Estimating hydrogen sulphide dissipation rate constant under the influence of different chemical dosing

Sewer odour and corrosion is caused by the reduction of sulphide ions and the release of hydrogen sulphide gas (H2S) into the sewer atmosphere. The reduction of sulphide is determined by its dissipation rate which depends on many processes such as emission, oxidation and precipitation that prevail in wastewater environments. Two factors that mainly affect the dissipation of sulphide are sewer hydraulics and wastewater characteristics; modification to the latter by dosing certain chemicals is known as one of the mitigation strategies to control the dissipation of sulphide. This study investigates the dissipation of sulphide in the presence of NaOH, Mg(OH)2, Ca(NO3)2 and FeCl3 and the dissipation rate is developed as a function of hydraulic parameters such as the slope of the sewer and the velocity gradient. Experiments were conducted in a 18m experimental sewer pipe with adjustable slope to which, firstly no chemical was added and secondly each of the above mentioned chemicals was supplemented in turn. A dissipation rate constant of 2×10^-6 for sulphide was obtained from experiments with no chemical addition. This value was then used to predict the sulphide concentration that was responsible for the emission of H2S gas in the presence of one of the above mentioned four chemicals. It was found that the performance of alkali substances (NaOH and Mg(OH)2) in suppressing the H2S gas emission was excellent while ferric chloride showed a moderate mitigating effect due to its slow reaction kinetics. Calcium nitrate was of little value since the wastewater used in this study experienced almost no biological growth. Thus the effectiveness of selected chemicals in suppressing H2S gas emission had the following order: NaOH ≥ Mg(OH)2 ≥ FeCl3 ≥ Ca(NO3)2.

Yielding behaviour of martensite in steel

Although martensite is recognised as a very strong phase in carbon steels, its initial yielding commences at low stresses and the tensile stress-strain curve shows a smooth, rounded form. Evidence is presented from x-ray diffraction to show that this behaviour is due to the presence of intra-granular stresses that are residues after the shear transformation from austenite to martensite. These internal stresses are reduced in magnitude by plastic deformation and also by tempering. Reduction of internal stress due to plasticity is shown by a decrease in XRD line broadening after deformation. A simple model is presented in which the stress-strain behaviour is controlled by relaxation of the internal stresses almost up to the point of the ultimate tensile strength. It demonstrates that only a very small fraction of the material remaining in a purely elastic state provides a large stabilising effect resisting necking. A corollary of this is that the uniform elongation of martensitic steel actually increases with increase in the strength level. Effects of heat treatment are also reproduced in the model, including the increase in conventional yield stress (Rp0.2) that occurs after low temperature tempering.

Characterisation of ion transport in sulfonate based ionomer systems containing lithium and quaternary ammonium cations

Two sulfonated ionomers based on poly(triethylmethyl ammonium 2-acrylamido-2-methyl-1-propane sulfonic acid) (PAMPS) and containing mixtures of Li⁺ and quaternary ammonium cations are characterised. The first system contains Li⁺ and the methyltriethyl ammonium cation (N1222) in a 1:9 molar ratio, and the ⁷Li NMR line widths showed that the Li⁺ ions are mobile in this system below the glass transition temperature (105°C) and are therefore decoupled from the polymer segmental motion. The conductivity in this system was measured as 10^-5 Scm^-1 at 130°C. A second PAMPS system containing Li⁺ and the dimethylbutylmethoxyethyl ammonium cation (N114(2O1)) in a 2:8 molar ratio showed much lower conductivities despite a significantly lower Tg (60°C), possibly due to associations between the Li⁺ and the ether group on the ammonium cation, or between the latter cations and the sulfonate groups.

