Exceptional durability enhancement of PA/PBI based polymer electrolyte membrane fuel cells for high temperature operation at 200°C

The incorporation of phosphotungstic acid functionalized mesoporous silica in phosphoric acid doped polybenzimidazole (PA/PBI) substantially enhances the durability of PA/PBI based polymer electrolyte membrane fuel cells for high temperature operation at 200°C.

The microstructure evolution and softening processes during high-temperature deformation of a 21Cr-10Ni-3Mo duplex stainless steel

The austenite and ferrite microstructure evolution and softening mechanisms have been investigated in a 21Cr-10Ni-3Mo duplex stainless steel, containing about 60% austenite, deformed in torsion at 1200°C using a strain rate of 0.7 s-1. The above experimental conditions led to the formation of a small volume fraction of new austenite grains through discontinuous dynamic recrystallization (DDRX), which could not account for the observed large softening on the flow curve. DDRX grains mainly formed through the strain-induced migration of the pre-existing austenite grain boundaries, known to dominate in single-phase austenite, complemented by subgrain growth in the interface regions with ferrite. A significant portion of austenite dynamic softening has been attributed to the large-scale subgrain coalescence, the extent of which increased with strain, which seems to have contributed substantially to the observed flow stress decrease. The above process thus appears to represent an alternative mode of austenite dynamic softening to the classical DDRX in the duplex austenite/ferrite microstructure, characterised by limited availability of the pre-existing austenite/austenite high-angle boundaries, deformed at a high temperature. The softening mechanism within ferrite has been classified as "continuous DRX", characterised by a gradual increase in misorientations between neighbouring subgrains with strain and resulting in the progressive conversion of subgrains into "crystallites" bounded partly by low-angle and partly by large-angle boundaries.

Comparative study of the microstructures and mechanical properties of direct laser fabricated and arc-melted AlxCoCrFeNi high entropy alloys

High entropy alloys (HEA) are a relatively new metal alloy system that have promising potential in high temperature applications. These multi-component alloys are typically produced by arc-melting, requiring several remelts to achieve chemical homogeneity. Direct laser fabrication (DLF) is a rapid prototyping technique, which produces complex components from alloy powder by selectively melting micron-sized powder in successive layers. However, studies of the fabrication of complex alloys from simple elemental powder blends are sparse. In this study, DLF was employed to fabricate bulk samples of three alloys based on the AlxCoCrFeNi HEA system, where x was 0.3, 0.6 and 0.85M fraction of Al. This produced FCC, FCC/BCC and BCC crystal structures, respectively. Corresponding alloys were also produced by arc-melting, and all microstructures were characterised and compared longitudinal and transverse to the build/solidification direction by x-ray diffraction, glow discharge optical emission spectroscopy and scanning electron microscopy (EDX and EBSD). Strong similarities were observed between the single phase FCC and BCC alloys produced by both techniques, however the FCC/BCC structures differed significantly. This has been attributed to a difference in the solidification rate and thermal gradient in the melt pool between the two different techniques. Room temperature compression testing showed very similar mechanical behaviour and properties for the two different processing routes. DLF was concluded to be a successful technique to manufacture bulk HEA[U+05F3]s.

Thermal and physical properties of an archetypal organic ionic plastic crystal electrolyte

The thermal and mechanical properties of the ionic plastic crystal N-methyl-N-propylpyrrolidinium hexafluorophosphate have been investigated and the effect of adding a miscible polymer on the mechanical properties is reported. The physical properties of the pure plastic crystal are discussed in detail and for the first time the change in volume with temperature for an organic ionic plastic crystal is reported. An increase in volume in conjunction with increased conductivity supports the hypothesis that ion conduction within the plastic crystal proceeds via defects. For phase I and melting, the magnitude of the volume increase does not appear to be in accord with the subtle change in conductivity. This is suggested to be due to the presence of layer defects, which allow for correlated ionic motion, which does not increase the conductivity. Addition of polymer to the plastic crystal significantly increases the mechanical strength, decreases the conductivity, but has little effect on the phase behaviour, further supporting the hypothesis of vacancy-mediated conduction.

