Abnormally high optical transmittance of refractive-index modified ZnO / organic hybrid films

Hybrid films consisting of ZnO nanoparticles and organic matrices were fabricated at particle concentration levels of up to 60 wt%. The correlation between the refractive index and optical transmittance in the visible light region was investigated. The refractive index of the hybrid films was modified in a continuous manner in the range from 1.44 to 1.55. The refractive index increased linearly as a function of particle concentration. On the other hand, optical transmittance showed little change above the particle volume fraction of 0.08.

Photocatalytic activity of manganese-doped ZnO nanocrystalline powders

ZnO nanocrystalline powders doped with up to 5 at% manganese were synthesized and their photocatalytic activity was studied. Doped ZnO powders were prepared using a sol-gel process. The crystal structure and grain size of the particles were characterized by X-ray diffractometry and optical properties were studied using UV-Vis spectroscopy. The photoactivity of undoped and doped ZnO nanocrystalline powders was evaluated by monitoring the photo-bleaching of the aqueous solutions of Rhodamine B dye in the presence of ZnO under simulated sunlight. The results showed that up to 3 at% manganese were successfully doped into the nanocrystalline ZnO and that manganese-doping reduced the photocatalytic activity of ZnO.

Mechanochemical synthesis of nanocrystalline SnO2-ZnO photocatalysts

Mechanochemical processing of anhydrous chloride precursors with Na₂CO₃ has been investigated as a means of manufacturing nanocrystalline SnO₂ doped ZnO photocatalysts. High-energy milling and heat-treatment of a 0.1SnCl₂+0.9ZnCl₂+Na₂CO₃+4NaCl reactant mixture was found to result in the formation of a composite powder consisting of oxide grains embedded within a matrix of NaCl. Subsequent washing with deionized water resulted in removal of the NaCl matrix phase and partial hydration of the oxide reaction product with the consequent formation of ZnSn(OH)₆. The extent of this hydration reaction was found to decrease in a linear fashion with the temperature of the post-milling heat-treatment over the range of 400–700 °C. For a heat-treatment temperature of 700 °C, the SnO₂ doped ZnO powder was found to exhibit significantly higher photocatalytic activity than either single-phase SnO₂ or ZnO powders that were synthesized using similar processing conditions. The heightened photocatalytic activity of the SnO₂ doped ZnO was attributed to its higher specific surface area and the enhanced charge separation arising from the coupling of ZnO with SnO₂.

A novel approach for real mass transformation from V2O5 particles to nanorods

A solid-state, mass-quantity transformation from V2O5 powders to nanorods has been realized via a two-step approach. The nanorods were formed through a controlled nanoscale growth from the nanocrystalline V2O5 phase created by a ball milling treatment. The nanorods grow along the [010] direction and are dominated by {001} surfaces. Surface energy minimization and surface diffusion play important roles in their growth mechanism. Real large quantity production can be achieved when the annealing process is conducted in a fluidized bed which can treat large quantities of the milled materials at once. The crystal orientation of nanorods provides an improved cycling stability for lithium intercalation.

Reactive ball milling to produce nanocrystalline ZnO

Ball milling of zinc powders in oxygen atmosphere leads to nanocrystalline ZnO. The average grain size has a value of 9 nm. The zinc oxidation proceeds gradually. It is compared with the combustion oxidation reactions of metals (Zr, Ti, Fe and Sn) reported previously. We propose a new parameter ΔH/C_p(metal) instead of simplified adiabatic temperature to judge if the mechanochemical oxidation of a particular metal happens via gradual or combustion reaction.

Anomalous evaporation behavior of ZnO powder milled mechanically under high-energy conditions

ZnO powder showed anomalous evaporation behavior after its mechanical milling treatment under high-energy conditions. The amount of generated vapor is about 10 times higher in the first 15 min of annealing at 1300 °C than that of unmilled ZnO powders. The strong ball impacts are responsible for the greatly enhanced evaporation ability. Low-energy ball milling involving shearing actions and rare weak impacts leads only to a small evaporation rate enhancement. The possible explanation of the high evaporation rate of the heavily milled material is the existence of large fraction of weakly bonded atoms in grain boundaries, surface defects and strained areas.

Low temperature solvothermal synthesis of ZnO quantum dots

ZnO quantum dots were synthesized via a low-temperature solvothermal process without using surfactants. Heat treatment of ZnCl2 and NaOH solutions in tetra-ethylene glycol at 140°C led to the formation of spherical ZnO nanoparticles consisting of the aggregates of uniform-sized quantum dots. The particle size and morphology were characterized using transmission electron microscopy, dynamic light scattering, X-ray diffraction, and Brunauer–Emmett–Teller gas absorption measurements. It was found that the quantum dots in the particles were single crystals of ZnO of ∼5 nm in diameter having the wurtzite structure. The quantum dots showed quantum size effects even in the agglomerated form. The growth mechanism of this new type of ZnO nanoparticles is proposed.

Reverse microemulsion-mediated synthesis of SiO2-coated ZnO composite nanoparticles : multiple cores with tunable shell thickness

Monodispersed SiO₂-shell/ZnO-core composite nanospheres have been prepared in an oil-in-water microemulsion system. By using cyclohexane as the oil phase and Triton X-100 as the surfactant, composite nanospheres with high core loading levels and tunable shell thickness were obtained. Utilization of PVP capping agent on ZnO allowed the synthesis of composite nanospheres without forming any coreless SiO2 spheres or shell-less ZnO particles. The photoactivity of ZnO nanoparticles was greatly reduced by SiO2-coating, which enables their applications as durable, safe, and nonreactive UV blockers in plastics, coating, and other products.

Titanium oxide nanorods extracted from ilmenite sands

One dimensional titanium oxides (TiO2) nanorods and nanowires have substantial applications in photocatalytic, nanoelectronic, and photoelectrochemical areas. These applications require large quantities of materials and a production technique suitable for future industry fabrication. We demonstrate here a new method for mass production of TiO2 nanorods from mineral ilmenite sands (FeTiO3). In this process, powder mixtures of ilmenite and activated carbon were first ball milled; the milled samples were then heated twice at two different temperatures. First high-temperature annealing produced metastable titanium oxide phases, and subsequent second low-temperature annealing in N2-5%H2 activates the growth of rutile nanorods. This solid-state growth process allows large-quantity production of rutile nanorods.

Synthesis of silica-coated ZnO nanocomposite : the resonance structure of polyvinyl pyrrolidone (PVP) as a coupling agent

Abstract The preparation of silica-coated ZnO nanocomposite using polyvinyl pyrrolidone (PVP) as a coupling agent was investigated. Transmission electron microscopy analysis revealed that silica has been deposited on the surface of PVP-capped ZnO nanoparticles as a continuous thin layer. Two-dimensional correlation analysis based on the time-dependent UV–vis spectra was introduced to study the interaction governing the deposition of silica on to PVP-capped ZnO. Strong hydrogen bonds formed between the amphiphilic PVP molecules and silica in the silicacoated PVP-capped ZnO composites. The reduced photocatalytic activity of silica-coated ZnO nanoparticles will enhance their performance as durable, safe, and nonreactive UV blockers in plastics, paints, and coating for outdoor textile and timber products.