Effect of composition and austenite deformation on the transformation characteristics of low-carbon and ultralow-carbon microalloyed steels

Deformation dilatometry has been used to simulate controlled hot rolling followed by controlled cooling of a group of low- and ultralow-carbon microalloyed steels containing additions of boron and/or molybdenum to enhance hardenability. Each alloy was subjected to simulated recrystallization and nonrecrystallization rolling schedules, followed by controlled cooling at rates from 0.1 °C/s to about 100 °C/s, and the corresponding continuous-cooling-transformation (CCT) diagrams were constructed. The resultant microstructures ranged from polygonal ferrite (PF) for combinations of slow cooling rates and low alloying element contents, through to bainitic ferrite accompanied by martensite for fast cooling rates and high concentrations of alloying elements. Combined additions of boron and molybdenum were found to be most effective in increasing steel hardenability, while boron was significantly more effective than molybdenum as a single addition, especially at the ultralow carbon content. Severe plastic deformation of the parent austenite (>0.45) markedly enhanced PF formation in those steels in which this microstructural constituent was formed, indicating a significant effective decrease in their hardenability. In contrast, in those steels in which only nonequilibrium ferrite microstructures were formed, the decreases in hardenability were relatively small, reflecting the lack of sensitivity to strain in the austenite of those microstructural constituents forming in the absence of PF.

Warm deformation and annealing behaviour of iron-silicon-(carbon) steel sheets

Single pass warm rolling and compression experiments were carried out from ambient to 800°C for ultra-low carbon (ULC) steel with ∼100 ppm carbon and interstitial free (IF) steels, both with two levels of silicon. Subsequently, annealing was done in order to recrystallize the deformed specimens. The main purpose of this study was to understand the effects of rolling temperature and silicon on stress responses and textures. This study comprises two main themes: flow stress and strain rate sensitivity during compression and shear banding and textures in warm rolled specimens. The effects of deformation temperature on in-grain shear bands were different between ULC-Si and IF-Si steels. As in previous work with more conventional steels, in-grain shear bands in the IF grade had low sensitivity to rolling temperature, while those in the ULC grade depended significantly on the deformation temperature. However, the temperature profile of shear banding in the ULC grade was approximately 150°C higher than in previous work. Deformation and recrystallisation textures for both IF and ULC grades depended on their rolling temperatures. The variation of both grain size and texture after annealing can be explained by the rise and fall of in-grain shear banding activity which is related to the strain rate sensitivity.

The formation of ultrafine ferrite through static transformation in low carbon steels

A novel approach was used to produce an ultrafine grain structure in low carbon steels with a wide range of hardenability. This included warm deformation of supercooled austenite followed by reheating in the austenite region and cooling (RHA). The ultrafine ferrite structure was independent of steel composition. However, the mechanism of ferrite refinement changed with the steel quench hardenability. In a relatively low hardenable steel, the ultrafine structure was produced through dynamic strain induced transformation, whereas the ferrite refinement was formed by static transformation in steels with high quench hardenability. The use of a model Ni-30Fe austenitic alloy revealed that the deformation temperature has a strong effect on the nature of the intragranular defects. There was a transition temperature below which the cell dislocation structure changed to laminar microbands. It appears that the extreme refinement of ferrite is due to the formation of extensive high angle intragranular defects at these low deformation temperature that then act as sites for static transformation. © 2008 World Scientific Publishing Company.

Combined atom probe tomography and density functional theory investigation of the Al off-stoichiometry of κ-carbides in an austenitic Fe-Mn-Al-C low density steel

We report on the investigation of the off-stoichiometry and site-occupancy of κ-carbide precipitates within an austenitic (γ), Fe-29.8Mn-7.7Al-1.3C (wt.%) alloy using a combination of atom probe tomography and density functional theory. The chemical composition of the κ-carbides as measured by atom probe tomography indicates depletion of both interstitial C and substitutional Al, in comparison to the ideal stoichiometric L′12 bulk perovskite. In this work we demonstrate that both these effects are coupled. The off-stoichiometric concentration of Al can, to a certain extent, be explained by strain caused by the κ/γ mismatch, which facilitates occupation of Al sites in κ-carbide by Mn atoms (MnγAl anti-site defects). The large anti-site concentrations observed by our experiments, however, can only be stabilized if there are C vacancies in the vicinity of the anti-site.

