Ionic conductivity studies of polymeric electrolytes containing lithium salt with plasticizer

New plasticized polymer electrolytes were synthesized based on poly ethylene oxide (PEO), Poly (N,N-dimethylamino-ethyl-methacrylate) (PDMAEMA), LiN(CF₃SO₂)₂ (LITFSI) as the salt and tetraethylene glycol dimethyl ether(tetraglyme) and EC + PC as plasticizers. The preparation and characterization of the polymer electrolytes were investigated as a function of temperature and various concentrations of LITFSI. Impedance spectroscopy and differential scanning calorimeter (DSC) were used to characterize the effects of various temperature, lithium salt concentration and two plasticizers on conductivity. The complex of PDMAEMA/PEO/LiTFSI/tetraglyme (S2) exhibits higher conductivity (4.74 × 10⁻⁴ S cm⁻¹at 25 °C) than PDMAEMA/PEO/LiTFSI/EC + PC (S1).

Ion diffusion in molten salt mixtures

The molten salts, 1-methyl,3-ethylimidazolium trifluoromethanesulfonate (triflate salt, MeEtImTf) and 1-methyl,3-ethylimidazolium bis(trifluoromethanesulfonimide) (imide salt, MeEtImNTf₂) are colourless ionic liquids with conductivities of the order of 10⁻² S cm⁻¹ at room temperature. DSC measurements revealed subambient melting and glass transition temperatures. Analysis of the anion and cation diffusion coefficients suggested that the cation was the dominant charge carrier and that the motion was largely independent of the anion. Haven ratios (H_Rs) of 1 and 1.6 were determined for the imide and triflate salts, respectively, at 30°C (303 K). Values greater than one imply some degree of ionic association, suggesting that aggregation is present in the triflate salt. Mixing of the salts to form binary systems resulted in enhanced conductivities which deviated from a simple law of mixtures. Thermal analysis showed no evidence of a melting point with only a glass transition observed. Corresponding diffusion measurements for the binaries appeared to show a weighted average of the diffusion coefficients of the pure components. The increased conductivity can be attributed to an increase in the number of charge carriers as a result of decreased ion association in the binary.

NMR and Raman studies of a novel fast-ion-conducting polymer-in-salt electrolyte based on LiCF3SO3 and PAN

We report spectroscopic results from investigations of a novel solid polymeric fast-ion-conductor based on poly(acrylonitrile), (PAN, of repeat unit [CH₂CH(CN)]_n), and the salt LiCF₃SO3 . From NMR studies of the temperature and concentration dependencies of ⁷Li- and ^lH-NMR linewidths, we conclude that significant ionic motion occurs at temperatures close to the glass transition temperature of these polymer-in-salt electrolytes, in accordance with a recent report on the ionic conductivity. In the dilute salt-in-polymer regime, however, ionic motion appears mainly to be confined to local salt-rich domains, as determined from the dramatic composition dependence of the ionic conductivity. FT-Raman spectroscopy is used to directly probe the local chemical anionic environment, as well as the Li⁺–PAN interaction. The characteristic δ_s(CF₃) mode of the CF₃SO₃⁻ anion at _~750–780 cm^−l shows that the ionic substructure is highly complex. Notably, no spectroscopic evidence of free anions is found even at relatively salt-depleted compositions (e.g. N:Li_~60–10:1). A strong Li⁺–PAN interaction is manifested as a pronounced shift of the characteristic polymer C=N stretching mode, found at _~2244 cm^−l in pure PAN, to _~2275 cm^−l for Li⁺-coordinated C=N moieties. Our proton-NMR data suggest that upon complexation of PAN with LiCF3 SO₃, the glass transition occurs at progressively lower temperatures.

