Effect of pre-straining and bake hardening on the microstructure and mechanical properties of CMnSi trip steels

The effects of pre-straining and bake hardening on the mechanical behaviour and microstructural changes were studied in two CMnSi TRansformation-Induced Plasticity (TRIP) steels with different microstructures after intercritical annealing. The TRIP steels before and after pre-straining and bake hardening were characterised by X-ray diffraction, optical microscopy, transmission electron microscopy, three dimensional atom probe and tensile tests. Both steels exhibited discontinuous yielding behaviour and a significant strength increase with some reduction in ductility after pre-straining and bake hardening treatment. The following main microstructural changes are responsible for the observed mechanical behaviours: a decrease in the volume fl:action of retained austenite, a increase in the dislocation density and the formation of cell substructure in the polygonal ferrite, higher localized dislocation density in the polygonal ferrite regions adjacent to martensite or retained austenite, and the precipitation of fine iron carbides in bainite and martensite. The mechanism for the observed yield point phenomenon in both steels after treatment was analysed.

The microstructure evolution and mechanical properties of cryorolled Al alloys

A solutionized Al2024 alloy was subjected to rolling at liquid nitrogen temperature (cryorolling) resulting in an ultra-fine stmcture. The material was also subjected to recovery annealing at 160°C. The ultrafine structured material demonstrated increased strength but very low ductility. The uniform elongation of the material after recovery annealing increased without any sacrifice of strength.

The effect of hydrogenation on the ECAP compaction of Ti–6Al–4V powder and the mechanical properties of compacts

The effect of hydrogen content on the compaction of Ti–6Al–4V powder at low temperatures, namely 500 °C, using equal channel angular pressing (ECAP) with back pressure has been investigated. The properties of the compacts before and after a heat treatment and de-hydrogenation cycle have been determined. Compaction of powder by ECAP (500 °C and 260 MPa) has shown maximum levels of relative density of 99.3% and 99.4% when charged with 0.05–0.1 wt.% and 0.61–0.85 wt.% of hydrogen, respectively. After the de-hydrogenation heat treatment the diffusion bonding between individual powder particles was completed and the microstructure was altered, depending on the level of hydrogen content. Two local maxima of 99.2% and 98.1% were observed in the measured density of consolidated compacts for hydrogen contents between 0.05 wt.% and 0.1 wt.% and between 0.61 wt.% and 0.85 wt.%, respectively. However, the mechanical properties of the compacts within these two ranges of hydrogen content were significantly different due to a difference in the observed microstructure. An exceptionally high ductility of 29%, in combination with a relatively high strength of ~560 MPa, was measured in a shear punch test on specimens which had a prior hydrogen level of 0.05 wt.% before the heat treatment. It was shown that material consolidated from powder hydrogenated to low levels of hydrogen before compaction has the potential to offer substantial improvements in mechanical properties after a suitable heat treatment.

Playing the Agnes : Hester Thrale-Piozzi and Frances Burney

Guided by the feminist intention of reasserting the importance of neglected female writers, I have used this work to re-examine the lives and texts of eighteenth-century diarists Hester Thrale-Piozzi and Frances Burney. Adopting an interdisciplinary methodology, I draw on both literary and non-literary material to examine the effect of familial and social patriarchy in eighteenth-century England. Using the diaries, journals and letters of Hester and Frances, I ask why female conformity to masculine domination was expected, and how violence was used to extract subserviant behaviour from women. Beginning with gossip, and encompassing social, editorial and physical abuse, I use the medical profession's manipulation of female vulnerability to exemplify the way society legitimates violence to ensure female ductility. Moving beyond this physical aspect, I then examine the psychical, and question the existence of a ‘self’ which is vulnerable to external manipulation. By diverging from the influence of Freudian psychology, and developing a form of Jungian feminism, I propose the existence of an essential female Self which transcends the constraints of societal expectations and physical violence. In this work, both Hester and Frances emerge as physically and psychically strong entities who were forced to adopt socially conformist personae to survive.

