizes of 23 ± 5 μm. The texture of the extruded alloys was measured, and it was found that the extrusion texture was weakened by the addition of RE elements. The samples with weakened extrusion textures exhibited an increase in the tensile elongation.

Re-examination of the effect of NbC precipitation on shape memory in Fe-Mn-Si-based alloys

Current literature pertaining to the shape memory effect in the Fe–Mn–Si-based system is critically discussed. It is argued that the
enhanced shape memory previously attributed to NbC precipitation is mainly due to the associated thermo-mechanical treatments.
It is concluded that the thermo-mechanical processing of the alloy is the dominant factor that determines the shape memory effect in
this alloy system.

Texture and mechanical anisotropy in three extruded magnesium alloys

One ZM61 alloy (6·2%Zn, 1·2%Mn) and two magnesium alloys containing nominally 3% of neodymium and yttrium respectively have been prepared in the form of hot extruded flat strips. Their textures and microstructures have been quantified and series of mechanical tests were carried out to determine plane stress yield loci in both the solution treated and aged conditions. The ZM61 alloy had a sharp texture and marked anisotropy of strength that could be rationalised in terms of deformation by basal <a> slip and {1012}<1011> twinning. This material was much weaker in compression than in tension. Precipitation hardening on aging caused a greater impedance to twinning than to slip with the result that the anisotropy was somewhat reduced. The Mg–3Nd alloy had a very weak and different texture but nevertheless demonstrated a pronounced anisotropy of strength. Aging increased the yield stress by about 80% and also inhibited twinning to some extent although the degree of anisotropy remained almost unaffected. The Mg–3Y alloy which showed a texture of intermediate strength was different in type from either of the others. Its strength behaviour was close to isotropic; in particular, no difference existed between tensile and compressive loading, and aging produced only a marginal increase in strength. Twins were relatively infrequent in the deformed Mg–3Y alloy but its mechanical behaviour could not be rationalised according to simple models.

Biomimetic processing of nanocrystallite bioactive apatite coating on titanium-zirconium alloy

In this paper nanocrystallite apatite coating on TiZr substrate was prepared by a biomimetic process. Surface morphology, thickness, crystalline phases a~nd bond strength of the coating were investigated by SEM, XRD and tensIle test, respectively. Results show that the apatite coating exhibIts a nanocrystalIite structure with similar stoichiometry to that of natural bone. The apatite layer becomes thicker with the increasing of the SBF immersion time and is firmly adhered to the substrate with the highest average bond strength of 15.5 MPa. This nanocrystallite apatite coating is expected to bond to surrounding bone tissue directly in vivo after implantation.

Some issues relating to the ductility of wrought magnesium alloys

The present work is concerned with gaining a better understanding of the factors that control the ductility of wrought magnesium alloys. The ultimate aim is to develop alloys with vastly improved room temperature formability. It is shown that 3D tomography of fractured tensile specimens reveals disk shaped voids aligned more or less at 45 deg. to the tensile axis. These voids are consistent with twin induced void formation. It is also shown that the double twins that produce such voids form in contradiction to Schmid predictions. Finally, it is demonstrated that low levels of rare-earth additions leads to vastly improved texture and ductility in extrusions, as they do in rolled sheet.

The microstructure evolution and mechanical properties of cryorolled Al alloys

A solutionized Al2024 alloy was subjected to rolling at liquid nitrogen temperature (cryorolling) resulting in an ultra-fine stmcture. The material was also subjected to recovery annealing at 160°C. The ultrafine structured material demonstrated increased strength but very low ductility. The uniform elongation of the material after recovery annealing increased without any sacrifice of strength.

Nature of new order rights to minerals : a rubikian exercise since passing the mayday rubicon with a cubic zirconium?

The Mineral and Petroleum Resources Development Act 28 of 2002 has created new categories of rights to "minerals" that may be granted to applicants by the Minister of Minerals and Energy. In this article the nature of these rights will be examined. The legislature has labelled prospecting rights and mining rights to minerals as limited real rights in the MPRD Act. The remaining rights to minerals are not labelled. Provision is made for registration or recording rights in the revived Mining Titles Registration Act 16 of 1967 (as amended). Registered rights are claimed to constitute a limited real right binding against third parties. Discrepancies and contradictions regarding the nature of rights to minerals are created by the two statutes. It is concluded that only upon clarification of the provisions of the two sister statutes, would the nature of rights to minerals be more evident. The proposed amendment of section 5(1) of the MPRD Act would be in line with property doctrine based upon the common law and is to be welcomed.

In vitro cytotoxicity of binary TI alloys for bone implants

Interest in using titanium (Ti) alloys as load-bearing implant materials has increased due to their high strength to weight ratio, lower elastic modulus, and superior biocompatibility and enhanced corrosion resistance compared to conventional metals such as stainless steel and Co-Cr alloys. In the present study, the in vitro cytotoxicity of five binary titanium alloys, Ti15Ta, Ti15Nb, Ti15Zr, Ti15Sn and Ti15Mo, was assessed using human osteosarcoma cell line, SaOS-2 cells. The Cell proliferation and viability were determined, and cell adhesion and morphology on the surfaces of the binary Ti alloys after cell culture were observed by SEM. Results indicated that the Ti binary alloys of Ti15Ta, Ti15Nb and Ti15Zr exhibited the same level of excellent biocompatibility; Ti15Sn alloy exhibited a moderate biocompatibility while Ti15Mo alloy exhibited a moderate cytotoxicity. The SaOS-2 osteoblast-like cells had flattened and spread across the surfaces of the Ti15Ta, Ti15Nb, Ti15Zr and Ti15Sn groups; however, the cell shapes on the Ti15Mo alloy was shrinking and unhealthy. These results indicated that the Mo contents should be limited to a certain level in the design and development of new Ti alloys for implant material applications.

Optimization of alloy design and hot rolling conditions for shape memory in Fe–Mn–Si-based alloys

The effect of composition and hot rolling conditions on the shape memory effect (SME) in the Fe–Mn–Si-based system has been studied to obtain improved shape memory without the need to rely on “training”. It has been found that the texture is not markedly affected by rolling conditions, and texture is therefore not a major factor in explaining variations in SME with processing conditions. Decreasing the pre-deformation temperature to below the Ms was found to have a beneficial effect on shape memory. It was found that the best SME was achieved in an alloy that had Ms just above room temperature, and had been processed by hot rolling followed by recovery annealing. Alloys of different compositions exhibited different optimum rolling temperatures for maximum shape memory performance.

Effect of second-phase particles on shape memory in Fe-Mn-Si-based alloys

The shape memory behaviour of two Fe–Mn–Si-based alloys has been investigated. One alloy was a reference alloy, and the other alloy was
similar in composition except that it contained 0.55 wt% Ti. Following solution treatment and quenching, strip samples were subjected to three types
of treatments; isothermal holding, cold rolling followed by isothermal holding, and hot rolling followed by isothermal holding. These treatments
resulted in the formation of intermetallic precipitates in the Ti-containing alloy, while the reference alloy remained precipitate-free. In comparing
the shape memory of the reference and the particle-containing alloy after identical heat treatments, it was found that the formation of precipitates
had a beneficial effect on the shape memory in all cases. In general, the larger precipitates caused a larger increase in the shape memory. The effect
of particle size on shape memory has been analysed using the current data and published results for a range of precipitate types.