Synthesis of ZnO nanowires using ball-milling and annealing method

Nanowires represent a new class of ZnO morphologies with many exiting new properties and applications. The research in the synthesis and characterization of ZnO nanowires has received enormous attention in recent years. However, most synthesis methods using vapor deposition process can only produce small amount of sample, mass production has not been achieved yet. Large-quantity production of ZnO nanowires needs to be realized for large-scale property and application studies. One of the promising approaches to the large scale synthesis is a ball-milling and annealing method. This paper first introduces several common synthesis methods of ZnO nanowires and then summarizes the one dimensional nanomaterials produced by the ball milling and annealing method. Finally, some preliminary results of ZnO nanowire synthesis are presented.

Conical boron nitride nanorods synthesized via the ball-milling and annealing method

A boron nitride (BN) nanostructure, conical BN nanorod, has been synthesized in a large quantity on Si substrates for the first time via the ball-milling and annealing method. Nitridation of milled boron carbide (B₄C) powders was performed in nitrogen gas at 1300°C on the surface of the substrates to form the BN nanorods. The highly crystallized nanorods consist of conical BN basal layers stacked along the nanorod axis. Ball milling of the B₄C powders can significantly enhance the nitridation of the powders and thus facilitate the formation of nanorods during the annealing process.

Efficient production of ZnO nanowires by a ball milling and annealing method

ZnO powder was mechanically milled in a ball mill. This procedure was found to greatly increase its evaporation ability. The anomalous evaporation behaviour was caused by the disordered structure of the milled material and was not related to the increase in its surface area after milling. ZnO nanowires were synthesized by evaporation of this milled precursor. Nanowires with smooth and rough surfaces were present in the sample; the latter morphology was dominant. A green emission band centred at 510 nm was dominant in the cathodoluminescence spectrum of the nanowires.

One-dimensional nanomaterials synthesized using high-energy ball milling and annealing process

One-dimensional (1D) nanomaterials including nanotubes, nanowires and nanorods have many new properties, functionalities and a large range of promising applications. A major challenge for these future industrial applications is the large-quantity production. We report that the ball milling and annealing process has the potential to achieve the mass production. Several examples including C, BN nanotubes and SiC, Zn nanowires are presented to demonstrate such capability. In addition, both size and structure of 1D nanomaterials can be controlled by varying processing conditions. New growth mechanisms involved in the process have been investigated and the high-energy ball milling has an important role in the formation of these 1D nanomaterials.

‘Be yourself and have a ball’ : using a school and community based health education model to build young women’s resilience and connectedness

Recognition of the important role schools play in the promotion of student wellbeing can be seen in the growing number of polices and programs being implemented in schools across the Australia. This paper reports on some initial data from focus group interviews with year 9 and 10 girls involved in the pilot of a health and physical activity intervention designed to connect them to their local community and reconnect them with their school and their peers. The aim of the program was to build connectedness and resilience by engaging young women in non-traditional physical activities whilst providing them with a sound understanding of health issues relevant to adolescent girls. Situated in a relatively isolated rural community 200 kilometers south east of Melbourne the program was overwhelmingly delivered by regional and local agencies in conjunction with the local secondary school. The intervention was built on a partnerships model designed with the purpose of increasing participation and access for young women whilst building a sustainable program run in partnership between the school and local agencies and services. The initial data from this pilot indicates the program is having a positive impact on the young women’s sense of self and their bodies, their relationships with their peers and in reducing bullying behaviour amongst the girls. However the data raises some important questions around the adequacy of school-based health education, and the sustainability of approaches designed to be delivered by outside agencies rather than classroom teachers.

Older people playing ball : what is the risk of falling and injury?

Increasing physical activity amongst seniors is important for public health, yet guidance is needed to minimise injury risks. To describe the incidence of falls/injuries in a walking team ball game (Lifeball) designed for seniors, a prospective cohort study was undertaken amongst community dwelling Lifeball participants in Australia. Players completed a telephone survey soon after commencing Lifeball (2004) and 12 months later (2005). Attendance and incident records were audited for the period. Subjects joined a Lifeball group with opportunity to play at least once per week. Baseline was completed by 284 players aged between 40 and 96 years (mean 67 years), with most (83.8%, 238/284) female. Of 263 followed up, the average attendances was 25, with 19.3% attending on fewer than 4 occasions and 14.3% attending 52 or more times. Most (93.9%) reported no injuries requiring medical attention. However, 16 (6.1%) had injuries requiring medical attention and their 27 injuries represent an injury rate of 3.3 per 1000 hours of participation. Twenty participants (7.6%) had a Lifeball fall equating to a fall rate of 2.8 per 1000 hours of participation. Falls in Lifeball were not associated with measured predictors (age, gender, falls history, perceived falls risk or hours played). Incident records showed a trip/stumble involving rushing, walking backwards, or overextending (all against rules) as common falling causes. Lifeball is not ‘risk free’ however due to a lack of comparative data it is difficult to compare injury rate to relevant activities. Prevention of injury should concentrate on enforcing safety rules.

