Characteristics of electron beam welded Ti & Ti alloys

Similar and dissimilar butt joint welds comprising combinations of commercially pure grade 4 titanium (CP-Ti), Ti-6Al-4V (Ti-64) and Ti-5Al-5V-5Mo-3Cr (Ti-5553) were created using the electron beam process. The resultant welds were studied by means of metallography, optical microscopy, mechanical testing and scanning electron microscopy. Mechanical testing was performed on welded samples to study the joint integrity and fracture characteristics. A scanning electron microscope investigation was performed on the fracture surface to reveal their fracture modes. While all weldments were crack free and most weldments exhibited mechanical properties comparable to the base metal, negligible ductility was exhibited during tensile testing joints of Ti- 5553 welded to either Ti-64 or Ti-5553.

Study of phase transformation and work hardening phenomenon during drilling of Ti-5553 and Ti-64

Titanium 5553 is a recently developed modification of Russian near-β titanium alloy VT-22 which has applications and potential particularly in the aerospace industry for such key components as landing gear. However, indications are that Ti-5553 has poorer machinability characteristics than other Ti alloys and a comprehensive and far-reaching analysis is a necessary research imperative. This paper presents the result of phase transformation and work hardening during drilling of Ti-5553 compared with Ti-64. The aim of this research work is to optimise the machining condition for Ti-5553, in which the β to a phase transformation, together with material work hardening could be fully understood. Analysis of machinability indicators, such as subsurface micrograph and hardness of drilled samples and drilling forces and torques, demonstrated that Ti-5553 generally has poorer machinability characteristics than Ti-64 and to some extent this variation has been quantified to allow for further and more detailed investigation.

Direct measurement of surface forces between sapphire crystals in aqueous solutions

Measurements are presented of the electrical double layer and van der Waals forces between the (0001) surfaces of two single-crystal sapphire platelets immersed in an aqueous solution of NaCl at pH values from 6.7 to 11. The results fit the standard Deryaguin-Landau-Verwey-Overbeek (DLVO) theory, with a Hamaker constant of 6.7 × 10−20 J. These are the first measurements made using the Israelachvili surface forces apparatus without mica as a substrate material, and they demonstrate the possibility of using this technique to explore the surface chemistry of a wider range of materials.

Measuring surface forces to explore surface chemistry : mica, sapphire and silica

In this paper measurements of the forces acting between two solid surfaces separated by a thin liquid film are discussed. By investigating these forces in a range of different liquids and solutions, it is possible to acquire an understanding of the surface properties of the solid material. The surface of mica has been studied extensively in this way, and the results obtained are reviewed to illustrate how the surface force measurements can give surface chemical information. Recent measurements on two other materials, sapphire and silica, which are of greater practical interest are also discussed.

Deformation induced phase transformation during machining of Ti-5553

Ti-5553 is a relatively new titanium alloy with applications particularly in the aerospace industry for such key structural components as landing gear. However, during machining of Ti-5553, the elevated temperature and high strain at tool-workpiece interface may alter workpiece microstructure and result in ß to a phase transformation. During phase transformation, some intermediated phase such as w phase may form which is brittle and hard to machine, and it could reduce the fatigue life of machined components. The aim of this research work is to optimize the machining condition for Ti-5553, in which its hot deformation behavior in terms of ß to a phase transformation could be fully understood. Analysis of variables such as micrographs of phase components and cutting zone temperature demonstrates that the cutting temperature governs the formation of final phase components and to some extent this variation has been quantified to allow for further and more detailed investigation.

Tribological behaviour of pure Ti with a nanocrystalline surface layer under different loads

Surface mechanical attrition treatment (SMAT), a novel surface severe plastic deformation method, was carried out for titanium (Ti) to create a gradient-structured Ti (SMAT Ti). The tribological behaviour was studied under different loads and dry sliding conditions. The results showed that the deformation layer of SMAT Ti was about 160 μm. The friction and wear results showed that the wear resistance of SMAT Ti was enhanced compared to the coarse-grained (CG) counterpart. SMAT Ti showed abrasive wear under 1 and 5 N, and exhibited abrasive and adhesive wear under 2 N. While CG Ti showed abrasive and adhesive wear under 1-2 N, and exhibited abrasive wear under 5 N for the work hardening effects.

Wear behaviour of pure Ti with a nanocrystalline surface layer

A nanocrystalline (NC) layer with the thickness of 30 µm was produced on pure titanium surface by surface mechanical attrition treatment (SMAT). Microstructure observation indicated that the grain size increases with depth from the treated surface. The friction coefficient decreases and the wear resistance increases with the SMAT sample as compared to its coarse-grained counterpart. The improvement of the wear properties could be attributed to the higher hardness of SMAT sample.

The biomedical application of Ti after severe plastic deformation and thermal oxidation, especially the friction and wear properties of Ti

Surface mechanical attrition treatment (SMAT), a novel surface severe plastic deformation method, was carried out for titanium (Ti) to create a gradient-structured Ti (SMAT Ti). The tribological behaviour was studied under different loads and dry sliding conditions. The results showed that the deformation layer of SMAT Ti was about 160 lm. The friction and wear results showed that the wear resistance of SMAT Ti was enhanced compared to the coarse-grained (CG) counterpart. SMAT Ti showed abrasive wear under 1 and 5 N, and exhibited abrasive and adhesive wear under 2 N. While CG Ti showed abrasive and adhesive wear under 1–2 N, and exhibited abrasive wear under 5 N for the work hardening effects.