Microstructure and mechanical properties of thermomechanically processed C-Si-Mn steels

Comparison of the microstructures formed in the specimens produced by corresponding schedules in the dilatometer and by laboratory rolling has shown that a higher level of retained austenite was achieved in dilatometer specimens, whereas in rolled specimens a higher amount of martensite was present instead of retained austenite.

Microstructure and mechanical properties of C-Si-Mn(-Nb) TRIP steels after simulated thermomechanical processing

Continuous and discontinuous cooling tests were performed using a quench deformation dilatometer to develop a comprehensive understanding of the structural and kinetic aspects of the bainite transformation in low carbon TRIP (transformation induced plasticity) steels as a function of thermomechanical processing and composition. Deformation in the unrecrystallised austenite region refined the ferrite grain size and increased the ferrite and bainite transformation temperatures for cooling rates from 10 to 90 K s^-1. The influence of niobium on the transformation kinetics was also investigated. Niobium increases the ferrite start transformation temperature, refines the ferrite microstructure, and stimulates the formation of acicular ferrite. The effect of the bainite isothermal transformation temperature on the final microstructure of steels with and without a small addition of niobium was studied. Niobium promotes the formation of stable retained austenite, which influences the mechanical properties of TRIP steels. The optimum mechanical properties were obtained after isothermal holding at 400°C in the niobium steel containing the maximum volume fraction of retained austenite with acicular ferrite as the predominant second phase.

A comparative study of microstructures and mechanical properties obtained by bar and plate rolling

Microstructures and mechanical properties of a low carbon steel were studied after plate rolling and bar rolling. Plate rolling is characterized as a monotonic compressive loading, while bar rolling is characterized as a cross-compressive loading. A four-pass plate rolling and bar rolling experiment was designed so that the material experiences the same amount of strain at each pass during rolling. The rolling experiment was performed at moderately high temperatures (450, 550 and 650 °C). The microstructures and mechanical properties of the low carbon steel acquired from the two types of rolling experiments were compared. The results revealed that differences of loading path attributed by monotonic loading (plate rolling) and cross loading (bar rolling) significantly influenced the microstructures and mechanical properties such as yield stress, ultimate tensile stress, strain hardening exponent and elongation of the low carbon steel.

Processing and mechanical properties of hollow sphere aluminum foams

Hollow sphere metallic foams are a new class of cellular material that possesses the attractive advantages of uniform cell size distribution and regular cell shape. These result in more predictable physical and mechanical properties than those of cellular materials with a random cell size distribution and irregular cell shapes. In the present study, single aluminum hollow spheres with three kinds of sphere wall thickness as 0.1 mm, 0.3 mm and 0.5 mm were processed by a new pressing method. Hollow sphere aluminum foam samples were prepared by bonding together single hollow spheres with simple cubic packing (SC) and body-centered cubic packing (BCC). Compressive tests were carried out to evaluate the deformation behaviors and mechanical properties of the hollow sphere aluminum foams. Effects of the sphere wall thickness and packing style on the mechanical properties were investigated.

A comparative study of the mechanical properties of wool and alpaca fibres

This study reports the latest research into alpaca and wool fibres. In particular, those properties that have received little attention in research literature have been examined. They include single fibre abrasion and bending fatigue, single fibre tensile properties, as well as resistance to compression behaviour. These properties are important because they affect the softness and pilling propensity of these fibres and the resultant fabrics. Clean wool and alpaca fibres were used in this study. Fibre abrasion/bending fatigue measurements were carried out using a Textechno FIBRESTRESS instrument. The resistance to compression (RtC) tests were carried out according to Australian Standard AS3535-1988. The results indicate that wool and alpaca fibres behave quite differently, even though both fibre types are of animal origin. Wool fibre resistance to compression decreases as fibre diameter increases while the opposite appears to occur for alpaca fibres. For both wool and alpaca the number of abrasion/bending cycles at fibre break increases with an increase in fibre diameter, it takes longer to break the alpaca fibres. Reasons for these differences have been postulated based on differences in fibre surface and structure between alpaca and wool.

Mechanical properties and bioactive surface modification via alkali-heat treatment of a porous ti-18Nb-4Sn alloy for biomedical applications

A porous Ti–18 at.%Nb–4 at.%Sn (hereafter, Ti–18Nb–4Sn) alloy was prepared by powder metallurgy. The porous structures were examined by scanning electron microscopy and the phase constituents were analysed by X-ray diffraction. Mechanical properties of the porous alloy were investigated using a compressive test. To enhance the bioactivity of the alloy surface, alkali-heat treatment was used to modify the surface. The bioactivity of the pre-treated alloy sample was investigated using a biomimetic process by soaking the sample into simulated body fluid (SBF). Results indicate that the elastic modulus and plateau stress of the porous Ti–18Nb–4Sn alloy decrease with decreasing relative density. The mechanical properties of the porous alloy can be tailored to match those of human bone. After soaking in SBF for 7 days, a hydroxyapatite layer formed on the surface of the pre-treated porous Ti–18Nb–4Sn alloy. The pre-treated porous Ti–18Nb–4Sn alloy therefore has the potential to be a bioactive implant material.

