Solar heating systems for recirculation aquaculture

The literature over the past 25 years indicates that there has been a continued interest in using passive and active solar technologies to reduce the conventional energy required to maintain water temperatures in small recirculation aquaculture systems. Although all of the experimental systems reviewed report favourable results, there is little information available to guide system designers. This paper describes the use of a simulation model to predict the annual conventional energy consumption of a 10.6 m3 RAS enclosed in a double layer polyethylene greenhouse in two different climates. The water was maintained at 22.5 °C and the recirculation rate was 10% of tank volume per day. Simple unglazed solar collectors have also been combined with the greenhouse to further reduce energy consumption. The effect of increasing collector area on the solar fraction and utilization of useful energy was predicted. Finally, the model was used to investigate the relationship between the occurrence of condensation on the inner cover, ventilation rates and energy use. It was found that in a hot dry climate, the greenhouse alone was sufficient to reduce the conventional energy requirements by 87%; while in the cooler temperate climate reductions of 66% were possible. When solar collectors were added to the system, conventional energy requirements were reduced further and depended on the area of collector used. For example, in the temperate climate location, conventional energy requirements were reduced to 23% of a RAS enclosed in a non-solar building when 26 m2 of solar collector inclined at the optimum angle for winter energy collection were used. Although condensation could be successfully reduced by ventilation of the greenhouse, this increased conventional energy requirements because the potential for evaporation was increased. Covering the tanks at night was found to be a more effective strategy because it reduced condensation and conventional energy use simultaneously.

Seasonal storage for solar thermal systems in Australia?

Seasonal storage systems have been operating in various European countries since 1985. Combined with solar collectors, these systems are known as ‘central solar heating plants with seasonal storage’ (CSHPSS). While these systems have been shown to be technically feasible, their cost is still too high to make them competitive with fossil fuels.

In Australia, we have quite different conditions to those countries where CSHPSS have been trialled. In general, we experience higher radiation levels, ambient temperatures and cooling loads. Our heating loads and energy prices are also usually lower. As a result, any evaluation of CSPSS operating in a European context may not be valid for Australian conditions. To the authors’ knowledge, no evaluation of these systems has been carried out for Australia.

This paper therefore attempts an initial assessment of these systems and their viability for Australia. The paper first describes the various types of CSHPSS and then reviews their current status. The performance of one type of CSHPSS operating in several locations of Australia has been predicted using a TRNSYS model. The simulations indicated that the design guidelines for Europe are inappropriate for Australia and would result in greatly over-sized systems.

An indication of the financial viability of the system was determined by calculating a simple payback period for a variety of fossil fuels. This type of seasonal storage systems appears to be financially attractive in areas of southern Australia where the solar system is displacing LPG.

Performance of a 120 m2 solar air heater for a commercial building in Victoria

The operation of two 60 m² solar air heaters serving a large studio teaching space has been monitored for a twelve month period. The solar contribution of the heaters was found to be less than 5%, and in some instances the heaters actually contributed to the space heating load. A validated mathematical model of the studio and it’s heating, ventilation and air conditioning system was used to investigate performance improvement strategies. It was found a different control strategy and recommissioned control sensors would substantially improve the solar air heater performance.

Simulation of the solar adsorption refrigeration operating at near atmospheric pressure

To solve the leaking problem faced by current vacuum adsorption refrigeration systems, the authors have carried out a series of studies on the concept of raising the system's pressure to around atmospheric pressure with an inert gas (eg. Helium) as the pressure-adjusting agent. This paper presents the simulation of the performance oj the activated carbon-methanol adsorption refrigeration operating at near atmospheric pressure powered by solar energy. This simulation can be refereed in the prototype design.

A typical meteorological year for energy simulations in Hamilton, New Zealand

Typical Meteorological Year (TMY) data is used extensively in building energy simulations and solar energy analysis. TMY data for New Zealand, however, is relatively limited and no such data existed for Hamilton. Ten years of hourly meteorological data was analysed, and a TMY was developed. Simulations using the TMY data were conducted to determine the performance of a solar pool-heating system. It was found that the TMY was able to predict the annual performance of this system to within 2% of the long-term mean. It is intended that this TMY could be used to perform simulations on building energy use and solar heating systems in Hamilton.

Development of a building integrated photovoltaic/thermal solar collector based on steel roofing

The use of onsite renewable energy cogeneration from structural building elements is a relatively new concept, and one that is gaining considerable interest in the building industry. In this study the design, development, testing and production methods for a novel building integrated photovoltaic/thermal (BIPVT) solar energy cogeneration system are examined and discussed.

During the analysis of the design, adhesives (ADH), resistance seam welding (RSW) and autoclaving (ATC) were identified as the most appropriate for fabricating BIPVT panels for roofing and façade applications. Of these manufacturing methods ADH was found to be most suitable for low volume production systems due to its low capital cost.

Furthermore, a prototype panel was fabricated using ADH methods and exhibited good thermal performance. In addition it was shown, using experimental testing, that the performance of a BIPVT could be theoretically predicted using a one-dimensional heat transfer model. Furthermore, the model was used to suggest further improvements that could be made to the design. Finally, a transient simulation of the BIPVT was performed in TRNSYS and was used to illustrate the long term benefits of the system.