Electrochemistry of tris(2,2′-bipyridyl) cobalt(II) in ionic liquids and aprotic molecular solvents on glassy carbon and platinum electrodes

The tris(2,2′-bipyridyl) complexes of cobalt(II) and (III) ([Co(bpy)3]^2+/3+) produce a redox couple of great interest in thermoelectrochemical cells and dye sensitized solar cells including both types of devices based on ionic liquid electrolytes. We present a systematic study of the electrochemistry of [Co(bpy)3]²⁺ [NTf2]^-2 in two ionic liquids (ILs) based on the 1-ethyl-3-methylimidazolium (C2mim) cation and two ILs based on the 1-butyl-1-methylpyrrolidinium cation (C4mpyr), as well as three aprotic molecular solvents. Platinum (Pt) and glassy carbon (GC) working electrodes were compared. In all solvents better electrochemical responses were observed on GC, which yielded higher currents in the cyclic voltammograms and lower rate constants for the redox reaction. The [Co(bpy)3]^1+/2+ couple is also readily observed, but this redox reaction is chemically irreversible, possibly because the [Co(bpy)3]¹⁺ complex dissociates. However, the [Co(bpy)3]^1+/2+ reaction is chemically reversible in all of the solvents studied, except 3-methoxypropionitrile, if excess of 2,2′-bipyridyl is added to the solution.

What doesn’t kill you makes you fitter: A systematic review of high-intensity interval exercise for patients with cardiovascular and metabolic diseases

High-intensity interval exercise (HIIE) has gained popularity in recent years for patients with cardiovascular and metabolic diseases. Despite potential benefits, concerns remain about the safety of the acute response (during and/or within 24 hours postexercise) to a single session of HIIE for these cohorts. Therefore, the aim of this study was to perform a systematic review to evaluate the safety of acute HIIE for people with cardiometabolic diseases. Electronic databases were searched for studies published prior to January 2015, which reported the acute responses of patients with cardiometabolic diseases to HIIE (≥80% peak power output or ≥85% peak aerobic power, VO2peak). Eleven studies met the inclusion criteria (n = 156; clinically stable, aged 27-66 years), with 13 adverse responses reported (∼8% of individuals). The rate of adverse responses is somewhat higher compared to the previously reported risk during moderate-intensity exercise. Caution must be taken when prescribing HIIE to patients with cardiometabolic disease. Patients who wish to perform HIIE should be clinically stable, have had recent exposure to at least regular moderate-intensity exercise, and have appropriate supervision and monitoring during and after the exercise session.

Gelled ionic liquid sodium ion conductors for sodium batteries

Owing to the unique properties of certain Ionic liquids (ILs) as safe and green solvents, as well as the potential of sodium as an alternative to lithium as charge carriers, we investigate gel sodium electrolytes as safe, low cost and high performance materials with sufficient mechanical properties for application in sodium battery technologies. We investigate the effect of formation of two types of gel electrolytes on the properties of IL electrolytes known to support Na/Na⁺ electrochemistry. The ionic conductivity is only slightly decreased by 0.0005 and 0.0002 S cm^-1 in the case of 0.3 and 0.5 M NaNTf2 systems respectively as the physical properties transition from liquid to gel. We observed facile plating and stripping of Na metal around 0 V vs. Na/Na⁺ through the cyclic voltammetry. A wide-temperature range of the gelled IL state, of more than 100 K around room temperature, is achieved in the case of 0.3 and 0.5 M NaNTf2. We conclude that the formation of a gel does not significantly affect the liquid-like ion dynamics in these materials, as further evidenced by DSC and FTIR analysis.

Bioinspired strategy for tuning thermal stability of PVA via hydrogen-bond crosslink

Although many approaches have been employed to enhance thermal stability of PVA, developing a facile and effective strategy remains highly attractive. Herein, we demonstrate a highly effective approach to strikingly improve thermal stability of PVA by selecting the types of multiamines molecules to tune the hydrogen-bond crosslink density. Results show that only adding 0.5 wt% of 2,4,5,6-tetraaminopyrimidine can make the initial degradation temperature (Ti) and maximum degradation temperature (Tmax) of PVA increase by ~55 °C and 98 °C due to the formation of 3D physically H-bond crosslinked network, resulting in superior thermal stability property to those of PVA nanocomposites. Moreover, thermal stability strongly depends on the H-bond crosslink density, and Ti and Tmax basically obey the linear hydrogen-bond relations despite some deviations. This work opens up a novel biological methodology for creating thermally stable polymeric materials.

