Role of microstructure in the low cycle fatigue of multi-phase steels

The low cycle fatigue (LCF) behaviour of several commercially-produced multiphase steels was studied; including dual-phase (DP) and transformation induced plasticity (TRIP). In addition, a novel TRIP980 hybrid microstructure was examined that consisted of coarse ferrite grains along with low temperature bainite regions interspersed with retained austenite. Fully reversed strain controlled fatigue tests were conducted on the different steels to determine the cyclic stress response and strain to failure. The effects of the cyclic deformation on the microstructures were analysed using electron backscattered diffraction (EBSD) and X-ray diffraction (XRD). Results showed that the initial cyclic hardening behaviour and low cyclic softening ratio observed in the TRIP steels was not necessarily due to austenite to martensite transformation. Differences between the austenite transformation behaviour of the conventional and novel hybrid TRIP microstructures was related to the different surrounding phases and the size of the retained austenite.

The formation of complex microstructures after different deformation modes in advanced high-strength steels

The microstructure of transformation induced plasticity (TRIP) and dual phase (DP) multiphase steels after stamping of an industrial component at different strain levels was investigated using transmission electron microscopy. The TRIP steel microstructure showed a more complex dislocation substructure of ferrite at different strain levels than DP steel. The deformation microstructure of the stamped parts was compared to the deformation microstructure in these complex steels for different "equivalent" tensile strains. It was found that the microstructures are similar only at high levels of strain (>10 pct) for both steels. © 2014 The Minerals, Metals & Materials Society and ASM International.

Microstructure modeling and prediction of the mechanical properties of advanced high strength steels

Dual phase (DP) steels were modeled using 2D and 3D representative volume elements (RVE). Both the 2D and 3D models were generated using the Monte-Carlo-Potts method to represent the realistic microstructural details. In the 2D model, a balance between computational efficiency and required accuracy in truly representing heterogeneous microstructure was achieved. In the 3D model, a stochastic template was used to generate a model with high spatial fidelity. The 2D model proved to be efficient for characterization of the mechanical properties of a DP steel where the effect of phase distribution, morphology and strain partitioning was studied. In contrast, the current 3D modeling technique was inefficient and impractical due to significant time cost. It is shown that the newly proposed 2D model generation technique is versatile and sufficiently accurate to capture mechanical properties of steels with heterogeneous microstructure.

Multiphase material modelling by multiscale particle-in-cell method

A particle-based method for multiscale modeling of multiphase materials such as Dual Phase (DP) and Transformation Induced Plasticity (TRIP) steels has been developed. The multiscale Particle-In-Cell (PIC) method benefits from the many advantages of the FEM and mesh-free methods, and to bridge the micro and macro scales through homogenization. The conventional mesh-based modeling methods fail to give reasonable and accurate predictions for materials with complex microstructures. Alternatively in the multiscale PIC method, the Lagrangian particles moving in an Eulerian grid represent the material deformation at both the micro and macro scales. The uniaxial tension test of two phase and three-phase materials was simulated and compared with FE based simulations. The predictions using multiscale PIC method showed that accuracy of field variables could be improved by up to 7%. This can lead to more accurate forming and springback predictions for materials with important multiphase microstructural effects.

Strain hardening behavior of high performance FBDP, TRIP and TWIP steels

Based on n-value differential equation and microstructural observation, strain hardening behaviors of FBDP, TRIP, and TWIP steels during uniaxial tension were investigated. TRIP steel exhibits both superior strength and ductility than FBDP steel, and TWIP steel displays much higher total and uniform elongations in comparison to FBDP and TRIP steels. The instantaneous n values of FBDP and TRIP steels increase at small strains, reach a maximum value, smoothly decrease at higher strains, and then rapidly drop up to the specimen rupture. The strain hardening of TRIP steel persists at higher strains where that of FBDP steel begins to diminish. TWIP steel exhibits gradually increased instantaneous n values over the whole uniform plastic deformation, implying that TWIP steel shows a much larger strain hardening capability than FBDP and TRIP steels.