The dimensional and mechanical properties of wool/polyester fabrics made from vortex and ring-spun yarns

Fabric woven from wool/polyester (PES) Murata vortex spun (MVS) blend yarn is a commercially viable proposition particularly on the basis of advantageous wear-resistant properties, compared with fabric made from traditional worsted ring-spun yarn. However, in some early industrial trials with fabric made from 45/55-blend wool/PES MVS yarn, significantly greater relaxation shrinkage was found relative to comparable worsted ring-spun fabric. It was noted at the time that the amount of relaxation shrinkage in MVS fabric could be reduced to a large extent by using steamed MVS yarn.

In this study, the extent of variations in the dimensional and mechanical properties of fabric samples woven from a combination of steamed and unsteamed MVS yarn and equivalent worsted ring-spun yarn is examined. In general, greater hygral expansion and relaxation shrinkage were found in loom-state fabrics made from unsteamed MVS yarns, whereas the fabric made from steamed MVS and ring-spun yarns gave relatively low levels of relaxation shrinkage and hygral expansion. Permanent setting of fabrics, by pressure steaming, was found to be more effective than yarn pre-steaming in reducing relaxation shrinkage levels of fabrics made from unsteamed MVS yarn. After pressure steaming, all fabrics showed similar levels of relaxation shrinkage and hygral expansion.

Permanent setting of the fabrics, by pressure steaming, resulted in similar levels of relaxation shrinkage and hygral expansion, irrespective of the yarn production method; relaxation shrinkage fell to around 1% and hygral expansion increased by about 1%, relative to the loom-state samples. MVS fabrics were relatively heavier and fuller and had a firmer handle than the worsted ring-spun fabrics, reflecting the greater fabric weight, thickness and shear rigidity measured on these fabrics. These attributes are associated with different structures of the worsted ring-spun and MVS yarns used to make the fabrics.

Mechanical properties of titanium foam for biomedical applications

Understanding the mechanical behaviour of pure titanium (Ti) foam is crucial for the design and development of Ti foam-based load-bearing implants. In this work, pure titanium foam is fabricated by a powder metallurgical process using the space-holder technique with a spacer size of 500 to 800 µm. Experimental data from static compression testing on the Ti foam are presented. The application of theoretical formulae to predict Young's modulus and yield strength of titanium foams is also discussed. A foam with 63% porosity, 87 ± 5 MPa yield strength, and 6.5 ± 1.3 GPa Young's modulus is found to be appropriate for a number of dental and orthopaedic applications.

Mechanical properties of porous Ti-26NB alloy for regenerative medicine

Porous titanium-26at.%niobium (hereafter, Ti-26Nb) alloys with different porosities were prepared by space-holder sintering. The porous structure of the alloys was characterized by scanning electron microscopy (SEM). Mechanical properties of the porous alloys were investigated using compression test. Results indicate that the porous alloys with 60, 70 and 80% porosities exhibit interconnected porous structure with pore sizes of 100-300 µm. The porous structure has the potential to provide new bone tissue ingrowth ability. The mechanical properties of these porous alloys decrease with the increase of porosity. The mechanical properties of the porous Ti-26Nb alloys can be tailored to match those of human bone.

Processing and mechanical properties of porous Ti-Mo alloy for biomedical applications

Titanium and some of its alloys are well accepted as load-bearing implant materials due to their excellent mechanical properties, superior corrosion resistance, and outstanding biocompatibility. However, solid implant materials may suffer from the problems of adverse tissue reaction, biomechanical mismatch and lack of new bone tissue ingrowth ability. In the present study, porous titanium-molybdenum (Ti-Mo) alloy was fabricated by the space-holding sintering method. The pore size, pore shape and porosity can be controlled through choosing appropriate space-holding particle materials. Electron scanning microscopy (SEM) was used for the characterisation of the porous Ti-Mo alloy. The mechanical properties of the porous Ti-Mo alloy samples were investigated by compressive tests. Results indicated that the porous Ti-Mo alloy provides promising potential for new implant materials with new bone tissue ingrowth ability and mechanical properties mimicking those of natural bone.

Effects of process control agent on the microstructure and mechanical properties of Ti-Sn-Nb alloy prepared by mechanical alloying

In the present study, the influence of process control agent (PCA) on the characteristics of powder and bulk sintered Ti-16Sn-4Nb (wt. %) alloy prepared by mechanical alloying has been investigated. The elemental Ti, Sn and Nb powders were mechanically alloyed in a planetary ball mill for a short period of time using two types of PCA, namely stearic acid (SA) and ethylene bis-stearamide (EBS). The powder morphology, microstructural evolution of the bulk sintered alloy, phase formation and hardness of the alloy have been studied as a function of PCA. Results indicated that the addition of PCA leads to a delay in aIloy formation and introduces contaminations (mainly carbon and oxygen) into the material. The microstructural observation of the bulk alloy revealed a homogeneous distribution of fine Nb-rich colonies (ß-phase) within the a-Ti matrix for small amount of PCA. The hardness values of samples exhibited a significant increase with increasing amount of PCA, reaching a value of ~ 600 BV.