LNA aptamer based multi-modal, Fe3O4-saturated lactoferrin (Fe3O4-bLf) nanocarriers for triple positive (EpCAM, CD133, CD44) colon tumor targeting and NIR, MRI and CT imaging

This is the first ever attempt to combine anti-cancer therapeutic effects of emerging anticancer biodrug bovine lactoferrin (bLf), and multimodal imaging efficacy of Fe3O4 nanoparticles (NPs) together, as a saturated Fe3O4-bLf. For cancer stem cell specific uptake of nanocapsules/nanocarriers (NCs), Fe3O4-bLf was encapsulated in alginate enclosed chitosan coated calcium phosphate (AEC-CP) NCs targeted (Tar) with locked nucleic acid (LNA) modified aptamers against epithelial cell adhesion molecule (EpCAM) and nucleolin markers. The nanoformulation was fed orally to mice injected with triple positive (EpCAM, CD133, CD44) sorted colon cancer stem cells in the xenograft cancer stem cell mice model. The complete regression of tumor was observed in 70% of mice fed on non-targeted (NT) NCs, with 30% mice showing tumor recurrence after 30 days, while only 10% mice fed with Tar NCs showed tumor recurrence indicating a significantly higher survival rate. From tumor tissue analyses of 35 apoptotic markers, 55 angiogenesis markers, 40 cytokines, 15 stem cell markers and gene expression studies of important signaling molecules, it was revealed that the anti-cancer mechanism of Fe3O4-bLf was intervened through TRAIL, Fas, Fas-associated protein with death domain (FADD) mediated phosphorylation of p53, to induce activation of second mitochondria-derived activator of caspases (SMAC)/DIABLO (inhibiting survivin) and mitochondrial depolarization leading to release of cytochrome C. Induction of apoptosis was observed by inhibition of the Akt pathway and activation of cytokines released from monocytes/macrophages and dendritic cells (interleukin (IL) 27, keratinocyte chemoattractant (KC)). On the other hand, the recurrence of tumor in AEC-CP-Fe3O4-bLf NCs fed mice mainly occurred due to activation of alternative pathways such as mitogen-activated protein kinases (MAPK)/extracellular signal-regulated kinases (ERK) and Wnt signaling leading to an increase in expression of survivin, survivin splice variant (survivin 2B) and other anti-apoptotic proteins Bad, Bcl-2 and XIAP. Apart from the promising anti-cancer efficacy and the exceptional tumor targeting ability observed by multimodal imaging using near-infrared (NIR) imaging, magnetic resonance imaging (MRI) and computerized tomographic (CT) techniques, these NCs also maintained the immunomodulatory benefits of bLf as they were able to increase the RBC, hemoglobin, iron calcium and zinc levels in mice.

A highly conductive porous graphene electrode prepared via in situ reduction of graphene oxide using Cu nanoparticles for the fabrication of high performance supercapacitors

Herein, a new graphene/Cu nanoparticle composite was prepared via the in situ reduction of GO in the presence of Cu nanoparticles which was then utilized as a sacrificing template for the formation of flexible and porous graphene capacitor electrodes by the dissolution of the intercalated Cu nanoparticle in a mixed solution of FeCl3 and HCl. The porous RGO electrode was characterized by atomic force microscopy (AFM), Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) and thermogravimetric analysis (TGA). The as-prepared graphene/Cu nanoparticle composite and the pure graphene film after removal of Cu nanoparticles possessed high conductivity of 3.1 × 10³ S m^-1 and 436 S m^-1 respectively. The porous RGO can be used as the electrode for the fabrication of supercapacitors with high gravimetric specific capacitances up to 146 F g^-1, good rate capability and satisfactory electrochemical stability. This environmentally friendly and efficient approach to fabricating porous graphene nanostructures could have enormous potential applications in the field of energy storage and nanotechnology.