Novel high salt content polymer electrolytes based on high Tg polymers

Conductivities greater than or equal to 10⁻⁸ S cm⁻¹ at T_g are reported in polymer electrolytes based on lithium triflate salt and a series of polymers whose T_g is greater than 90°C. The highest conductivities were observed for poly(acrylonitrile) based systems with salt concentrations greater than 60 wt.%. The conductivity in all cases investigated increases with increasing salt concentration. ¹H-NMR T₂ relaxation measurements suggest that T_g decreases with increasing salt content and confirms that these materials are glassy at room temperature and hence that the conductivity is significantly decoupled from the structural relaxations. It appears that the nature of the polymer is important in determining the level of ionic conductivity, possibly due to differences in polymer coordinating ability or differences in T_g. Polymer-in-salt mixtures based on a tetra-alkyl ammonium imide molten salt and several high T_g polymers are also reported. The conductivities of these mixtures appear to be independent of the polymer type.

Glass transition and free volume behaviour of poly(acrylonitrile)/LiCF3SO3 polymer-in-salt electrolytes compared to poly(ether urethane)/LiClO4 solid polymer electrolytes

Measurements of the glass transition temperature (T_g) and free volume behaviour of poly(acrylonitrile) (PAN) and PAN/lithium triflate (LiTf), with varying salt composition from 10 to 66 wt% LiTf, were made by positron annihilation lifetime spectroscopy (PALS). Addition of salt from 10 to 45 wt% LiTf resulted in an increase in the mean free volume cavity size at room temperature (r.t.) as measured by the orthoPositronium (oPs) pickoff lifetime, τ₃, with little change in relative concentration of free volume sites as measured by oPs pickoff intensity, I₃. The region from 45 to 66 wt% salt displayed no variation in relative free volume cavity size and concentration. This salt concentration range (45 wt%<[LiTf]<66 wt%) corresponds to a region of high ionic conductivity of order 10⁻⁵ to 10⁻⁶ S cm⁻¹ at T_g as measured by PALS. A percolation phenomenon is postulated to describe conduction in this composition region. Salt addition was shown to lower the T_g as measured by PALS; T_g was 115°C for PAN and 85°C for PAN/66 wt% LiTf. The T_g and free volume behaviour of this polymer-in-salt electrolyte (PISE) was compared to a poly(ether urethane)/LiClO₄ where the polymer is the major component, i.e. traditional solid polymer electrolyte (SPE). In contrast to the PISE, the T_g of the SPE was shown to increase with increasing salt concentration from 5.3 to 15.9 wt%. The relative free volume cavity size and concentration at r.t. were shown to decrease with increasing salt concentration. Ionic conductivity in this SPE was of order 10⁻⁵ S cm⁻¹ at r.t., which is over 60°C above T_g, 10⁻⁸ S cm⁻¹ at 25°C above T_g, and conductivity was not measurable at T_g.

Molecular dynamics simulations of highly concentrated salt solutions : structural and transport effects in polymer electrolytes

Structural, thermodynamic and transport properties have been calculated in concentrated non-aqueous NaI solutions using molecular dynamics simulations. Although the solvent has been represented by a simplistic Stockmayer fluid (spherical particles with point dipoles), the general trends observed are still a useful indication of the behavior of real non-aqueous electrolyte systems. Results indicate that in low dielectric media, significant ion pairing and clustering occurs. Contact ion pairs become more prominent at higher temperatures, independent of the dielectric strength of the solvent. Thermodynamic analysis shows that this temperature behavior is predominantly entropically driven. Calculation of ionic diffusivities and conductivities in the NaI/ether system confirms the clustered nature of the salt, with the conductivities significantly lower than those predicted from the Nernst-Einstein relation. In systems where the solvent-ion interactions increase relative to ion-ion interactions (lower charge or higher solvent dipole moment), less clustering is observed and the transport properties indicate independent motion of the ions, with higher calculated conductivities. The solvent in this system is the most mobile species, in comparison with the polymer electrolytes where the solvent is practically immobile.

Solid state lithium ion conduction in pyrrolidinium imide–lithium imide salt mixtures

The properties of the binary salt system based on mixtures of methyl ethyl pyrrolidinium bis(trifluoromethane sulfonyl) imide (P₁₂) and lithium bis(trifluoromethane sulfonyl) imide (Li imide) are reported. The lithium containing mixtures were found to be more than two orders of magnitude more conductive than the parent P₁₂ phase and the 33 mol% Li imide systems showed a solid state conductivity around 1×10⁻⁴ S/cm at 20°C. This solid state conductivity is believed to take place in plastic crystal phases of the P₁₂ compound.