Utilising solar energy within conventional coal fired power stations

Although the thermodynamic advantages of using solar energy to replace the bled off steam in the regeneration system of Rankine cycle coal fired power stations has been proven theoretically, the practical techno/economic feasibility of the concept has yet to be confirmed relative to real power station applications. To investigate this concept further, computer modelling software “THERMSOLV” was specifically developed for this project at Deakin University, together with the support of the Victorian power industry and Australian Research Council (ARC). This newly developed software simulates the steam cycle to assess the techno/economic merit of the solar aided concept for various power station structures, locations and local electricity market conditions. Two case studies, one in Victoria Australia and one in Yunnan Province, China, have been carried out with the software. Chapter one of this thesis defines the aims and scope of this study. Chapter two details the literature search in the related areas for this study. The thermodynamic concept of solar aid power generation technology has been described in chapter three. In addition, thermodynamic analysis i.e. exergy/availability has been described in this chapter. The “Thermosolv” software developed in this study is detailed in chapter four with its structure, functions and operation manual included. In chapter five the outcomes of two case studies using the “Thermosolv” software are presented, with discussions and conclusions about the study in chapters 6 and 7 respectfully. The relevant recommendations are then made in chapter eight.

Reactive ball milling to produce nanocrystalline ZnO

Ball milling of zinc powders in oxygen atmosphere leads to nanocrystalline ZnO. The average grain size has a value of 9 nm. The zinc oxidation proceeds gradually. It is compared with the combustion oxidation reactions of metals (Zr, Ti, Fe and Sn) reported previously. We propose a new parameter ΔH/C_p(metal) instead of simplified adiabatic temperature to judge if the mechanochemical oxidation of a particular metal happens via gradual or combustion reaction.

Stabilisation of brown coal fly ash using geopolymers

This research explores geopolymer technology as a means of stabilising fly ash from power stations. By controlling the synthesis process, geopolymeric materials incorporating fly ash were synthesised. Successful stabilisation of strontium and barium was achieved, though attributed to side reactions. The geopolymer did not contribute significantly to stabilisation of fly ash.

Acid drainage, limnology and bioremediation of western Victorian coal mine lakes

Rehabilitation of Alcoa's Anglesea open cut brown coal mine to a healthy lake has many environmental challenges. The study of regional acid drainage, limnology of Wenslydale Coal Mine Lake and passive bioremediation of acid mine water has shown that a healthy lake can be created.

Multi-point and multi-level solar integration into a conventional coal-fired power plant

Solar-aided power generation (SAPG) is capable of integrating solar thermal energy into a conventional thermal power plant, at multi-points and multi-levels, to replace parts of steam extractions in the regenerative Rankine cycle. The integration assists the power plant to reduce coal (gas) consumption and pollution emission or to increase power output. The overall efficiencies of the SAPG plants with different solar replacements of extraction steam have been studied in this paper. The results indicate that the solar thermal to electricity conversion efficiencies of the SAPG system are higher than those of a solar-alone power plant with the same temperature level of solar input. The efficiency with solar input at 330 °C can be as high as 45% theoretically in a SAPG plant. Even the low-temperature solar heat at about 85 °C can be used in the SAPG system to heat the lower temperature feedwater, and the solar to electricity efficiency is nearly 10%. However, the low-temperature heat resource is very hard to be used for power generation in other types of solar power plants. Therefore, the SAPG plant is one of the most efficient ways for solar thermal power generation.

Maximum likelihood estimation for rician distributed data in analytical q-ball imaging

Analytical q-ball imaging is widely used for reconstruction of orientation distribution function (ODF) using diffusion weighted MRI data. Estimating the spherical harmonic coefficients is a critical step in this method. Least squares (LS) is widely used for this purpose assuming the noise to be additive Gaussian. However, Rician noise is considered as a more appropriate model to describe noise in MR signal. Therefore, the current estimation techniques are valid only for high SNRs with Gaussian distribution approximating the Rician distribution. The aim of this study is to present an estimation approach considering the actual distribution of the data to provide reliable results particularly for the case of low SNR values. Maximum likelihood (ML) is investigated as a more effective estimation method. However, no closed form estimator is presented as the estimator becomes nonlinear for the noise assumption of the Rician distribution. Consequently, the results of LS estimator is used as an initial guess and the more refined answer is achieved using iterative numerical methods. According to the results, the ODFs reconstructed from low SNR data are in close agreement with ODFs reconstructed from high SNRs when Rician distribution is considered. Also, the error between the estimated and actual fiber orientations was compared using ML and LS estimator. In low SNRs, ML estimator achieves less error compared to the LS estimator.