Monitoring pitting-crevice corrosion using the WBE-noise signatures method

An electrochemically integrated multi-electrode array namely the wire beam electrode (WBE) and noise signatures analysis have been applied in novel combinations to study crevice corrosion behaviour in the presence of pits. Characteristic electrochemical noise signatures were found to correlate with characteristic changes in WBE current distribution maps, which indicate corrosion rates distributions, corrosion patterns and the degree of pitting and crevice corrosion. Specifically, two characteristic noise patterns were observed: (i) the characteristic noise pattern of quick potential changes towards more negative direction with no recovery (termed noise signature I) was found to correspond with the initiation and stabilization of the anode inside crevice; and (ii) the characteristic noise pattern of the cyclic potential oscillation at a constant frequency (termed noise signature II) was found to correspond with the stable anodic dissolution in the occluded cavity site in WBE current distribution maps. A new parameter namely the localization parameter (LP) has been proposed to describe the degree of localization. The LP for crevice corrosion was found to be low compared to that for pitting corrosion.

A novel crevice corrosion experiment using a wire beam electrode

This paper describes a new experiment for studying crevice corrosion. A wire beam electrode was employed in this experiment to measure electrochemical parameters directly from crevice area and these parameters were used to calculate instantaneous crevice corrosion kinetics. A clear correlation between calculated corrosion depth map and real corrosion appearance was obtained.

Studying non-uniform electrodeposition using the wire beam electrode method

Nonuniform electrodeposition is a major concern in almost every practical electrodeposition application. The ablility to control nonuniformity in electrodeposition is the key to successful plating for corrosion resistance, and more especially to meeting the very exacting requirements of electroforming, electrodeposition. This paper presents a novel technique namely the wire beam electrode (WBE) for characterizing and monitoring nonuniform electroplating processes. For the first time, the nonuniform distribution of electroplating currents (NDEC) has been mapped. Preliminary experimental results indicated that electrochemical heterogeneity was the key factor affecting NDEC. The secondary current distribution, rather than the primary current distribution, played a major role in determining the NDEC. This work suggests that the WBE is a practical tool for characterizing and optimizing electrodeposition processes and for verifying the accuracy and completeness of mathematic modelling of electrodeposition processes.

Oxygen reduction reaction activity of La-based perovskite oxides in alkaline medium : a thin-film rotating ring-disk electrode study

In this work, LaMO₃ and LaNi_0.5M_0.5O₃ (M = Ni, Co, Fe, Mn and Cr) perovskite oxide electrocatalysts were synthesized by a combined ethylenediaminetetraacetic acid-citrate complexation technique and subsequent calcinations at 1000 °C in air. Their powder X-ray diffraction patterns demonstrate the formation of a specific crystalline structure for each composition. The catalytic property of these materials toward the oxygen reduction reaction (ORR) was studied in alkaline potassium hydroxide solution using the rotating disk and rotating ring-disk electrode techniques. Carbon is considered to be a crucial additive component because its addition into perovskite oxide leads to optimized ORR current density. For LaMO₃ (M = Ni, Co, Fe, Mn and Cr)), in terms of the ORR current densities, the performance is enhanced in the order of LaCrO₃, LaFeO₃, LaNiO₃, LaMnO₃, and LaCoO3. For LaNi_0.5M_0.5O₃, the ORR current performance is enhanced in the order of LaNi_0.5Fe_0.5O₃, LaNi_0.5Co_0.5O₃, LaNi_0.5Cr_0.5O₃, and LaNi_0.5Mn_0.5O₃. Overall, LaCoO₃ demonstrates the best performance. Most notably, substituting half of the nickel with cobalt, iron, manganese, or chromium translates the ORR to a more positive onset potential, suggesting the beneficial catalytic effect of two transition metal cations with Mn as the most promising candidate. Koutecky–Levich analysis on the ORR current densities of all compositions indicates that the four-electron pathway is favored on these oxides, which are consistent with hydroperoxide ion formation of <2%.