Effect of pre-straining and bake hardening on the microstructure and mechanical properties of CMnSi trip steels

The effects of pre-straining and bake hardening on the mechanical behaviour and microstructural changes were studied in two CMnSi TRansformation-Induced Plasticity (TRIP) steels with different microstructures after intercritical annealing. The TRIP steels before and after pre-straining and bake hardening were characterised by X-ray diffraction, optical microscopy, transmission electron microscopy, three dimensional atom probe and tensile tests. Both steels exhibited discontinuous yielding behaviour and a significant strength increase with some reduction in ductility after pre-straining and bake hardening treatment. The following main microstructural changes are responsible for the observed mechanical behaviours: a decrease in the volume fraction of retained austenite, an increase in the dislocation density and the formation of cell substructure in the polygonal ferrite, higher localized dislocation density in the polygonal ferrite regions adjacent to martensite or retained austenite, and the precipitation of fine iron carbides in bainite and martensite. The mechanism for the observed yield point phenomenon in both steels after treatment was analysed.

Porous TiNbZr alloy scaffolds for biomedical applications

In the present study, porous Ti–10Nb–10Zr alloy scaffolds with different porosities were successfully fabricated by a ‘‘space-holder” sintering method. By the addition of biocompatible alloying elements the porous TiNbZr scaffolds achieved significantly higher strength than unalloyed Ti scaffolds of the same porosity. In particular, the porous TiNbZr alloy with 59% porosity exhibited an elastic modulus and plateau stress of 5.6 GPa and 137 MPa, respectively. The porous alloys exhibited excellent ductility during compression tests and the deformation mechanism is mainly governed by bending and buckling of the struts. Cell cultures revealed that SaOS2 osteoblast-like cells grew on the surface and inside the pores and showed good spreading. Cell viability for the porous scaffold was three times higher than the solid counterpart. The present study has demonstrated that the porous TiNbZr alloy scaffolds are promising scaffold biomaterials for
bone tissue engineering by virtue of their appropriate mechanical properties, highly porous structure and excellent biocompatibility.

Deep drawing behaviour of ultrafine grained copper : modelling and experiment

Ultrafine grained materials produced by severe plastic deformation methods possess attractive mechanical properties such as high strength compared with traditional coarse grained counterparts and reasonable ductility. Between existing severe plastic deformation methods the Equal Channel Angular Pressing is the most promising for future industrial applications and can produce a variety of ultrafine grained microstructures in materials depending on route, temperature and number of passes during processing. Driven by a rising trend of miniaturisation of parts these materials are promising candidates for microforming processes. Considering that bi-axial deformation of sheet (foil) is the major operation in microforming, the investigation of the influence of the number of ECAP passes on the bi-axial ductility in micro deep drawing test has been examined by experiments and FE simulation in this study. The experiments have showed that high force was required for drawing of the samples processed by ECAP compare to coarse grained materials. The limit drawing ratio of ultrafine grained samples was in the range of 1.9–2.0 with ECAP pass number changing from 1 to 16, while a higher value of 2.2 was obtained for coarse grained copper. However, the notable decrease in tensile ductility with increase in strength was not as pronounced for bi-axial ductility. The FE simulation using standard isotropic hardening model and von Mises yielding criterion confirmed these findings.

High performance mg alloy by grain refinement

Mg alloys are one of promising eco-materials. The present paper describes the importance of grain refinement to develop high performance Mg alloys. The fine-grained Mg alloys exhibit not only a good combination of high strength and high ductility at room temperature, but also high formability (superplasticity) at elevated temperatures.