Application of the Hottel-Whillier equations to the analysis of a building integrated photovoltaic/thermal solar collector

The idea of combining photovoltaic and solar thermal collectors (PVT collectors) to provide electrical and heat energy is not new, however it is an area that has received only limited attention. With concern growing over energy sources and their usage, PVTs have become an area receiving more attention. Although PVTs are not as prevalent as solar thermal systems, the integration of photovoltaic and solar thermal collectors into the walls or roofing structure of a building could provide greater opportunity for the use of renewable solar energy technologies in domestic, commercial and industrial applications. As such, the design of a novel building integrated photovoltaic/thermal (BIPVT) solar collector is theoretically analysed through the use of a modified Hottel-Whillier model. The thermal and electrical efficiency under a range of conditions are subsequently determined and results showing how key design parameters influence the performance of the BIPVT system are presented.

Designing a low cost solar collector system for process industry applications

New Zealand is a large producer and processor of primary products and has a climate with high levels of solar radiation. However, the use of solar energy for heating and cooling in the processing industries has received limited attention.
For this study, the design of a low cost solar collector is analysed and discussed. Furthermore, the methods for integrating the collector into water heating and cooling systems in a hypothetical processing environment are examined. An F-Chart analysis is used to simulate the performance of large-area arrays of the solar collector and to determine its potential contribution to heating and cooling loads.
The study shows that for a storage-based system, the contribution of solar energy is determined mainly by the collector area to storage volume ratio. It is suggested that this low cost collector could make a significant contribution to energy use in processing plants and may be an attractive future technology.

The feasibility of a sustainable energy, driver-only electric commuter vehicle for New Zealand

This paper investigates whether low technology driver-only, battery electric commuter vehicles are feasible for New Zealand. Personal passenger transport faces several challenges in the coming decades: depletion of cheap oil reserves, increasing congestion, localised pollution, the need for reduced carbon emissions and the long term goal of sustainability. One way of solving some of these problems could be to introduce low cost, comfortable, energy efficient, driver-only electric vehicles. These would still give the driver a weatherproof, safe and comfortable means of commuting, but at a fraction of the energy and running costs of conventional petrol/diesel cars. To help assess their viability, the performance and energy use of the E-POD electric commuter vehicle is used as a benchmark. The work shows that such a vehicle could be made cheaply, using readily available technology with a range of 180km and a top speed of over 90km/h. The chassis could be made from natural fibre composite materials that might reduce significantly the embedded energy required for its manufacture. The electricity taken from the grid to charge the batteries could be replaced by electricity generated from grid connected photovoltaic panels mounted on the garage roof of the vehicle owner.

Solar thermal aided power generation

Fossil fuel based power generation is and will still be the back bone of our world economy, albeit such form of power generation significantly contributes to global CO2 emissions. Solar energy is a clean, environmental friendly energy source for power generation, however solar photovoltaic electricity generation is not practical for large commercial scales due to its cost and high-tech nature. Solar thermal is another way to use solar energy to generate power. Many attempts to establish solar (solo) thermal power stations have been practiced all over the world. Although there are some advantages in solo solar thermal power systems, the efficiencies and costs of these systems are not so attractive. Alternately by modifying, if possible, the existing coal-fired power stations to generate green sustainable power, a much more efficient means of power generation can be reached. This paper presents the concept of solar aided power generation in conventional coal-fired power stations, i.e., integrating solar (thermal) energy into conventional fossil fuelled power generation cycles (termed as solar aided thermal power). The solar aided power generation (SAPG) concept has technically been derived to use the strong points of the two technologies (traditional regenerative Rankine cycle with relatively higher efficiency and solar heating at relatively low temperature range). The SAPG does not only contribute to increase the efficiencies of the conventional power station and reduce its emission of the greenhouse gases, but also provides a better way to use solar heat to generate the power. This paper presents the advantages of the SAPG at conceptual level.

Performance of building integrated solar hot water systems

The integration of solar energy systems into buildings has been the subject of considerable commercial and academic research, particularly building integrated photovoltaics. However, the integration of solar hot water systems into roofing systems has had far less attention. This paper presents the theoretical and experimental results of a novel building integrated solar hot water system developed using existing long run roofing materials.

This work shows that it is possible to achieve effective integration that maintains the aesthetics of the building and also provides useful thermal energy. The results of an unglazed 108m2 swimming pool heater and 8m2 glazed domestic hot water systems are presented.

The experimental results show that the glazed system performs close to the theoretical model and is an effective provider of hot water in certain climates. However it was also found that for larger scale building integrated solar water heating systems, special attention must be paid to the configuration and arrangement of the collectors in order to minimise problems with respect to flow distribution and its effect on collector and system efficiency.

Organic ionic plastic crystal electrolytes; a new class of electrolyte for high efficiency solid state dye-sensitized solar cells

Dye-sensitized solar cells are an increasingly promising alternative to conventional silicon solar cells as a method of converting solar energy to electricity and thus providing an effectively inexhaustible energy source. However, the most efficient of these devices currently utilize liquid electrolytes, which suffer from the associated problems of leakage and evaporation. Hence, significant research is currently focused on the development of solid state alternatives. Here we report a new class of solid state electrolyte for these devices, organic ionic plastic crystal electrolytes, that allow relatively rapid diffusion of the redox couple through the matrix, which is critical to the cell performance. A range of different organic ionic plastic crystal materials, utilizing different cation and anion structures, have been investigated and the conductivities, diffusion rates and photovoltaic performance of the electrolytes are reported. The best material, utilizing the dicyanamide anion, achieves efficiencies of more than 5%.