Numerical investigation of influence of the Martensite Volume Fraction on dp steels fracture behavior on the basis of digital material representation model

Development of the methodology for creating reliable digital material representation (DMR) models of dual-phase steels and investigation of influence of the martensite volume fraction on fracture behavior under tensile load are the main goals of the paper. First, an approach based on image processing algorithms for creating a DMR is described. Then, obtained digital microstructures are used as input for the numerical model of deformation, which takes into account mechanisms of ductile fracture. Ferrite and martensite material model parameters are evaluated on the basis of micropillar compression tests. Finally, the model is used to investigate the impact of the martensite volume fraction on the DP steel behavior under plastic deformation. Results of calculations are presented and discussed in the paper.

Precipitate characterisation of an advanced high-strength low-alloy (HSLA) steel using atom probe tomography

Increased fuel economy, combined with the need for the improved safety has generated the development of new hot-rolled high-strength low-alloy (HSLA) and multiphase steels such as dual-phase or transformation-induced plasticity steels with improved ductility without sacrificing strength and crash resistance. However, the modern multiphase steels with good strength-ductility balance showed deteriorated stretch-flangeability due to the stress concentration region between the soft ferrite and hard martensite phases [1]. Ferritic, hot-rolled steels can provide good local elongation and, in turn, good stretch-flangeability [2]. However, conventional HSLA ferritic steels only have a tensile strength of not, vert, similar600 MPa, while steels for the automotive industry are now required to have a high tensile strength of not, vert, similar780 MPa, with excellent elongation and stretch-flangeability [1]. This level of strength and stretch-flangeability can only be achieved by precipitation hardening of the ferrite matrix with very fine precipitates and by ferrite grain refinement. It has been suggested that Mo [3] and Ti [4] should be added to form carbides and decrease the coiling temperature to 650 °C since only a low precipitation temperature can provide the precipitation refinement [4]. These particles appeared to be (Ti, Mo)C, with a cubic lattice and a parameter of 0.433 nm, and they were aligned in rows [4]. It was reported [4] that the formation of these very fine carbides led to an increase in strength of not, vert, similar300 MPa. However, the detailed analysis of these particles has not been performed to date due to their nanoscale size. The aim of this work was to carry out a detailed investigation using atom probe tomography (APT) of precipitates formed in hot-rolled low-carbon steel containing additions Ti and Mo.

The investigated low-carbon steel, containing Fe–0.1C–1.24Mn–0.03Si–0.11Cr–0.11Mo–0.09Ti–0.091Al at.%, was produced by hot rolling. The processing route has been described in detail elsewhere [5] European Patent Application, 1616970 A1, 18.01.2006.[5]. The microstructure was characterised by transmission electron microscopy (TEM) on a Philips CM 20, operated at 200 kV using thin foil and carbon replica techniques. Qualitative energy dispersive X-ray spectroscopy (EDXS) was used to analyse the chemical composition of particles. The atomic level of particle characterisation was performed at the University of Sydney using a local electrode atom probe [6]. APT was carried out using a pulse repetition rate of 200 kHz and a 20% pulse fraction on the sample with temperature of 80 K. The extent of solute-enriched regions (radius of gyration) and the local solute concentrations in these regions were estimated using the maximum separation envelope method with a grid spacing of 0.1 nm [7]. A maximum separation distance between the atoms of interest of dmax = 1 nm was used.

The microstructure of the steel consisted of two types of fine ferrite grains: (i) small recrystallised grains with an average grain size of 1.4 ± 0.2 μm; and (ii) grains with a high dislocation density (5.8 ± 1.4 × 1014 m−2) and an average grain size of 1.9 ± 0.1 μm in thickness and 2.7 ± 0.1 μm in length (Fig. 1a). Some grains with high dislocation density displayed an elongated shape with Widmanstätten side plates and also the formation of cells and subgrains (Fig. 1a). The volume fraction of recrystallised grains was 34 ± 8%.

