Collagen type-I leads to in vivo matrix mineralization and secondary stabilization of Mg-Zr-Ca alloy implants

Biodegradable magnesium-zirconia-calcium (Mg-Zr-Ca) alloy implants were coated with Collagen type-I (Coll-I) and assessed for their rate and efficacy of bone mineralization and implant stabilization. The phases, microstructure and mechanical properties of these alloys were analyzed using X-ray diffraction (XRD), optical microscopy and compression test, respectively, and the corrosion behavior was established by their hydrogen production rate in simulated body fluid (SBF). Coll-I extracted from rat tail, and characterized using fourier transform infrared (FT-IR) spectroscopy, was used for dip-coating the Mg-based alloys. The coated alloys were implanted into the femur bones of male New Zealand white rabbits. In vivo bone formation around the implants was quantified by measuring the bone mineral content/density (BMC/BMD) using dual-energy X-ray absorptiometry (DXA). Osseointegration of the implant and new bone mineralization was visualized by histological and immunohistochemical analysis. Upon surface coating with Coll-I, these alloys demonstrated high surface energy showing enhanced performance as an implant material that is suitable for rapid and efficient new bone tissue induction with optimal mineral content and cellular properties. The results demonstrate that Coll-I coated Mg-Zr-Ca alloys have a tendency to form superior trabecular bone structure with better osteoinduction around the implants and higher implant secondary stabilization, through the phenomenon of contact osteogenesis, compared to the control and uncoated ones in shorter periods of implantation. Hence, Coll-I surface coating of Mg-Zr-Ca alloys is a promising method for expediting new bone formation in vivo and enhancing osseointegration in load bearing implant applications.

Optimization of milling parameters on the synthesis of stearic acid coated CaCO3 nanoparticles

Surface modification of precipitated calcium carbonate particles (calcite) in a planetary ball mill using stearic acid as a modification agent for making dispersion in hydrocarbon oil was investigated. Different parameters for processing (milling) such as milling time, ball-to-sample ratio, and molar ratio of the reactant were varied and analyzed for optimization. The physical properties of the hydrophobically modified calcium carbonate particles were measured; the particle size and morphology of the resulting samples were characterized by transmission electron microscopy and X-ray diffraction. The surface coating thickness was estimated using small angle X-ray scattering. © 2014 American Coatings Association & Oil and Colour Chemists' Association.

Photochromic fabrics with improved durability and photochromic performance

Previously, we have reported a method for producing photochromic wool fabric by applying a thin layer of hybrid silica-photochromic dye onto the wool surface. While the photochromic coating showed a very fast optical response and had little influence on the fabric handle, its durability was poor. In this study, the durability of the photochromic coating layer was improved by introducing epoxy groups into the silica matrix via co-hydrolysis and co-condensation of an alkyl trialkoxysilane compound (ATAS) and 3-glycidoxypropyltrimethoxysilane (GPTMS). The presence of epoxy groups in the silica enhanced both washing and abrasion durability or fastness. In addition, the optical response speed was slightly increased as well. Effects of the type of alkyl silane and the GPTMS/alkyl silane ratio on the coating durability, fabric handle and optical response were examined.

Electrical conductivity of single walled and multiwalled carbon nanotube containing wool fibers

The main purpose of this study was producing conductive wool fabric applying carbon nanotubes. Raw and oxidized wool samples were treated with carbon nanotubes in the impregnating bath in the presence of citric acid as a crosslinking agent and sodium hypophosphite as a catalyst while sonicating them in the ultrasonic bath. Electrical resistance, washing durability, and color variation of treated samples were assessed. Through SEM images, the surface morphology of treated samples was studied confirming the surface coating through carbon nanotubes. According to the results, the electrical resistance of treated wool with carbon nanotubes reduced substantially. However, the single-walled carbon nanotubes are more useful to increase the conductivity. In addition, the wool color changed into gray after the treatment.

One-step coating of fluoro-containing silica nanoparticles for universal generation of surface superhydrophobicity

Stable superhydrophobic surfaces with water contact angles over 170 degrees and sliding angles below 7 degrees were produced by simply coating a particulate silica sol solution of co-hydrolysed TEOS/fluorinated alkyl silane with NH₃^.H₂O on various substrates, including textile fabrics (e.g. polyester, wool and cotton), electrospun nanofibre mats, filter papers, glass slides, and silicon wafers.

