T-Shaped equi-channel angular pressing of Pb-Sn eutectic and its tensile properties

Equi-channel angular pressing (ECAP) of a Pb–Sn eutectic alloy up to six passes in a T-shaped die, rather than a conventional L-shaped die, was studied for grain refinement. The effect of ECAP on the hardness and tensile properties was studied. Microstructure predominately changed in the early part of the ECAP process and became equiaxed and uniformly distributed in both the longitudinal and the transverse sections after four passes. There occurred substantial softening over the first two passes—hardness of 10 Hv, yield strength of 14.2 MPa and tensile strength of 16.3 MPa in the as-cast condition decreased upon two passes to 6 Hv, 9.7 MPa and 13.0 MPa, respectively. The ductility (% elongation) increased drastically from <50% in the as-cast condition to 150% upon two passes, and further increased to 230% after four passes. Various tensile properties and concurrent microstructural evolution were used to develop a mutual relationship among them.

Tensile behaviour of wool fabric as a function of fabric pH

Wool fabric extensibility under a 5 N/cm load was observed to be greatest at the wool isoelectric point of pH 4.8 and lower at both pH 2.1 and pH 7.2. The impact of pH on fabric extensibility is similar to the variation in fabric hygral expansion previously observed. Fabric stress-strain curves at different pHs show that for a given fabric extension level, the work required to stretch a fabric was less at pH 2.1 than at pH 4.8. These results confirm the fact that the strength of wool fabric is at a maximum when the pH of the fibres is close to the isoelectric point.

In-situ tensile properties of a ballooning staple yarn

This study investigated the tensile properties of a rotating or ballooning staple yarn. The results indicated that the effect of rotating speed on the tensile properties of a ballooning staple yarn was significant. As the yarn rotating speed increased, the tenacity of the rotating or ballooning yarn decreased, while the yarn breaking elongation increased. The effect of rotating speed on the tenacity of a ballooning staple yarn varied for different yarns. These results demonstrated that the breaking force of a ballooning yarn was much lower than the yarn breaking force obtained from normal tensile tests. These results provide new insight into the problems of yarn breakage in yarn spinning and twisting processes.

Tensile behaviour of non-uniform fibres and fibrous composites

This work investigates the tensile behaviour of non-uniform fibres and fibrous composites. Wool fibres are used as an example of non-uniform fibres because they're physical, morphological and geometrical properties vary greatly not only between fibres but also within a fibre. The focus of this work is on the effect of both between-fibre and within-fibre diameter variations on fibre tensile behaviour. In addition, fit to the Weibull distribution by the non-brittle and non-uniform visco-elastic wool fibres is examined, and the Weibull model is developed further for non-uniform fibres with diameter variation along the fibre length. A novel model fibre composite is introduced to facilitate the investigation into the tensile behaviour of fibre-reinforced composites. This work first confirms that for processed wool, its coefficient of variation in break force can be predicted from that of minimum fibre diameters, and the prediction is better for longer fibres. This implies that even for processed wool, fibre breakage is closely associated with the occurrence of thin sections along a fibre, and damage to fibres during processing is not the main cause of fibre breakage. The effect of along-fibre diameter variation on fibre tensile behaviour of scoured wool and mohair is examined next. Only wet wool samples were examined in the past. The extensions of individual segments of single non-uniform fibres are measured at different strain levels. An important finding is the maximum extension (%) (Normally at the thinnest section) equals the average fibre extension (%) plus the diameter variation (CV %) among the fibre segments. This relationship has not been reported before. During a tensile test, it is only the average fibre extension that is measured. The third part of this work is on the applicability of Weibull distribution to the strength of non-uniform visco-elastic wool fibres. Little work has been done for wool fibres in this area, even though the Weibull model has been widely applied to many brittle fibres. An improved Weibull model incorporating within-fibre diameter variations has been developed for non-uniform fibres. This model predicts the gauge length effect more accurately than the conventional Weibull model. In studies of fibre-reinforced composites, ideal composite specimens are usually prepared and used in the experiments. Sample preparation has been a tedious process. A novel fibre reinforced composite is developed and used in this work to investigate the tensile behaviour of fibre-reinforced composites. The results obtained from the novel composite specimen are consistent with that obtained from the normal specimens.

