Sheared edge quality in the trimming of sheet metals

Examines the sheared edge quality of different automotive sheet metals resulting from the trimming process using experimental tooling and finite element modelling. The significant differences in burr, sliver and edge profile formation have been explained in terms of the strain distribution and tensile properties of the materials.

Investigation on the forming behaviour of metal/polymer laminates

A metal/polymer laminate is a new light weight sheet material suitable to replace conventional steel or aluminium sheet in future car designs. In this study the effect of material composition and process conditions on the forming behaviour of metal/polymer laminates in sheet metal forming was investigated by experimental, analytical and numerical methods.

Tool wear analysis in sheet metal stamping

This thesis advances the understanding of die wear in sheet metal stamping. It was found that transient conditions exist at the die radius, resulting in severe contact pressures that are critical to the wear behaviour. The findings challenge applicability of traditional wear tests and models for sheet metal stamping processes.

Sliding distance, contact pressure and wear in sheet metal stamping

This paper directly examines the contact sliding distance experienced during a typical sheet metal stamping process-an area that has largely been neglected in the literature. A method to numerically quantify the sliding distance is proposed. The sliding distance predicted from this method, and the contact pressure obtained from numerical simulation, allow the recently identified time-dependent contact conditions on the die and blank surfaces to be completely characterized. Consequently, a new insight into the wear/galling that occurs at the die radius in sheet metal stamping is gained. The results show that the region close to zero degrees on the die radius is likely to experience the most wear, with the identified transient stage contributing to a large proportion of the total wear. Additionally, the region on the blank surface often observed to be heavily burnished - the die impact line - is estimated to experience the highest wear severity due to the transient contact conditions. The proposed method to numerically quantify the sliding contact conditions can be applied as a general approach to study any other two-body sliding contact situations.

Effects of temperature in relation to sheet metal stamping

The demand to reduce the use of lubricants and increase tool life in sheet metal stamping has resulted in increased research on the sliding contact between the tool and the sheet materials. Unlubricated sliding wear tests for soft carbon steel sliding on D2 tool steel were performed using a pin-on-disk tribometer. The results revealed that temperature has an influencing role in the wear of tool steel and that material transfer between tool and sheet can be minimized at a certain temperature range in sheet metal stamping.

Tool wear in sheet metal stamping

This paper discusses our recent research on wear at the die radius in sheet metal stamping. According to wear theory, contact pressure and sliding distance are the two dominant factors in determining sliding wear. We applied the finite element analysis to accurately quantify the contact pressure and sliding distance at the die radius in sheet metal stamping. The results were then applied to analyze sliding wear at the die radius. We found that a typical two-peak steady-state contact pressure response exists during a channel forming process. The steady-state contact pressure response was preceded by an initial transient response, which produced extremely large and localized contact pressures. We proposed a method to numerically quantify the sliding distance, which was applied to examine the contact sliding distance at the die radius. Correlating the contact pressure and sliding distance, a new insight into the wear/galling that occurs at the die radius in sheet metal stamping was gained. The results show that the region close to zero degrees on the die radius is likely to experience the most wear, with the identified transient stage contributing to a large proportion of the total wear.

Temperature conditions during 'cold' sheet metal stamping

This paper investigates the friction and deformation-induced heating that occurs during the stamping of high strength sheet steels, under room temperature conditions. A thermo-mechanical finite element model of a typical plane strain stamping process was developed to understand the temperature conditions experienced within the die and blank material; and this was validated against experimental measurements. A high level of correlation was achieved between the finite element model and experimental data for a range of operating conditions and parameters. The model showed that the heat generated during realistic production conditions can result in high temperatures of up to 108 °C and 181 °C in the blank and die materials, respectively, for what was traditionally expected to be 'cold' forming conditions. It was identified that frictional heating was primarily responsible for the peak temperatures at the die surface, whilst the peak blank temperatures were caused by a combination of frictional and deformation induced heating. The results provide new insights into the local conditions within the blank and die, and are of direct relevance to sheet formability and tool wear performance during industrial stamping processes. © 2014 Elsevier B.V. All rights reserved.

An audio signal based model for condition monitoring of sheet metal stamping process

Tool condition monitoring is an important factor in ensuring manufacturing efficiency and product quality. Audio signal based methods are a promising technique for condition monitoring. However, the influence of interfering signals and background noise has hindered the use of this technique in production sites. Blind signal separation (BSS) has the potential to solve this problem by recovering the signal of interest out of the observed mixtures, given that the knowledge about the BSS model is available. In this paper, we discuss the development of the BSS model for sheet metal stamping with a mechanical press system, so that the BSS techniques based on this model can be developed in future. This involves conducting a set of specially designed machine operations and developing a novel signal extraction technique. Also, the link between stamping process conditions and the extracted audio signal associated with stamping was successfully demonstrated by conducting a series of trials with different lubrication conditions and levels of tool wear.

Path independent limiting criteria in sheet metal forming

The Forming Limit Diagram (FLD) is a conventional failure diagram to estimate necking limits of sheet metal for proportional loading conditions. Previous studies reveal that the FLD is not suitable for predicting the influence of nonlinear strain paths. This paper presents methodical comparison among all common available strain path independent strain/stress based limiting criteria. All the strain path independent strain based limiting criteria (Traditional Failure Diagram (TFD), Extended Forming Limit Diagram (XFLD), Extended Stress Ratio Based Forming Limit Diagram (ESRFLD), and Polar Effective Plastic StrainDiagram (PEPSD)) and stress based limiting criteria (Traditional Stress based Failure Diagram (TFSD), Stress Based Forming Limit Diagram (FLSD), Stress Ratio and Stress Based Forming Limit Diagram (SRFLSD), Extended Stress Based Forming Limit Diagram (XFLSD), and Polar Effective Stress Diagram (PESSD)) are approximately path-independent for smaller amount of pre-straining and path dependent for large pre-straining conditions. From advance image correlation technique precisely determination of local strains near necked area is possible today. However direct determination of local stresses near necked area is not possible. Therefore, local stresses and equivalent stress are determined by employing both yield criterion and strain-hardening law. Similarly equivalent strain is calculated by the use of yield criterion. Therefore, the choice of yield criterion has an impact on the results for TFD, XFLD, ESRFLD and PEPSD. However, selections of both yield criterion and strain-hardening law have substantial influence on the results for TFSD, FLSD, SRFLSD, XFLSD and PESSD. The inherent calculation error can be minimized by generation of experimental data for each material and then selection of representable yield criterion and strain-hardening law. Improvement of experimental techniques and generation of rigorous material data bank in various strain paths may help researchers to diagnose and resolve the issue. TFD, TFSD and XFLSD have inherent variables to take care the effect of through thickness stress, however rigorous experimental verification is needed before the field application.