Biomimetic coating on pure titanium submitted to different surface treatments

Titanium (Ti) plates were firstly treated to form various types of oxide layers on the surface and then immersed into simulated body fluid (SBF) to evaluate the apatite forming ability. The surface morphology and roughness of the different oxide layers were measured by atomic force microscopy (AFM), and the surface energies were determined based on the Owens-Wendt (OW) methods. It was found that Ti samples after Alkali-Heat treatment (AH) achieved the best apatite formation after soaking in SBF for 3 weeks, compared to those without treatment, thermal or H₂O₂ oxidation. Furthermore, contact angle measurement revealed that the oxide layer on the alkali-heat treated Ti samples possessed the highest surface energy. The results indicate that the apatite inducing ability of a titanium oxide layer is linked to its surface energy. Apatite nucleation is easier on a surface with a higher surface energy.

Fluidized bed CrN coating formation on prenitrocarburized plain carbon steel

CrN coatings were formed on plain carbon steel by prenitrocarburizing, followed by thermoreactive deposition and diffusion (TRD) in a fluidized bed furnace at 570 °C. During TRD, Cr was transferred from Cr powder in the fluidized bed to the nitrocarburized substrates by gas-phase reactions initiated by reaction of HCl gas with the Cr. The microstructural processes occurring in the white layer, caused by N diffusion toward the surface during this stage were studied. This study compares TRD atmospheres employing inert gas and HCl or inert gas, H2, and HCl. Surface characterization was performed by scanning electron microscopy (SEM), x-ray diffraction (XRD), and glow-discharge optical-emission spectroscopy (GDOES).

Cr(N,C) diffusion coating formation on pre-nitrocarburised H13 tool steel

The microstructural processes of Cr(N,C) coating formation by thermoreactive deposition and diffusion (TRD) on pre-nitrocarburised H13 tool steel were studied. Both nitrocarburising and TRD were performed in fluidized bed furnaces at 570 °C. During TRD, chromium was transferred from chromium powder in the fluidized bed, to the nitrocarburised substrates by gas-phase reactions initiated by reaction of HCl gas with the chromium. Addition of 30% H2 to the input inert gas was found to increase the rate of coating formation, although hydrogen reduction resulted in rapid loss of nitrogen to the surface. The reason for the increased rate of coating formation could not be established without further investigation, although several possible explanations have been proposed. It was found that porosity and the formation of an iron nitride ‘cover layer’ during nitrocarburising were the biggest influences on the microstructure of the Cr(N,C) coating. Microstructural characterization of the coatings was performed by scanning electron microscopy (SEM), X-ray diffraction (XRD) and glow discharge optical emission spectroscopy (GDOES).

Interaction between the coating characteristics of galvanneal steel and forming parameters during flat die drawing

Galvanneal steel is considered to be better for automotive applications than its counterpart, galvanized steel, mainly because of its superior coating and surface properties. Galvanneal steel is produced by hot dipping sheet steel in a bath of molten zinc with small, controlled, levels of aluminium, followed by annealing which creates a Fe-Zn intermetallic layer. This intermetallic layer of the coating improves spot weldability and improves subsequent paint appearance. However, if the microstructure of the coating is not properly controlled and forming parameters are not properly selected, wear of the coating could occur during stamping. Frictional sliding of the sheet between the tool surfaces results in considerable amount of coating loss. An Interstitial Free steel with a Galvanneal coating of nominally 60g/m2 was used for the laboratory experiments. Flat Face Friction (FFF) tests were performed with different forming conditions and lubricants to simulate the frictional sliding in stamping. Glow-Discharge Optical Emission Spectrometry (DG-OES) was used to measure the change in the coating thickness during sliding. Optical microscopy was considered for imaging the surfaces as well as an optical method to compare the changes in the coating thickness during the forming. The change to the Galvanneal coating thickness was found to be a function of forming parameters.