Experimental evaluation of curl and tensile properties of advanced high strength sheet steels

The response of HSLA steel, 590R, and dual-phase steel, DP-600, to non-uniform deformation imposed in a laboratory Bending-Under-Tension (BUT) test apparatus was evaluated. Samples were deformed with both low and high back tension forces at bend angles of 45 and 90 degrees, and evaluated to determine the ""side-wall curl,"" i.e., the curvature in the sheet section in contact with the die. The results indicate that there are no consistent differences between the two steels, 590R and DP-600. It was found that back tension, tensile strength and sheet thickness were the primary factors affecting curl. The bend angle has an influence on curl, with the curl radius at a 90ø bend angle being greater than the curl radius at a 45\mD bend angle.

High strain rate tensile properties of rapidly cured woven carbon fibre composites

Tensile tests at high speeds corresponding to automotive crash events were conducted to understand the dynamic properties of rapidly cured woven carbon fiber composites. The High Strain Rate (HSR) experiments were conducted on a servo-hydraulic machine at constant velocities up to a maximum of 25 m/s (82 ft/s). Results from HSR tests were compared with the static results to determine the rate sensitivity of the composite. A high speed camera was used to capture the failure at HSR. The tensile properties of rapidly cured laminate were compared to oven cured laminate to justify its productivity while maintaining the desired properties. The methodology used to achieve constant velocity during HSR tests is discussed in detail. The specimen geometry was specially designed to suit the test rig and to achieve high speeds during tests. All the specimens failed with linear elasticity until sudden brittle fracture. The Scanning Electron Microscopy (SEM) images of the fracture zone were used to identify the failure modes observed at static and high strain rates.

Microstructure-property relationship of the high strength low alloy steels during tensile testing at high strain rates

Positive The influence of strain-rate on the room temperature mechanical properties of the Dual-Phase and Transformation Induced Plasticity (TRIP) steels was investigated.The results showed that both the plastic strain, and strength properties increased with increasing strain rates at high strain rates.At strain rates lower than approximateil 1s ~ (-1) the properties no longer have an advantageous proportionality to strain rate and remain strain rate neutral.Possible explanations are offered for trends exhibited, in terms of thermal and athermal considerations, in relation to the respective microstructures of the two steels

Effect of thermomechanical processing on the microstructure and retained austenite stability during in situ tensile testing using synchrotron X-Ray diffraction of NbMoAl TRIP steel

In this work we compare and contrast the stability of retained austenite during tensile testing of Nb-Mo-Al transformation-induced plasticity steel subjected to different thermomechanical processing schedules. The obtained microstructures were characterised using optical metallography, transmission electron microscopy and X-ray diffraction. The transformation of retained austenite to martensite under tensile loading was observed by in-situ high energy X-ray diffraction at 1ID / APS. It has been shown that the variations in the microstructure of the steel, such as volume fractions of present phases, their morphology and dimensions, play a critical role in the strain-induced transition of retained austenite to martensite.

Strip twisted electrospun nanofiber yarns: Structural effects on tensile properties

Nanofiber yarns with controlled twist levels were prepared by twisting a narrow fibrous strip cut directly from electrospun nanofiber mats. The effects of fiber morphology, diameter and orientation, as well as the yarn twist level on the yarn tensile properties were examined. For the yarns made from randomly oriented fine uniform nanofibers (e.g., diameter 359 nm) and beaded nanofibers, the tensile strength increased with increasing the yarn twist level. Higher fiber diameter (e.g., 634 nm) led to the tensile strength having an initial increase and then decrease trend. The modulus increased with the twist level for all the yarns studied. However, the elongation at break increased initially with the twist level and subsequently decreased. The orientation of aligned fibers within the fiber strip greatly influenced the yarn tensile properties. When the fibers were oriented along the fiber length direction, both tensile strength and modulus were the largest.