Using titania photocatalysts to degrade toluene in a combined adsorption and photocatalysis process

Three types of titania supported materials including titanium dioxide and silicon dioxide composite, titania-coated activated carbon and titania-coated glass beads were prepared and used as photocatalysts to remove toluene from an air stream. Their surface areas were analysed. TEM image reveals titania-silica composites were nanostructured aggregates. XRD was used to determine their crystalline phase which was 100% anatase for the titania component. A fixed bed reactor was designed and built in the laboratory, the toluene with initial concentration of 300 ppm (1149 mg/m³) was fed into the reactor, the destruction efficiencies of toluene were determined by the gas analyser. It was also found that TiO₂-SiO₂ aggregates with high surface area (421.1 m²/g) achieved high destruction efficiencies. The combined effects of adsorption and photocatalysis were further studied by comparing the performance of pure activated carbon (surface area of 932.4 m²/g) and TiO₂ coated activated carbon with BET surface area of 848.4 m²/g. It was found that the TiO₂ coated activated carbon demonstrated comparable results to pure activated carbon, and most importantly, the TiO₂-coated activated carbon can be effectively regenerated by UV irradiation, and was reused as adsorbent. The experimental result of titania-coated glass beads demonstrated a steady degradation efficiency of 15% after a period of 17 hours. It helped to understand that photocatalysis degradation ability of the TiO₂ was constant regardless of the adsorption capacity of the catalysts. This photocatalytic property can be used to degrade the adsorbed toluene and regenerate the catalyst. This study revealed that if the experiments were designed to use adsorption to remove toluene and followed by regeneration of adsorbent using photocatalysis, it could achieve a very high removal efficiency of toluene and reduce the regeneration cost of saturated adsorbent.

Effect of weight reduction pre-treatment on the electrical and thermal properties of polypyrrole coated woven polyester fabrics

Weight reduction increased the amount of deposited polypyrrole (PPy) on the polyester (PET) fiber surface, leading to a considerable decrease in electrical resistance and improved heat generation capacity for the PPy coated PET fabrics. Application of dc voltages to an insulated roll of PPy-coated fabric increased the temperature to about 90 °C. This showed the suitability of these fabrics for heating applications. The optimum PPy deposition of about 2.8% was obtained in samples weight reduced by aqueous sodium hydroxide treatment. AFM images revealed a smooth surface morphology of the untreated fiber whereas the treated fiber had a high surface roughness.

Conducting polymer coated fabrics for potential applications in microwave frequencies : a study of electromagnetic properties

The microwave reflection, transmission and complex permittivity of paratoluene-2-sulfonic acid doped conducting polypyrrole (PPy/pTSA) coated Nylon-Lycra textiles in the 1-18 GHz frequency were investigated. The real part of permittivity increased with polymerization time and dopant concentration, reaching a plateau at certain dopant concentration and polymerization time. The imaginary part of permittivity showed a frequency dependent change throughout the tested range. All the samples had higher values of absorption than reflection. The total electromagnetic shielding effectiveness exceeded 80% for the highly pTSA doped samples coated for 3 hours.

Effects of laundering on conductivity of polypyrrole-coated textiles

This study examines the resistance change in conductive polypyrrole-coated PET fabrics under the AS 2001.4.15 – 1994 laundering test conditions. The effects of individual detergent components of a standard detergent, including auxiliary chemicals, at four different temperatures were studied. When the coated fabric was washed under the AS 2001.4.15-1994 conditions, the ECE reference detergent and pure soap flakes (sodium sterate) both decreased the conductivity of the coating at a rate exponentially proportional to the laundering temperature. Detergent types had an influence over the rate of degradation; pH conditions had a large influence on the rate of polymer deterioration with the acidic nonionic detergent giving rise to significantly improved laundering conditions. The auxiliary chemicals, sodium carbonate and sodium perborate were seen to cause large degradation of polymers during laundering. Ethylene diamine tetra acetic acid was seen to have only a slight influence on the reduction of conductivity of polymers.

Characterization of conducting polymer coated fabrics at microwave frequencies

Purpose – The purpose of this paper is to investigate microwave reflection, transmission, and complex permittivity of p-toluene-2-sulfonic acid doped conducting polypyrrole coated nylon-lycra textiles in the 1-18?GHz frequency with a view to potential applications in the interaction of electromagnetic radiation with such coated fabrics.

Design/methodology/approach – The chemical polymerization of pyrrole is achieved by an oxidant, ferric chloride and doped with p-toluene sulfonic acid (pTSA) to enhance the conductivity and improve stability. Permittivity of the conducting textile substrates is performed using a free space transmission method accompanied by a mathematical diffraction reduction method.

Findings – The real part of permittivity increases with polymerization time and dopant concentration, reaching a plateau at certain dopant concentration and polymerization time. The imaginary part of permittivity shows a frequency dependent change throughout the test range. All the samples have higher values of absorption than reflection. The total electromagnetic shielding effectiveness exceeds 80 percent for the highly pTSA doped samples coated for 3?h.