Miscibility, UV resistance, thermal degradation, and mechanical properties of PMMA/SAN blends and their composites with MWCNTs

Poly(methyl methacrylate)/poly(styrene-co-acrylonitrile) (PMMA/SAN) blends, with varying concentrations, were prepared by melt-mixing technique. The miscibility is ensured by fixing the acrylonitrile (AN) content of styrene acrylonitrile (SAN) as 25% by weight. The blends were transparent as well. The Fourier transform infrared spectroscopic (FTIR) studies did not reveal any specific interactions, supporting the well accepted 'copolymer repulsion effect' as the driving mechanism for miscibility. Addition of SAN increased the stability of PMMA towards ultraviolet (UV) radiations and thermal degradation. Incorporation of even 0.05% by weight of multi-walled carbon nanotubes (MWCNTs) significantly improved the UV absorbance and thermal stability. Moreover, the composites exhibited good strength and modulus. However, at higher concentrations of MWCNTs (0.5 and 1% by weight) the thermo-mechanical properties experienced deterioration, mainly due to the agglomeration of MWCNTs. It was observed that composites with 0.05% by weight of finely dispersed and well distributed MWCNTs provided excellent protection in most extreme climatic conditions. Thus, PMMA/SAN/MWCNTs composites can act as excellent light screens and may be useful, as cost-effective UV absorbers, in the outdoor applications.

High-performance composite from epoxy and glass fibers : morphology, mechanical, dynamic mechanical, and thermal analysis

Diglycidyl ether of bisphenol-A type epoxy resin cured with diamino diphenyl sulfone was used as the matrix for fiber-reinforced composites to get improved mechanical and thermal properties for the resulting composites. E-glass fiber was used for fiber reinforcement. The morphology, tensile, flexural, impact, dynamic mechanical, and thermal properties of the composites were analyzed. The tensile, flexural, and impact properties showed dramatic improvement with the addition of glass fibers. Dynamic mechanical analysis was performed to obtain the Tg of the cured matrix as well as the composites. The improved thermal stability of the composites was clear from the thermogravimetric analysis. Scanning electron micrographs were taken to understand the interfacial adhesion between the fiber and the matrix. The values of mechanical properties were compared with modified epoxy resin composite system. Predictive models were applied using various equations to compare the mechanical data obtained theoretically and experimentally.

Effect of baking process on microstructures and mechanical properties of low silicon TRIP steel sheet with niobium

After 2% predeformation, the baking treatment with different schedule was carried out for low silicon TRIP steel sheet with niobium. The effects of baking temperature and time on microstructures and mechanical properties were investigated. The results showed that with increasing the baking temperature and time, the volume fraction of retained austenite decreases, and the volume fraction of tempered martensite increases; as baking temperature ranges from 80°C to 170°C, the bake-hardening (BH) value increases obviously, while from 170°C to 230°C, the variation of BH value is very slight; as baking time ranges from 2 min to 20 min, the BH value increases significantly, while the BH value decreases when baking time exceeds 20 min. So that when the baking temperature is 170°C and the baking time is 20 min, the low silicon TRIP steel sheet exhibits good bake-hardening behavior, and the highest BH value is above 70 MPa.

Assessment of performance properties of wetsuits

Wetsuits are an integral part of surfing especially in the southern regions of Australia. There is currently little information about mechanical, comfort and thermal properties of wetsuits. There is a demand from wetsuit manufacturers to better understand the neoprene properties and wetsuit performance. The performance characteristics of eight topselling wetsuits, from both high end and low end of the market, were examined. These characteristics include thickness, elasticity, bursting strength, hydrophobicity, thermal conductivity and seal strength. Tensile assessment revealed that neoprene foam was strong and its stretch recovery was well beyond 1.6 times of the original length. Neoprene was found to be hydrophobic with very low surface energy. High-end wetsuits with higher thickness showed slightly higher thermal resistance than low-end wetsuits, indicating that both thickness and bulk density of neoprene influenced thermal properties. High-end wetsuits with fluid seal were stronger than low-end wetsuits with stitched seal.

