Effect of transformation mechanism (static or dynamic) on final ferrite grain size

A simple series of test was developed to highlight and compare the difference between the static strain induced transformation (SSIT) and the dynamic strain induced transformation (DSIT) mechanism in grain refinement and also to investigate the origin of the difference between the two mechanisms. The results showed that while the SSIT sets up a two-dimensional impingement among the ferrite grains, it cannot avoid their coarsening (normal growth). However, the DSIT forms a group of grains with a three-dimensional impingement which does not coarsen and maintains their fine size throughout the transformation, thereby, reduces the final average grain size.

High performance mg alloy by grain refinement

Mg alloys are one of promising eco-materials. The present paper describes the importance of grain refinement to develop high performance Mg alloys. The fine-grained Mg alloys exhibit not only a good combination of high strength and high ductility at room temperature, but also high formability (superplasticity) at elevated temperatures.

Role of grain boundary sliding in the anisotropy of magnesium alloys

The plastic anisotropy of magnesium alloy sheet drops rapidly with test temperature. It has previously been suggested that this may be due to an increase in the activity of (c+a) dislocations. The present note points out that the phenomenon may result, instead, from the action of grain boundary sliding. This can explain the strong effect of grain size on anisotropy. Furthermore, it points to a new avenue for alloy development.

Effect of grain size on the performance of extruded magnesium alloy tubes in three-point bending

The performance of extruded AZ31, AZ61 and AM-EX1 tubes was examined in three-point bending. Different extrusion temperatures were used to investigate the effect of grain size on the load-carrying capacity, energy absorption and fracture propensity of the tubes. Results showed that while the peak load increased with a smaller average recrystallised grain size, the retention of large elongated un-recrystallised grains in the microstructure reduced the load. The presence of the large elongated grains also appeared detrimental to the ability of the tube to deform before fracture.

Simultaneously enhanced strength and ductility of titanium via multimodal grain structure

Commercial Ti with a multimodal grain structure was successfully produced using cryorolling, followed by low-temperature annealing. This multimodal grain structure Ti exhibited a combination of high yield strength (926 MPa), a uniform elongation of 11% and a failure elongation of 23%. The strength enhancement was mainly derived from the ultrafine equiaxed grains, while the improved ductility originated from the large fraction of high-angle grain boundaries and the multimodal grain structure.

Influence of grain supplements during winter on liveweight, mohair growth and mohair quality of weaner Angora goats

To identify methods to improve growth and mohair production of weaned Angora goats (mean liveweight 18-20 kg) during their first winter, two supplementary feeding experiments using whole-grain barley and lupins were conducted on a farm in southern New South Wales, in a region where weaner illthrift had been reported. Experiment 1 was a 2×2 + 1 factorial with 16 replicate goats; two feeding levels (115 or 230 g/day of whole-barley grain)× two periods of feeding (4 or 8 weeks) + Control (grazing only). Experiment 2 had five treatments × 13 replicate goats; three treatments fed 230 g/day of whole-barley grain for periods of 2 or 3 months and two treatments fed a 50:50 mixture of lupin and barley grain at 350 g/day for 2 or 4 months. Goats were individually fed and then all returned together for grazing. There were no effects of feeding in Experiment 1 and variations of feeding 230 g/day of barley in Experiment 2 provided no benefit. Feeding lupin/barley for 4 months increased liveweight (gain 59 g/day), mohair production, mohair fibre diameter and the incidence of medullated fibre. About 25% of this ration was not eaten by eight goats, reducing treatment average intake to 295 g/day. By the end of spring, there was no difference in treatment liveweights. Regression constants indicated that for each 1 μm increase in mean fibre diameter, greasy fleece weight increased 35 g and for each 1 kg increase in pre-shearing liveweight, greasy fleece weight increased 26 g. The results show that Angora weaner goats can grow during winter, provided their energy and protein needs for growth are met. Improved pasture management and higher levels of supplementary feeding to weaned Angoras are indicated compared with current practices on farms in Australia.

Influence of grain size on twinning in two hcp metals

Deformation twinning behaviour in differently grain sized samples of a commercial pure titanium and a magenisum alloy is investigated. In some aspects the phenomenology of twinning differs between the two materials while in others both materials show a similar response. Nucleation density per unit of nucleating interface and twin aspect ratio scale with applied stress. The impact of grain size on twin volume fraction is modelled analytically.

