In vitro testing of zinc oxide sunscreens

The UVA performances of two all-mineral zinc oxide sunscreens are measured following Colipa and ISO procedures and compared to a sunscreen containing only organic actives. It is found that the two sunscreen types yield very different in vitro SPF and UVA results. It shown that the results can be rationalized in terms of the differences in the monochromatic extinction spectra of the two types of sunscreens.

Effects of nano cerium (IV) oxide and zinc oxide particles on biogas production

With an increase in use of nanoparticles (NPs) in day to day products, these particles eventually enter the wastewater treatment plant and get removed from the effluent while getting accumulated in the sludge at ever increasing concentrations. These NPs have a potential for causing inhibition in sludge digestion processes. Therefore, this research focused on the effects of cerium (IV) oxide (CeO2) and zinc oxide (ZnO) NPs on biogas production from sludge. The inhibition effects were investigated by studying toxicity of the said NPs on Escherichia coli. The results showed that CeO2 and ZnO NPs showed some degree of inhibition in biogas production with 65.3% biogas reduction at ZnO NPs at 1000 mg/L concentration. Conversely, CeO2 at low concentration of 10 mg/L lead to an increase biogas generation by 11%. The tolerable exposure concentrations for ZnO were determined to be 100 and 500 mg/L, where the system could overcome the inhibition effect after 14 days of incubation. The bacterial toxicity test showed that both nanoparticles were toxic for bacteria leading to biogas reduction.

Controlled growth of zinc nanowires

Zinc nanowires have been synthesized by heating a mixture of boron and zinc oxide (ZnO) powders at 1050 °C under a nitrogen atmosphere. The influences of the gas flow rate and the substrate character on the nanowire formation were investigated. It was found that higher-flow rate of gas led to the formation of thinner nanowires; while lower-flow rate of gas produced thicker nanowires and even particles due to the higher partial pressure of Zn vapor in this case. Zn nanowires can be produced on alumina and quartz substrates, but not on a stainless-steel substrate under the same or different synthetic conditions. Photoluminescence measurements were conducted on Zn nanowires and particles and weak emission bands at 482 and 493 nm were observed, which may be contributed by the thin ZnO film on the nanowire surface.

Structure and thermal stability of natural rubber reinforced with in situ generated zinc sorbate

In situ prepared zinc disorbate (ZDS) in natural rubber (NR) by the reaction of zinc oxide and sorbic acid was used to reinforce the dicumyl peroxide-cured NR vulcanizate. The changes in mechanical properties of NR vulcanizates after ageing and were determined and the structures and thermal stability of vulcanizates were also analyzed using scanning electron microscope and thermal gravimetric analyzer. The change ratios in tensile strength and elongation at break of NR vulcanizate with theoretic formation of ZDS of 21phr can be increased to -33 from -44 and -27 from -38 after ageing and the initial weight loss temperature of NR vulcanizate can be increased for about 7°C as compared to un-reinforced NR vulcanizate, indicating that the antioxidative behavior and thermal stability of NR can be improved significantly with theoretic formation of ZDS of 21phr.

Emission-based condition monitoring technique for ZnO surge arrester

In this paper, electromagnetic emission at the frequency range of 30MHz to 300MHz is used to detect physical defects on the 22kV outdoor zinc-oxide (ZnO) surge arresters. Different weather conditions combining with artificially created pollution were produced in a laboratory environment and measurements were recorded over a fixed period of time. Pollution due to fine dust particles has been created according to IEC standard under both wet and dry conditions. The aim is to detect the defects (bushing damage) when the surge arrester is subjected to various weather and surface condition. The collected electromagnetic signals were sampled and analyzed using analysis tools such as the autocorrelation coefficient and Wigner-Ville distribution. The results from the present paper indicate that electromagnetic radiation from the defects on surge arrester combining with the adequate analysis tools can be used as a valuable diagnostic tool for power system operator.

An effective approach to grow boron nitride nanowires directly on stainless-steel substrates

When growing one-dimensional (1D) nanomaterials via the vapour–liquid–solid (VLS) model, the substrates usually need to be coated with a layer of catalyst film. In this study, however, an effective approach for the synthesis of boron nitride (BN) nanowires directly onto commercial stainless-steel foils has been demonstrated. Growth occurs by heating boron and zinc oxide (ZnO) powders at 1100 °C under a mixture of nitrogen and hydrogen gas flow (200 ml min−1). The stainless-steel foils played an additional role of catalyst besides substrate during the VLS growth of these BN nanowires. The as-synthesized nanowires emit strong photoluminescence (PL) bands at 515, 535 and 728 nm. In addition, we found that the gas flow rate and the hydrogen content in the gas mixture strongly affected the diameter and yield of the nanowires by changing the relative concentration of the nanowire growth species in the chamber.

A comparative evaluation of the photocatalytic and optical properties of nanoparticulate ZnO synthesised by mechanochemical processing

In this study, mechanochemical processing has been used to manufacture a nanoparticulate powder of ZnO with a controlled particle size and minimal hard agglomeration. The suitability of this ZnO powder for use as either a photocatalyst or an optically transparent UV-filter was evaluated by comparing its optical and photocatalytic properties with those of three commercially available powders that were synthesised by chemical precipitation and flame pyrolysis. The ZnO powder synthesised by mechanochemical processing was found to exhibit high optical transparency and low photocatalytic activity per unit of surface area, which indicates that it is suitable for use in optically transparent UV-filters.

Visibly transparent UV photoprotective compositions

A broad-spectrum UV photoprotective composition is described. The composition is characterized in that the composition comprises mesoporous zinc oxide aggregates having an average aggregate size of at least 0.8 microns dispersed in a carrier and the composition is visibly transparent. Sufficient zinc oxide is included in the composition to achieve an SPF greater than 15, greater than 25, greater than 30, or greater than 50.

Fabrication of ZnO/SiO2 composite nanospheres with high core-loading levels

Monodispersed silica shell / zinc oxide core composite nanospheres were prepared in an oil-in-water microemulsion system. By using cyclohexane as the oil phase and Triton X-100 as the surfactant, nanospheres with a high core loading level and high monodispersity were obtained. The silica coating greatly reduced the photoactivity of ZnO nanoparticles, offering safe and durable applications of ZnO as UV screening agents.

RGO/ZnO nanocomposite: an efficient, sustainable, heterogeneous, amphiphilic catalyst for synthesis of 3-substituted indoles in water

A nanocomposite consisting of reduced graphene oxide and zinc oxide nanoparticles (RGO/ZnO) with unique structural features was developed as an efficient, sustainable, amphiphilic, heterogeneous catalyst for the synthesis of various 3-substituted indoles in water. The catalyst was recycled six times without significant loss in catalytic activity. The higher environmental compatibility and sustainability factors such as smaller E-factor and higher atom economy make the present methodology a true green and sustainable process for the synthesis of various biologically important 3-substituted indoles.