Supramolecular ionic networks with superior thermal and transport properties based on novel delocalized di-anionic compounds

Supramolecular ionic networks based on highly delocalized dianions having (trifluoromethane-sulfonyl)imide, (propylsulfonyl)methanide and (cyano-propylsulfonyl)imide groups were developed and their physical properties were examined in detail. Most of the synthesized compounds were semi-crystalline possessing Tm values close to 100°C; however, amorphous networks were also obtained using aromatic asymmetric dianions. Rheological measurements in temperature sweep tests at a constant frequency confirmed two different behaviors: a fast melting close to the Tm for semi-crystalline materials and a thermoreversible network for liquid transition for the amorphous supramolecular ionic networks. It was found that the amorphous ionic networks showed significantly higher ionic conductivity (10^-3 S cm^-1 at 100°C) than the crystalline ionic networks (10^-6 S cm^-1) and previously reported amorphous citrate ionic networks (10^-5 S cm^-1). The supramolecular ionic networks containing hydrophobic (trifluoromethanesulfonyl)imide groups demonstrated improved water stability and higher thermal stability than the previously synthesized carboxylate ones. Noticeably, the obtained amorphous supramolecular ionic networks combine not only high ionic conductivity and thermal stability, but also self-healing properties into the same material.

Mobile phone-based electrochemiluminescence sensing exploiting the 'USB On-The-Go' protocol

A low-cost system to generate, control and detect electrochemiluminescence using a mobile smartphone is described. A simple tone-detection integrated circuit is used to switch power sourced from the phone's Universal Serial Bus (USB) 'On-The-Go' (OTG) port, using audible tone pulses played over the device's audio jack. We have successfully applied this approach to smartphones from different manufacturers and with different operating system versions. ECL calibrations of a common luminophore, tris(2,2′-bipyridine)ruthenium(II) ([Ru(bpy)3]²⁺), with 2-(dibutylamino)ethanol (DBAE) as a co-reactant, showed no significant difference in light intensities when an electrochemical cell was controlled by a mobile phone in this manner, compared to the same calibration generated using a conventional potentiostat. Combining this novel approach to control the applied potential with the measurement of the emitted light through the smart phone camera (using an in-house built Android app), we explored the ECL properties of a water-soluble iridium(III) complex that emits in the blue region of the spectrum. The iridium(III) complex exhibited superior co-reactant ECL intensities and limits of detection to that of the conventional [Ru(bpy)3]²⁺ luminophore.

Dietary micronutrients and in vivo n-3 LC-PUFA biosynthesis in Atlantic salmon

Aquaculture, and in particular Atlantic salmon culture, is expected to deliver n. -3 long-chain polyunsaturated fatty acid (n. -3 LC-PUFA) rich products. Nevertheless, the availability of n. -3 LC-PUFA rich raw materials for aquafeed is dwindling, and at an ever increasing market price. Thus, there is the need to better understand the in vivo n. -3 LC-PUFA biosynthetic capabilities of cultured fish to enable the possible maximization of dietary 18:3n. -3 (ALA) bioconversion to 20:5n. -3 (EPA) and 22:6n. -3 (DHA). The cofactors and coenzymes involved in this metabolic pathway have so far received limited research attention. In this study, juvenile Atlantic salmon were fed an ALA-rich diet with no, normal, or over-fortified inclusion of those micronutrients reported to be essential cofactors (iron; zinc; magnesium) and coenzymes (riboflavin; biotin; niacin) for the fatty acid elongase and desaturase enzymes. The results showed that reduced dietary inclusion of these micronutrients impaired the normal n. -3 LC-PUFA biosynthetic capabilities of fish, whereas the over fortification did not provide any additional benefit. This study provides new knowledge on micronutrients and lipid metabolism interactions in a commercially important cultured species, and is envisaged to be a useful contribution towards developing more sustainable and commercially viable aquafeed for the future.Statement of relevance. This work is the continuation and extension of a previous study (Lewis et al., 2013, Aquaculture 412/413, 215-222) in which we explored the physiological roles and potential effects of micronutrients on fatty acid metabolism in cultured fish. The present study differed from the previous in the blend of minerals and vitamins used, the species, the fatty acid composition of the test diet, and the inclusion also of a negative control. The results are most interesting, showing that riboflavin (B2), biotin (B7), and niacin (B3), Iron (Fe), Magnesium (Mg) and Zinc (Zn) are all required for proper fatty acid bioconversion, but also that a dietary over-fortification does not translate into proportional improved bioconversion.