Influence of low-strain deformation characteristics of high strength sheet steel on curl and springback in bend-under-tension tests

The influence of low-strain deformation behavior on curl and springback in advanced high strength steels (AHSS) was assessed using a bend-under-tension test. The effect of yielding behavior on curl and springback was examined by heat-treating two dual-phase steels to induce yield point elongation, while keeping a relatively constant tensile strength and a constant sheet thickness. A dual-phase and TRIP steel with similar initial thickness and tensile strengths were also examined to investigate the effect of work-hardening on curl and springback. It is shown that while current understanding limits prediction of curl and springback in bending under tension using only the initial sheet thickness and tensile strength, both the yielding and work-hardening behavior can affect the results. Explanations for these effects are proposed in terms of the discontinuous yielding and flow stress in the materials.

Experimental evaluation of curl and tensile properties of advanced high strength sheet steels

The response of HSLA steel, 590R, and dual-phase steel, DP-600, to non-uniform deformation imposed in a laboratory Bending-Under-Tension (BUT) test apparatus was evaluated. Samples were deformed with both low and high back tension forces at bend angles of 45 and 90 degrees, and evaluated to determine the ""side-wall curl,"" i.e., the curvature in the sheet section in contact with the die. The results indicate that there are no consistent differences between the two steels, 590R and DP-600. It was found that back tension, tensile strength and sheet thickness were the primary factors affecting curl. The bend angle has an influence on curl, with the curl radius at a 90ø bend angle being greater than the curl radius at a 45\mD bend angle.

Using the solid-shell element to model the roll forming of large radii profiles

Roll forming is an incremental bending process for forming metal sheet, strip or coiled stock. Although Finite Element Analysis (FEA) is a standard tool for metal forming simulation, it is only now being increasingly used for the analysis of the roll forming process. This is because of the excessive computational time due to the long strip length and the multiple numbers of stands that have to be modelled. Typically a single solid element is used through the thickness of the sheet for roll forming simulations. Recent investigations have shown that residual stresses introduced during steel processing may affect the roll forming process and therefore need to be included in roll forming simulations. These residual stresses vary in intensity through the thickness and this cannot be accounted for by using only one solid element through the material thickness, in this work a solid-shell element with an arbitrary number of integration points has been used to simulate the roll forming process. The system modelled is that of roll forming a V-channel with dual phase DP780 sheet steel. In addition, the influence of other modelling parameters, such as friction, on CPU time is further investigated. The numerical results are compared to experimental data and a good correlation has been observed. Additionally the numerical results show that the CPU time is reduced in the model without friction and that considering friction does not have a significant effect on springback prediction in the numerical analysis of the roll forming process.

Machinability and phase transformation study of nanobainite steels

There is an increasing demand for high strength materials with the development of technology and critical applications. Nano materials are newly developed materials with extremely high strength for this purpose. Nanobainite is a dual phase material containing alternate layers of bainitic ferrite in nano dimensions and retained austenite. Nanobainite is produced by isothermally holding austenitized steel at a temperature of 200°C or less, depending on the chemical composition, for 6 10 days until bainite forms and then cooling to room temperature using austempering. The experimental design consisted of face milling under 12 combinations of Depth of Cut (DOC)-1, 2 and 3mm; cutting speed-100 and 150m/min; constant feed-0.15mm/rev and coolant on/off. The machinability of the material is assessed by means of analysis, such as surface texture and microhardness. The assessment also involves microstructural comparisons before and after milling. Future work involves quantifying the microstructural phase before and after milling using XRD. The results obtained are used to assess the most favorable condition to cut this new variety of steel.

A preliminary study on machinability assessment of nanobainite steel

The demand for high strength materials and improvements in heat treatment techniques has given rise to this new form of high strength steel known as nanobainite steel. The production of nanobainite steel involves slow isothermal holding of austenitic steel around 200oC for 10 days, in order to obtain a carbon enriched austenite and cooling to room temperature using austempering. The microstructure of nanobainite steel is dual phase consisting of alternate layers of bainitic ferrite and austenite. The experimental design consists of face milling under 12 combination of Depth of Cut (DoC)-1, 2 and 3mm; cutting speed-100 and 150m/min; constant feed- 0.15mm/rev and coolant on/off. The machinability of the material is assessed by means of analysis such as metallography and cutting force analysis. The results obtained are used to assess the most favorable condition to machine this new variety of steel. Future work involves study on phase transformation by quantifying the microstructural phase before and after milling using XRD.