Ion conductivity in amorphous polymer/salt mixtures

Amorphous polymer/salt mixtures based on polyvinyl alcohol and poly(hydroxyethylacrylate) and poly(hydroxyethylmethacrylate) are described. The polyvinylalcohol materials have been prepared by a solvent free hot pressing technique as well as the traditional solvent casting method. The hot pressing technique allows the production of samples which are genuinely free of solvents and thereby has allowed an assessment in this work of the effect of residual solvent on conductivity. The acrylate materials were prepared by direct polymerization of monomer/salt mixtures, thus avoiding the need for solvents. These materials have glass transitions around or well above room temperature, but nonetheless have conductivities as high as 10⁻⁷ S/cm at room temperature. The temperature and composition dependence of conductivity are also presented.

Highly concentrated salt solutions : molecular dynamics simulations of structure and transport

Molecular dynamics (MD) simulations in NaI solutions, where the solvent has been represented by the Stockmayer fluid, were performed as a function of temperature, salt concentration, and solvent dipole strength. At higher temperatures contact ion pairs become more prevalent, regardless of solvent strength. An examination of the temperature dependence of the potential of mean force demonstrates the entropic nature of this effect. The transport properties calculated in the simulations are dependent on the balance between solvent dielectric constant and ion charge. In systems with a large solvent dipole moment, the ions appear to be independently mobile, and deviations from Nernst–Einstein behavior are small. In systems of smaller solvent dipole moment or greater ion charge, the ions form clusters, and large deviations from Nernst–Einstein behavior are observed.

Poly methacrylate-plasticiser-salt blends as solid polymer electrolytes

Methoxy-ethylene glycol methacrylates, CH₂=CMeCOO(CH₂CH₂O)_nMe (n = 1, 2, 3), ethoxy-triethylene glycol methacrylate, CH₂=CMeCOO(CH₂CH₂O)₃Et, and N,N-dimethylaminoethyl methacrylate, CH₂=CMeCOOCH₂CH₂NMe₂, were used to synthesise the corresponding polymers. Conductivities of these polymers complexed with lithium perchlorate were investigated. Tetraethylene glycol dimethyl ether was used as plasticiser to increase the conductivity of the materials. A conductivity of 10⁻⁵ S cm⁻¹ was obtained at room temperature for the plasticised polymer samples. Effects of polymer structure, plasticiser, salt concentration and temperature on conductivity and glass transition temperature of the polymer electrolytes are discussed.

Mechanical properties of polyether-plasticiser-salt systems as polymer electrolytes

The mechanical properties of urethane crosslinked poly(ethylene oxide-co-propylene oxide) glyceryl ether-plasticiser (tetraethylene glycol dimethyl ether, or methylformamide)-salt (LiClO₄)-based polymer electrolytes have been studied. It was found that, with increasing concentration of salt, the elastic modulus and tensile strength of the materials unexpectedly decrease. This is interpreted in terms of a predominance of intramolecular coordination of the Li⁺ ions by the polymer.

Gel electrolytes based on lithium macro-anion salt

Montmorillonites are composed of aluminosilicate layers stacked one above the other, and the layer thickness is approximately 1 nm. In this work lithium modified montmorillonite (Li-MMT) was prepared and used as a lithium macro-anion salt in gel electrolytes. It was found that Li-MMT exhibited good compatibility with poly(ethylene glycol), DMSO and the ionic liquid, 1-ethyl-3-methylimidazolium dicyanamide (EMIdca), and a few of novel gel electrolytes based on Li-MMT were obtained. These gel electrolytes were investigated by X-ray powder diffraction, solid state NMR, conductivity measurements and cyclic voltammetry. High conductivities up to 10^{− 4} to 10^{− 3} S/cm at room temperature were observed with these macro-anion gel electrolytes. These gel materials were promising to be used as lithium conductive electrolytes in electrochemical devices, such as lithium batteries.