Ultrafine grained ferrite formed by interrupted hot torsion deformation of plain carbon steel

A plain carbon steel was deformed using a hot torsion deformation simulator. A schedule known to produce strain-induced ferrite was used with the strain interrupted for increasing intervals of time to determine the effect of an isothermal hold on the final microstructure. Microscopy and electron back-scattered diffraction (EBSD) were used to analyse the changes that occurred in the partially transformed microstructure during the hold and the subsequent applied strain. The strain-induced ferrite coarsened during the hold and this coarsened ferrite was refined during the second deformation. These results were compared to those obtained for a different plain carbon steel deformed in single pass rolling close to the Ar3 temperature.

Fluidized bed CrN coating formation on prenitrocarburized plain carbon steel

CrN coatings were formed on plain carbon steel by prenitrocarburizing, followed by thermoreactive deposition and diffusion (TRD) in a fluidized bed furnace at 570 °C. During TRD, Cr was transferred from Cr powder in the fluidized bed to the nitrocarburized substrates by gas-phase reactions initiated by reaction of HCl gas with the Cr. The microstructural processes occurring in the white layer, caused by N diffusion toward the surface during this stage were studied. This study compares TRD atmospheres employing inert gas and HCl or inert gas, H2, and HCl. Surface characterization was performed by scanning electron microscopy (SEM), x-ray diffraction (XRD), and glow-discharge optical-emission spectroscopy (GDOES).

The static, dynamic and metadynamic recrystallisation of a medium carbon steel

Grain refinement during and after hot isothermal deformation of a medium carbon steel has been investigated. The average austenite grain size decreased with an increase in strain for the hot deformed and recrystallised material, with refinement extending beyond the strain for the peak stress. A window of strain that corresponds to transition from classical static to metadynamic recrystallisation was observed in respect to the recrystallised material. Within this post-dynamic transition window the strain at which strain independent softening occurs was different for different volume fractions of the recrystallised material. This led to a new terminology corresponding to initiation of strain independent softening. For the alloy of this study, strain independent softening for the start of post-deformation recrystallisation occurred near the strain to the peak stress. The strain corresponding to complete metadynamic recrystallisation, which was defined as when all levels of recrystallisation were strain independent, was much greater than the strain for the peak stress.

Low strain processing of LC and ULC steels

Temper rolling and tension levelling are commonly used to manufacture flat rolled steel. Both processes lengthen the steel at strains up to 3% by applying a load and stretching the strip. By latering the balance between the load and the tension the formability of the low carbon and ultra low carbon steel may be optimised.

Transition to a low carbon footprint : a conceptual model of impacts and management for Australian businesses

Australian businesses will face profound and wide-ranging structural impacts during their transition to a low carbon footprint economy. This paper synthesizes the impacts for the firm during the transition and identifies the crucial impact variables. In doing so, it explores the link between the opportunities and benefits, costs, risks and structural changes and evaluates the challenges in managing the multiple impacts. The paper provides a conceptual model that will assist decision-makers deal with risk management or bottom-line protection issues as well as exploiting the business opportunity the new regulatory environment will produce. The model argues for a holistic corporate governance mechanism, with responsibility and accountability of climate change risk management placed with the board of directors and senior management. The literature review is presented first, followed by the discussion and the model. Future empirical research direction is also presented with the development of a series of propositions for testing.

Regulatory challenges in the move to a low-carbon environment

An outcome of the international climate conference in Copenhagen (COP 15, 2009) was that a number of governments have undertaken to reduce their nations' greenhouse gas (GHG) emissions and some have provided targets and deadlines for the achievement of their stated goals. While the transition to a low-carbon environment has the potential to stimulate growth, create jobs and opportunities, and to bring benefits to the economy, there are many challenges in the process. This is an exploratory paper aimed at identifying the major regulatory and governance issues associated with the move to a low-carbon environment. In terms of business governance, CEOs and other executives responsible for corporate oversight will need to monitor, assess, and manage compliance with climate change and carbon-related regulation. In the transition period government regulation encouraging appropriate carbon costs classification and measurement, financial sustainability reporting and disclosure, and responsible carbon citizenship are expected to be predominant.