Complex coacervation between flaxseed protein isolate and flaxseed gum

Flaxseed protein isolate (FPI) and flaxseed gum (FG) were extracted, and the electrostatic complexation between these two biopolymers was studied as a function of pH and FPI-to-FG ratio using turbidimetric and electrophoretic mobility (zeta potential) tests. The zeta potential values of FPI, FG, and their mixtures at the FPI-to-FG ratios of 1:1, 3:1, 5:1, 10:1, 15:1 were measured over a pH range 8.0-1.5. The alteration of the secondary structure of FPI as a function of pH was studied using circular dichroism. The proportion of a-helical structure decreased, whereas both β-sheet structure and random coil structure increased with the lowering of pH from 8.0 to 3.0. The acidic pH affected the secondary structure of FPI and the unfolding of helix conformation facilitated the complexation of FPI with FG. The optimum FPI-to-FG ratio for complex coacervation was found to be 3:1. The critical pH values associated with the formation of soluble (pHc) and insoluble (pHΦ1) complexes at the optimum FPI-to-FG ratio were found to be 6.0 and 4.5, respectively. The optimum pH (pHopt) for the optimum complex coacervation was 3.1. The instability and dissolution of FPI-FG complex coacervates started (pHΦ2) at pH2.1. These findings contribute to the development of FPI-FG complex coacervates as delivery vehicles for unstable albeit valuable nutrients such as omega-3 fatty acids.

Morphological and molecular investigations of the holocephalan elephant fish nephron: the existence of a countercurrent-like configuration and two separate diluting segments in the distal tubule

In marine cartilaginous fish, reabsorption of filtered urea by the kidney is essential for retaining a large amount of urea in their body. However, the mechanism for urea reabsorption is poorly understood due to the complexity of the kidney. To address this problem, we focused on elephant fish (Callorhinchus milii) for which a genome database is available, and conducted molecular mapping of membrane transporters along the different segments of the nephron. Basically, the nephron architecture of elephant fish was similar to that described for elasmobranch nephrons, but some unique features were observed. The late distal tubule (LDT), which corresponded to the fourth loop of the nephron, ran straight near the renal corpuscle, while it was convoluted around the tip of the loop. The ascending and descending limbs of the straight portion were closely apposed to each other and were arranged in a countercurrent fashion. The convoluted portion of LDT was tightly packed and enveloped by the larger convolution of the second loop that originated from the same renal corpuscle. In situ hybridization analysis demonstrated that co-localization of Na(+),K(+),2Cl(-) cotransporter 2 and Na(+)/K(+)-ATPase α1 subunit was observed in the early distal tubule and the posterior part of LDT, indicating the existence of two separate diluting segments. The diluting segments most likely facilitate NaCl absorption and thereby water reabsorption to elevate urea concentration in the filtrate, and subsequently contribute to efficient urea reabsorption in the final segment of the nephron, the collecting tubule, where urea transporter-1 was intensely localized.

Simultaneous crystallization and decomposition of PVA/MMT composites during non-isothermal process

Decomposition of poly(vinyl alcohol)/montmorillonite clay (PVA/MMT) composites during melting-crystallization was experimentally confirmed by morphology and molecular structure changes. In particular, FTIR spectra show the shift of O-H stretching band as well as enhanced intensities of C-O stretching and CH2 rocking vibrational modes. Furthermore, Raman deconvolution indicates that C-H wagging, CH2-CH wagging, CH-CO bending and CH2 wagging modes in amorphous domains were all decreased greatly. Moreover, this decomposition leads to decreased melting enthalpy, melting point, crystallization enthalpy and crystallization temperature. Crystallization analysis shows that the MMT incorporated slows down the crystallization process in the PVA matrix regardless of the nucleation capability of MMT. Despite the severe decomposition, the crystallization kinetics still corroborated well with common classical models. As a result, molecular structure changes and crystallization retardation observed in this study clearly indicate the strong effects of the thermal degradation on the non-isothermal crystallization of PVA/MMT composites.