Automatic grain texture analysis using integral transforms

Tonewood for musical instruments is quarter-sawn and frequently quality-graded based on visual appearance, mechanical and acoustic properties. The assessment uses simple human (subjective) observation, and two ‘‘experts’’ can rate the same sample differently. This paper describes the application of integral transforms (Fourier and Radon) for automatic (objective) assessment of the visual appearance of 10 Sitka spruce (Picea sitchensis) sample images. This work considers surface classification on the basis of grain orientation, count, spacing, and evenness or uniformity.

Effect of grain size on corrosion of high purity aluminium

A complete understanding of how grain refinement, grain size, and processing affect the corrosion resistance of different alloys has not yet been fully developed. Determining a definitive 'grain size-corrosion resistance' relationship, if one exists, is inherently complex as the processing needed to achieve grain refinement also imparts other changes to the microstructure (such as texture, internal stress, and impurity segregation). This work evaluates how variation in grain size and processing impact the corrosion resistance of high purity aluminium. Aluminium samples with a range of grain sizes, from ∼100 μm to ∼2000 μm, were produced using different processing routes, including cold rolling, cryo rolling, equal channel angular pressing, and surface mechanical attrition treatment. Evaluation of all the samples studied revealed a tendency for corrosion rate to decrease as grain size decreases. This suggests that a Hall-Petch type relationship may exist for corrosion rate and grain size. This phenomenon, discussed in the context of grain refinement and processing, reveals several interesting and fundamental relationships.

Sensitivity of deformation twinning to grain size in titanium and magnesium

The impact of grain size on deformation twinning in commercial purity titanium and magnesium alloy Mg–3Al–1Zn (AZ31) is investigated. Tensile tests were carried out for the titanium samples; compression testing was employed for the magnesium specimens. Average values of the true twin length, true twin thickness and the number density of twins were determined using stereology. A key difference between these two materials is that twinning contributes little to the plastic strain in the titanium while it accounts for nearly all of the early plastic strain in the magnesium. In some respects (e.g. volume fraction and number density) the phenomenology of twinning differed between the two materials, while in others (e.g. twin shape and size) both materials showed a similar response. It is found that in both materials, twins span the entirety of their parent grains only for grain sizes less than ∼30 μm. Both the nucleation density per unit of nucleating interface (i.e. grain and twin boundaries) and the aspect ratio of twins scale with applied stress. The impact of grain size on twin volume fraction is modelled analytically.

Modelling the combined effect of grain size and grain shape on plastic anisotropy of metals

Within each columnar grain of a metallic film, the resistance to dislocation glide varies in function of the orientation of the slip plane with regard to the grain long axis. Plastic slip is impeded across grain boundaries and this contributes to the anisotropy of the overall mechanical response. A simplified (Taylor-type) crystal plasticity model is proposed that accounts for such effect of grain shape on the slip system selection. Assuming that dislocation density gradients are normal to the grain boundaries, backstresses developed at the onset of plasticity are estimated based on two definitions of the effective grain boundary spacing ‘‘seen’’ by individual slip systems. The first one reduces to the mean area-to-perimeter ratio of cross-sections of the grain cut parallel to the slip plane. Closed-form expressions of the average backstresses developed inside grains with spheroidal shapes are introduced in the crystal hardening law. The model reproduces the very high plastic anisotropy of electro-deposited pure iron with a strong c-fiber and a refined columnar grain structure [Yoshinaga, N., Sugiura, N., Hiwatashi, S., Ushioda, K., Kada, O., 2008. Deep drawability of electro-deposited pure iron having an extremely sharp h111i//ND texture. ISIJ Int. 48, 667–670]. It also provides valid estimates of the texture development and the influence of grain size on the yield strength.

Effective grain orientation on the substructure development of 304 stainless steel and NA-30% fe

This data is the result of an investigation into the effect of grain orientation on the substructure development of 304 stainless steel and a Ni-30wt.%Fe alloy. Both alloys have been used as model alloys to study the high temperature deformation of austenite. The development of the dislocation substructure as a function of strain, temperature and grain orientation was investigated using a combination of electron backscatterd diffraction (EBSD) and transmission electron microscopy (TEM).