Silicone coated metal oxide particles

A process for applying a silicone coating to metal oxide particles is described. The process comprises the steps of: preparing a mixture of an aqueous suspension of metal oxide particles and an aqueous solution of water-soluble organosilicon monomers; and, adding a pH-lowering agent to the mixture so as to initiate polymerisation of the water-soluble organosilicon monomers and form silicone coated metal oxide particles. The process does not require the use of an organic solvent.

Polymer-in-ionic-liquid electrolytes

In order to achieve high conductivity in a polymer electrolyte, polymer-in-ionic-liquid electrolytes have been explored. It is found in this study that poly[vinylpyrrolidone-co-(vinyl acetate)] (P(VP-c-VA)) in 1-ethyl-3-methylimidazolium bis(trifluoromethyl sulfonyl) amide (EtMeIm+Tf2N−) and poly(N,N-dimethyl acrylamide) (PDMAA) in trimethyl butyl ammonium bis(trifluoromethane sulfonyl) amide (N1114+Tf2N−) produce ion-conducting liquids and gels. The P(VP-c-VA)/ EtMeIm+Tf2N− mixture has a conductivity around 10−3 S · cm−1 at 22 °C, for copolymer concentrations up to 30 wt.-%. Thermal analysis shows that the Tg of the P(VP-c-VA)/ EtMeIm+Tf2N− system is well described by the Fox equation as a function of polymer content. Poly(methyl methacrylate) (PMMA)/ EtMeIm+Tf2N− gel electrolytes were prepared by in-situ polymerisation of the monomer in the ionic liquid. In the presence of 0.5–2.0 wt.-% of a crosslinking agent, these PMMA-based electrolytes displayed elastomeric properties and high conductivity (ca. 10−3 S · cm−1) at room temperature.

Order–disorder transitions in poly(3,4-ethylenedioxythiophene)

The commonly held perception that high conductivity in conducting polymers is linked to a high level of π-stacking order in the material is shown here to be of lesser importance in highly conducting poly(3,4-ethylenedioxythiophene) (PEDT), which has been prepared by chemical vapour phase polymerisation. Despite the fact that there is a highly energetic phase transition about 130 °C (110 J/g), and that this transition corresponds to a loss of the long-range π-stacking as observed in grazing angle XRD, the conductivity remains unchanged beyond the transition and only decreases by a factor of two when heating to above 200 °C. The XRD data suggest that order in two dimension remains above the phase transition measured by DSC and this order is sufficient to maintain a high level of electronic conductivity. Furthermore, as the ligand on the iron salt used in the synthesis is varied, the conductivity of the PEDT varies over two orders of magnitude. These phenomena cannot be explained by different degree of doping or crystallinity and it is proposed that the iron salt has an ordering effect during the vapour phase polymerisation.

High current density and drift velocity in templated conducting polymers

Conducting polymers prepared by a templated vapour phase polymerisation process involving solid phase transition metal complexes are found to produce polymers with charge carriers that exhibit maximum drift velocity in the range of 1 m/s. This super-mobility seems to be related to a high degree of ordering in the materials as evidenced by the X-ray diffraction data. This may result from a templated polymerisation process. The high mobility manifests itself as a capacity to sustain very high current densities (>10000 A/cm2); such high current densities are of importance in thin film conductor applications.

An investigation of polypyrrole coated conductive textiles: this research aimed at clarifying some issues occurred in the research project on coloured conductive textiles

Coloured conducting textiles have shown a wide range of potential applications in heating fabrics, electromagnetic wave absorption, and wearable optoelectronic devices. This research aimed at clarifying some issues occurred in the research project on coloured conductive textiles. The investigation firstly clarified a possible chemical reaction that took place between a commercial dispersing dye (Terasil Red G) and the conducting polymer polypyrrole, through chemical separation, structural identification and spectrum characterisations. Then, a series of acidic dyes were introduced into polypyrrole matrix during the vapour coating of conducting polymer on the wool fabrics. Colour and thermal stability studies were conducted. Finally, the polypyrrole nanoparticles (particle size several~200nm) were prepared by a microemulsion polymerisation technique. An acid dye was used as the dopant to re-dope the nanoparticles. The effect of the acidic dye on the optical absorption of nanoparticles was studied. Applying the conducting nanoparticles on wool fabrics may open an alternative path to achieve the coloured conducting textiles.

Polyterthiophene/CNT composite as a cathode material for lithium batteries employing an ionic liquid electrolyte

A polyterthiophene (PTTh)/multi-walled carbon nanotube (CNT) composite was synthesised by in situ chemical polymerisation and used as an active cathode material in lithium cells assembled with an ionic liquid (IL) or conventional liquid electrolyte, LiBF₄/EC–DMC–DEC. The IL electrolyte consisted of 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIBF₄) containing LiBF₄ and a small amount of vinylene carbonate (VC). The lithium cells were characterised by cyclic voltammetry (CV) and galvanostatic charge/discharge cycling. The specific capacity of the cells with IL and conventional liquid electrolytes after the 1st cycle was 50 and 47 mAh g⁻¹ (based on PTTh weight), respectively at the C/5 rate. The capacity retention after the 100th cycle was 78% and 53%, respectively. The lithium cell assembled with a PTTh/CNT composite cathode and a non-flammable IL electrolyte exhibited a mean discharge voltage of 3.8 V vs Li⁺/Li and is a promising candidate for high-voltage power sources with enhanced safety.