Effect of zwitterions on electrochemical properties of oligoether-based electrolytes

Solid polymer electrolytes show great potential in electrochemical devices. Poly(ethylene oxide) (PEO) has been studied as a matrix for solid polymer electrolytes because it has relatively high ionic conductivity. In order to investigate the effect of zwitterions on the electrochemical properties of poly(ethylene glycol) dimethyl ether (G5)/lithium bis(fluorosulfonyl) amide (LiFSA) electrolytes, a liquid zwitterion (ImZ2) was added to the G5-based electrolytes. In this study, G5, which is a small oligomer, was used as a model compound for PEO matrices. The thermal properties, ionic conductivity, and electrochemical stability of the electrolytes with ImZ2 were evaluated. The thermal stabilities of all the G5-based electrolytes with ImZ2 were above 150 °C, and the ionic conductivity values were in the range of 0.8–3.0 mS cm−1 at room temperature. When the electrolytes contained less than 5.5 wt% ImZ2, the ionic conductivity values were almost the same as that of the electrolyte without ImZ2. The electrochemical properties were improved with the incorporation of ImZ2. The anodic limit of the electrolyte with 5.5 wt% ImZ2 was 5.3 V vs. Li/Li+, which was over 1 V higher than that of G5/LiFSA.

Effect of temperature on mechanical behaviour of high manganese TWIP steel

The aim of the present study was to investigate the role of deformation temperature on the active deformation mechanisms in a 0.6C-18Mn-1.5Al (wt%) TWIP steel. The tensile testing was performed at different temperatures, ranging from ambient to 400°C at a constant strain rate of 10-3 S-1. The microstructure characterization was carried out using a scanning electron microscopy. The deformation temperature revealed a significant effect on the active deformation mechanisms (i.e. slip versus twinning), resulting in different microstructure evolution and mechanical properties. At the room temperature, the mechanical twinning was the dominant deformation mechanism, enhancing both the strength and ductility. Dynamic strain aging (DSA) effect was observed at different deformation temperatures, though it was more pronounced at higher temperatures. The volume fraction of deformation twins significantly reduced with an increase in the deformation temperature, deteriorating the mechanical behavior. There was a transition temperature (~300°C), above which the mechanical twinning was hardly observed in the microstructure even at fracture, resulting in low ductility and strength. The current observation can be explained through the change in the stacking fault energy with the deformation temperature. © (2014) Trans Tech Publications, Switzerland.

One-pot synthesis of aminated multi-walled carbon nanotube using thiol-ene click chemistry for improvement of epoxy nanocomposites properties

A non-oxidative method based on thiol-ene click chemistry for functionalization of multi-walled carbon nanotube (CNT) was performed in order to improve the interfacial interactions between epoxy matrix and CNT. In this way, the CNT was aminated using 2-aminoethanethiol hydrochloride radicals thermally produced by a peroxide radical initiator. The aminated CNT (CNT-NH2) was characterized by FTIR, TGA, and solubility evaluations, confirming that thiol radicals are successfully grafted onto the CNT surface with a proper yield. Various percentages of pure CNT (p-CNT) and CNT-NH2 were then incorporated into epoxy matrix to evaluate the effect of the functionalization of CNT on thermal, mechanical, and morphological properties. The nanocomposites were characterized by DMA, tensile testing, and TGA. Results showed that glass transition temperature, tensile properties and thermal stability of epoxy nanocomposites containing CNT-NH2 improves significantly compared to those containing unmodified CNT. These results prove the role of amino-functionalization in improving the interfacial adhesion between epoxy and CNT, which was further confirmed by morphological observations of fracture surfaces of the nanocomposites.