Needleless electrospinning of uniform nanofibers using spiral coil spinnerets

Polyvinyl alcohol nanofibers were prepared by a needleless electrospinning technique using a rotating spiral wire coil as spinneret. The influences of coil dimension (e.g., coil length, coil diameter, spiral distance, and wire diameter) and operating parameters (e.g., applied voltage and spinning distance) on electrospinning process, nanofiber diameter, and fiber productivity were examined. It was found that the coil dimension had a considerable influence on the nanofiber production rate, but minor effect on the fiber diameter. The fiber production rate increased with the increased coil length or coil diameter, or the reduced spiral distance or wire diameter. Higher applied voltage or shorter collecting distance also improved the fiber production rate but had little influence on the fiber diameter. Compared with the conventional needle electrospinning, the coil electrospinning produced finer fibers with a narrower diameter distribution. A finite element method was used to analyze the electric field on the coil surface and in electrospinning zone. It was revealed that the high electric field intensity was concentrated on the coil surface, and the intensity was highly dependent on the coil dimension, which can be used to explain the electrospinning performances of coils. In addition, PAN nanofibers were prepared using the same needleless electrospinning technique to verify the improvement in productivity.

Studying non-uniform electrodeposition using the wire beam electrode method

Nonuniform electrodeposition is a major concern in almost every practical electrodeposition application. The ablility to control nonuniformity in electrodeposition is the key to successful plating for corrosion resistance, and more especially to meeting the very exacting requirements of electroforming, electrodeposition. This paper presents a novel technique namely the wire beam electrode (WBE) for characterizing and monitoring nonuniform electroplating processes. For the first time, the nonuniform distribution of electroplating currents (NDEC) has been mapped. Preliminary experimental results indicated that electrochemical heterogeneity was the key factor affecting NDEC. The secondary current distribution, rather than the primary current distribution, played a major role in determining the NDEC. This work suggests that the WBE is a practical tool for characterizing and optimizing electrodeposition processes and for verifying the accuracy and completeness of mathematic modelling of electrodeposition processes.

Non-uniform sparsity in rapid compressive sensing MRI

Magnetic Resonance Imaging (MRI) is one of the prominent medical imaging techniques. This process is time-consuming and can take several minutes to acquire one image. The aim of this research is to reduce the imaging process time of MRI. This issue is addressed by reducing the number of acquired measurements using theory of Compressive Sensing (CS). Compressive Sensing exploits sparsity in MR images. Randomly under sampled k-space generates incoherent noise which can be handled using a nonlinear image reconstruction method. In this paper, a new framework is presented based on the idea to exploit non-uniform nature of sparsity in MR images, where local sparsity constrains were used instead of traditional global constraint, to further reduce the sample set. Experimental results and comparison with CS using global constraint are demonstrated.

An argument for uniform Australian sentencing law

Sentencing law and practice impacts on fundamental individual interests, both from the perspective of offenders and victims. It also affects community safety and security The scope of sentencing law and its principal objectives are broadly similar throughout Australia. However, there are many important differences, especially in relation to sentencing practice, with some jurisdictions appearing to impose considerably heavier penalties for certain offence types. This article argues that uniform sentencing law should be implemented throughout Australia. The likely benefits would extend beyond achieving greater consistency in sentencing outcomes. A move toward uniform national sentencing laws would provide the catalyst for an objective, evidence-based review of sentencing policy and practice, thereby providing a vehicle for harmonising the law with a wealth of empirical data regarding the objectives that can be achieved through a system of state-imposed sanctions. It would also present a meaningful opportunity for a normative assessment of the justifiable operation of sentencing law. The main impediment to uniform sentencing laws is likely to come from state and territory governments seeking to maintain control over this often socially controversial area as a means of securing and maintaining community support. However, this obstacle is not necessarily insurmountable. It is not clear whether sentencing policy is, in fact, a main driver of voter preferences. Some politicians may prefer to have ·national uniformity' as a buffer to counteract reflexive calls for tougher sentencing that often occur following particularly serious crimes or seemingly light sentences handed down by courts.

Uniform elongation and the stress-strain flow curve of steels calculated from hardness using empirical correlations

An empirical relationship between the hardness and uniform elongation of non-Austenitic hypoeutectoid steels has been developed. This new hardness-elongation relationship was combined with previously developed correlations of hardness and strength (yield and ultimate tensile strength) to predict the stressstrain flow curve from a single hardness test. The current study considers both power law hardening behavior and exponential hardening behavior. Reasonable agreement was observed between the experimental and predicted flow curves of a high strength, low alloy steel. Additionally, an empirical correlation of the flow strength at instability with hardness is provided. © ASM International.

How does the cookie crumble? legal costs under a uniform interpretation of the United Nations Convention on Contracts for the International Sale of Goods

A family owned Mexican company, Zapata Hermanos Sucesores, S.A. ("Zapata"), sold approximately US$950,000 worth of cookie tins over a period of four years to the Maurice Lenell Cooky Company ("Lenell"), an American company that produced baked goods. Lenell failed to pay Zapata for the cookie tins so Zapata sought legal advice and instituted legal proceedings against Lenell for breach of contract in the Federal District Court of Illinios. The cookie tin sale contracts were governed by the United Nations Convention on Contracts for the International Sale of Goods ("CISG"). Zapata succeeded in its Federal District Court claim and, as part of the Court's order, was awarded US$550,000 as foreseeable loss under Article 74 of the CISG, being the amount of legal fees incurred by Zapata in bringing proceedings against Lenell. On appeal to the Federal Appellate Court, however, the award of legal fees was overturned. The parties now find themselves contesting a leave application to appeal to the Supreme Court of the United States of America in a much anticipated debate over who should pay the lawyers.