Colloid probe AFM study of thermal collapse and protein interactions of poly(N-isopropylacrylamide) coatings

Graft coatings of poly(N-isopropylacrylamide) (pNIPAM) are of considerable interest for the reversible control of bio-interfacial interactions. In this study, graft coatings were prepared by free radical polymerisation from surface-bound polymerisable groups, on silicon wafers and quartz crystal microbalance (QCM) sensors. QCM with dissipation monitoring showed a gradual, extended phase change as the temperature increased. Colloid probe atomic force microscopy (CP-AFM) revealed a marked change in the compressibility of the coating below and above the lower critical solution temperature (LCST). Force curves showed an approximate 9-fold reduction in thickness between 24 °C and 38 °C, yet the collapsed coating at 38 °C still had a thickness significantly higher than the ellipsometrically determined dry thickness, indicating a residual extent of hydration above the LCST. At all temperatures, interaction force curves showed steric repulsion, though over different distances. There was little hysteresis between approach and retract force curves, which is evidence for almost instantaneous relaxation of the coating upon decompression. CP-AFM using a probe coated with bovine serum albumin (BSA) showed repulsive interactions with little approach/retraction hysteresis below the LCST, indicating lack of adhesion between the pNIPAM coating and the BSA-coated probe. In contrast, above the LCST the force curves on retraction were characteristic of adhesion, while the approach curves were still repulsive, and the adhesion increased in strength as the temperature was increased further beyond the LCST. Thus, QCM-D and CP-AFM data correlated well in showing a gradual nature of the phase transition and a concomitant gradual change in the interaction force with BSA.

One-step vapour-phase formation of patternable, electrically conductive, superamphiphobic coatings on fibrous materials

Patternable, electrically conductive coatings having a superhydrophobic and superoleophobic surface have been prepared by one-step vapour-phase polymerisation of polypyrrole in the presence of a fluorinated alkyl silane directly on fibrous substrates. The coated fabrics showed a surface resistance of 0.5-0.8 kΩ □^-1 with water and hexadecane contact angles of 165° and 154°, respectively.

The effect of a rapid heating rate, mechanical vibration and surfactant chemistry on the structure-property relationships of epoxy/clay nanocomposites

The role of processing conditions and intercalant chemistry in montmorillonite clays on the dispersion, morphology and mechanical properties of two epoxy/clay nanocomposite systems was investigated in this paper. This work highlights the importance of employing complementary techniques (X-ray diffraction, small angle X-ray scattering, optical microscopy and transmission electron microscopy) to correlate nanomorphology to macroscale properties. Materials were prepared using an out of autoclave manufacturing process equipped to generate rapid heating rates and mechanical vibration. The results suggested that the quaternary ammonium surfactant on C30B clay reacted with the epoxy during cure, while the primary ammonium surfactant (I.30E) catalysed the polymerisation reaction. These effects led to important differences in nanocomposite clay morphologies. The use of mechanical vibration at 4 Hz prior to matrix gelation was found to facilitate clay dispersion and to reduce the area fraction of I.30E clay agglomerates in addition to increasing flexural strength by over 40%.

Change in dielectric properties in the microwave frequency region of polypyrrole-coated textiles during aging

Complex permittivity of conducting polypyrrole (PPy)-coated Nylon-Lycra textiles ismeasured using a free space transmission measurement technique over the frequency range of1–18 GHz. The aging of microwave dielectric properties and reflection, transmission and absorptionfor a period of 18 months is demonstrated. PPy-coated fabrics are shown to be lossy over thefull frequency range. The levels of absorption are shown to be higher than reflection in the testedsamples. This is attributed to the relatively high resistivity of the PPy-coated fabrics. Both the dopantconcentration and polymerisation time affect the total shielding effectiveness and microwave agingbehaviour. Distinguishing either of these two factors as being exclusively the dominant mechanismof shielding effectiveness is shown to be difficult. It is observed that the PPy-coated Nylon-Lycrasamples with a p-toluene sulfonic acid (pTSA) concentration of 0.015 M and polymerisation times of60 min and 180 min have 37% and 26% decrease in total transmission loss, respectively, upon agingfor 72 weeks at room temperature (20 C, 65% Relative humidity (RH)). The concentration of thedopant also influences the microwave aging behaviour of the PPy-coated fabrics. The samples with ahigher dopant concentration of 0.027 mol/L pTSA are shown to have a transmission loss of 32.6% and16.5% for short and long polymerisation times, respectively, when aged for 72 weeks. The microwaveproperties exhibit better stability with high dopant concentration and/or longer polymerization times.High pTSA dopant concentrations and/or longer polymerisation times result in high microwaveinsertion loss and are more effective in reducing the transmission and also increasing the longevity ofthe electrical properties.