Microstructure and mechanical properties of thermomechanically processed TRansformation Induced Plasticity (TRIP) steels

One of the main aims of steel research for the automotive industry is to develop materials with the optimum combination of relevant properties, cost and productivity. The introduction of new TRansformation Induced Plasticity steels has been driven by the requirements to increase the ductility without compromising the strength. The main phenomenon responsible for the unique mechanical properties in these steels has been proposed to be the formation of multiphase structure, which can contribute to an increase in elongation during straining. The thesis studied the effect of the different alloying additions on the structure-property relationship in the TRIP steels.

Prediction of ductile fracture in the cold forging of steel

The thesis describes the development of a model of the cold forging process that accurately predicts the initiation of ductile fracture. The effect of the deformation history of the material during multiple forming operations is considered. Both two- and three-dimensional numerical models of the forging process were combined with a ductile fracture criterion to predict the material ductility and damage distribution in the workpiece.

Multi-scale modelling of DP590 steel

Dual Phase (DP) steel one of the Advanced High Strength Steels (AHSS) has a two phase microstructure where soft and hard phase acts together to offer a high strength composite effect. The high strength, however, must be balanced with ductility so that complex parts and designs can be manufactured from AHSS sheets. However, during forming certain grades of DP steel a sudden crack can occur without any intimation of necking. Thus, due to this abnormal forming behaviour, is difficult to accurately predict because most classical modelling approaches are not designed for such micro-structurally heterogeneous materials. These modelling approaches are generally based on an average representation of the material behaviour in a continuum mechanics formulation. This works for materials that are homogenous, or at least could be assumed to be homogenous at scales lower than the naked eye can see. However, for a material like AHSS, the microstructure plays a significant role in dictating the mechanical behaviour at the macro-scale. This paper studies the multi-scale modelling ofDP590 steel. It is found that the sufficient accuracy can be achieved from multi-scale modelling while comparing with the experiments.

Cyclic deformation behaviour of ultrfine-grained aluminium

Ultrafine-grained aluminium was produced by cryo-rolling and their deformation response under cyclic loading was investigated. Shear banding and grain coarsening were recognized as the main damage mechanism reducing their performance under cyclic loading. However presence of precipitates in ultrafine-grained A1 can actively hinder the operation of cyclic softening mechanisms and increase microstructural stability under cyclic loading.

Constitutive modeling of TWIP steel in uni-axial tension

High Mn steels demonstrate an exceptional combination of high strength and ductility due to their high work hardening rate during deformation. The microstructure evolution and work hardening behavior of Fe18Mn0.6C1.5Al TWIP steel in uni-axial tension were examined. The purpose of this study was to determine the contribution of all the relevant deformation mechanism : slip, twinning and dynamic strain aging. Constitutive modeling was carried out based on the Kubin-Estrin model, in which the densities of mobile and forest dislocations are coupled in order to account for the continuous immobilization of mobile dislocations during straining. These coupled dislocation densities were also used for simulating the contribution of dynamic strain aging on the flow stress. The model was modified to include the effect of twinning.

Effect of manufacturing process on the final properties of advanced high strength steels for automotive applications

The performance of multiphase steels with high strength and improved toughness or ductility, such as intercritically annealed dual-phase (DP) and transformation-induced plasticity (TRIP) steels, is of key importance to the automotive industry. In this work we have considered the entire manufacturing process and the effects of this on the final product performance. These steels are formed to produce the required final shape and then the car is paint baked. In this work we also consider the effect of cold working and bake hardening on the fatigue life of the components.

Nano-scale analysis of nano-bainite formed in advanced high strength steels

The effect of composition and processing schedule on the microstructure of C-Mn-Si-Mo-(Al)-(Nb) steels containing nano-bainite was studied using transmission electron microscopy (TEM) and atom probe tomography (APT). The major phase formed in all steels was nano-bainite. However, the steels with lower carbon and alloying addition content subjected to TMP had better mechanical properties than high alloyed steel after isothermal treatment. The presence of ferrite in the microstructure can improve not only ductility but lead to the formation of retained austenite with optimum chemical stability.