Originality/value – A non-contact, non-destructive free space method thin flexible specimens to be tested with high accuracy across large frequency range. The non-destructive nature of the experiments enables investigation of the stability of the microwave transmission, reflection, absorption and complex permittivity values. Moreover, mathematical removal of the diffraction enables higher accuracy.

Short-term heating tests on doped polypyrrole-coated polyester fabrics

Polyethyleneterephtalate–polypyrrole (PET–PPy) textile complexes incorporating different anionic dopants have been heat treated at 60 °C, 80 °C, 105 °C, 125 °C and 150 °C to investigate effects of short-term heating on conductivity and stability. In most cases heat treatments below 80 °C did not significantly change the final resistance of the conducting textiles. Only the anionic dye-dopant Indigo Carmine acted in a heat-stabilizing manner during treatment at 150 °C, while all samples containing other anionic dopant underwent some degradation. A treatment temperature of 125 °C was the most effective for lowering the final resistance, with sulphonic group containing dopants being particularly effective in improving conductivity and stability. A 29% decrease in the final resistance of a PET–PPy/para-toluene-2-sulphonic acid (pTSA) sample was achievable after 900 s at 125 °C.

The influence of polymerization time and dopant concentration on the absorption of microwave radiation in conducting polypyrrole coated textiles

Temperature changes in conducting polypyrrole/para-toluene-2-sulphonic acid (PPy/pTSA) coated nylon textiles due to microwave absorption in the 8–9 GHz and 15–16 GHz frequency ranges were obtained by a thermography station during simultaneous irradiation of the samples. The temperature values are compared and related to the amounts of reflection, transmission and absorption obtained with a non-contact free space transmission technique, indicating a relationship between microwave absorption and temperature increase. Non-conductive samples showed no temperature increase upon irradiation irrespective of frequency range. The maximum temperature difference of around 4 °C in the conducting fabrics relative to ambient temperature was observed in samples having 48% absorption and 26.5 ± 4% reflection. Samples polymerized for 60 or 120 min with a dopant concentration of 0.018 mol/l or polymerized for 180 min with a dopant concentration of 0.009 mol/l yielded optimum absorption levels. As the surface resistivity decreased and the reflection levels increased, the temperature increase upon irradiation reduced.

One-step coating of fluoro-containing silica nanoparticles for universal generation of surface superhydrophobicity

Stable superhydrophobic surfaces with water contact angles over 170 degrees and sliding angles below 7 degrees were produced by simply coating a particulate silica sol solution of co-hydrolysed TEOS/fluorinated alkyl silane with NH₃^.H₂O on various substrates, including textile fabrics (e.g. polyester, wool and cotton), electrospun nanofibre mats, filter papers, glass slides, and silicon wafers.

Fast response photochromic textiles from hybrid silica surface coating

In this study, a hybrid silica sol-gel embedded with a photochromic dye has been applied to wool fabric to form a photochromic coating. The treated wool fabrics showed very quick photochromic response. Five different silanes have been used as the silica precursor, and the resultant coating showed slight differences in photochromic performance, fabric washing fastness, and surface hydrophilicity. However, the silica type had a considerable influence on fabric handle property. The silica matrix from the silane containing a long alkyl chain had a very little influence on the fabric handle and better photochromic performance than those from other different silane precursors.

Natural rubber nanocomposite reinforced with nano silica

Inorganic nano fillers have demonstrated great potential to enhance the properties of natural rubber (NR). The present article reports the successful development of a NR nanocomposite reinforced with nano silica (SiO2). Its dynamic mechanical properties, thermal aging resistance, and morphology are investigated. The results show that the SiO2 nanoparticles are homogenously distributed throughout the NR matrix in a form of spherical nano-cluster with an average size of 80 nm when the SiO2 content is 4 wt%. With the introduction of SiO2, the thermal resistance and the storage modulus of NR host significantly increase, and the activation energy of relaxation of the nanocomposite, compared to the raw NR, increases from 90.1 to 125.8 kJ/mol.

Reverse microemulsion-mediated synthesis of SiO2-coated ZnO composite nanoparticles : multiple cores with tunable shell thickness

Monodispersed SiO₂-shell/ZnO-core composite nanospheres have been prepared in an oil-in-water microemulsion system. By using cyclohexane as the oil phase and Triton X-100 as the surfactant, composite nanospheres with high core loading levels and tunable shell thickness were obtained. Utilization of PVP capping agent on ZnO allowed the synthesis of composite nanospheres without forming any coreless SiO2 spheres or shell-less ZnO particles. The photoactivity of ZnO nanoparticles was greatly reduced by SiO2-coating, which enables their applications as durable, safe, and nonreactive UV blockers in plastics, coating, and other products.