Synthesis, polymerization and wool coating studies of 3-iso-butylpyrrole and 3-iso-pentylpyrrole

In a four-step method starting from pyrrole, the synthesis of 3-iso-butylpyrrole and 3-iso-pentylpyrrole, was achieved in 45 and 44% yields, respectively. Polymerization studies of these branched alkyl pyrroles are described and the results compared with those obtained for the unbranched structural isomers n-butyl and n-pentylpyrrole. A series of conductive textiles were produced by the chemical polymerization of the iso-alkylpyrroles using both solution and vapour polymerization techniques. Fabrics coated with poly-iso-alkylpyrrole formed using the solution polymerization method had a lower surface resistance than those formed using the vapour polymerization method. These conductivity results were in direct contrast to those previously obtained for 3-n-alkylpyrroles on fabrics. A remarkable crystal-like growth on the surface of the textile fabric was observed when solution polymerization of 3-iso-pentylpyrrole was employed—reinforcing the notion that subtle changes in monomer structure can drastically affect bulk polymer properties.

Polymerising pyrrole on polyester textiles and controlling the conductivity through coating thickness

The surface resistance of polypyrrole (PPy)-coated polyester fabrics was investigated and related to coating thickness, which was controlled by adjusting the reactant concentrations. The thickness of the coating initially increased rapidly followed by a steady increase when the concentration of pyrrole (Py) was larger than a concentration of approximately 0.4 mg/ml. The surface resistance decreased from 10⁶ to 10³ Ω with increase in pyrrole concentration within 0.2 mg/ml until the concentration reached a value of about 0.4 mg/ml, above which the rate of decrease diminished. The effect of initial treatment with monomer or oxidant prior to polymerisation reaction with regards to thickness and surface resistance was minimal. The immersion time of the textile into the monomer solution prior to polymerisation reaction did not have a significant effect on the abrasion resistance.

Improvement of adhesion of conductive polypyrrole coating on wool and polyester fabrics using atmospheric plasma treatment

In this paper wool and polyester fabrics were pretreated with atmospheric plasma glow discharge (APGD) to improve the ability of the substrate to bond with anthraquinone-2-sulfonic acid doped conducting polypyrrole coating. A range of APGD gas mixtures and treatment times were investigated. APGD treated fabrics were tested for surface contact angle, wettability and surface energy change. Effect of the plasma treatment on the binding strength was analyzed by studying abrasion resistance, surface resistivity and reflectance. Investigations showed that treated fabrics exhibited better hydrophilicity and increased surface energy. Surface treatment by an APGD gas mixture of 95% helium/5% nitrogen yielded the best results with respect to coating uniformity, abrasion resistance and conductivity.

Effect of surface roughness of Ti, Zr, and TiZr on apatite precipitation from simulated body fluid

Some of the critical properties for a successful orthopedic or dental implant material are its biocompatibility and bioactivity. Pure titanium (Ti) and zirconium (Zr) are widely accepted as biocompatible metals, due to their non-toxicity. While the bioactivity of Ti and some Ti alloys has been extensively investigated, there is still insufficient data for Zr and titanium-zirconium (TiZr) alloys. In the present study, the bioactivity, that is, the apatite forming ability on the alkali and heat treated surfaces of Ti, Zr, and TiZr alloy in simulated body fluid (SBF), was studied. In particular, the effect of the surface roughness characteristics on the bioactivity was evaluated for the first time. The results indicate that the pretreated Ti, Zr and TiZr alloy could form apatite coating on their surfaces. It should be noted that the surface roughness also critically affected the bioactivity of these pretreated metallic samples. A surface morphology with an average roughness of approximately 0.6 microm led to the fastest apatite formation on the metal surfaces. This apatite layer on the metal surface is expected to bond to the surrounding bones directly after implantation.

Biomimetic processing of nanocrystallite bioactive apatite coating on titanium-zirconium alloy

In this paper nanocrystallite apatite coating on TiZr substrate was prepared by a biomimetic process. Surface morphology, thickness, crystalline phases a~nd bond strength of the coating were investigated by SEM, XRD and tensIle test, respectively. Results show that the apatite coating exhibIts a nanocrystalIite structure with similar stoichiometry to that of natural bone. The apatite layer becomes thicker with the increasing of the SBF immersion time and is firmly adhered to the substrate with the highest average bond strength of 15.5 MPa. This nanocrystallite apatite coating is expected to bond to surrounding bone tissue directly in vivo after implantation.