Enhancing thermal stability and mechanical properties of lyotropic liquid crystals through incorporation of a polymerizable surfactant.

We present a facile method to prepare thermally stable and mechanically robust crosslinked lyotropic liquid crystals (LLCs) through incorporation of a polymerizable amphiphile into a binary LLC system comprising commercially available surfactant Brij 97 and water. Thermal stability and mechanical properties of the polymerized LLCs were significantly enhanced after polymerization of the incorporated polymerizable surfactant. The effect of incorporating a polymerizable amphiphile on the phase behavior of the LLC system was studied in detail. In situ photo-rheology was used to monitor the change in the mechanical properties of the LLCs, namely the storage modulus, loss modulus, and viscosity, upon polymerization. The retention of the LLC nanostructures was evaluated by small angle X-ray scattering (SAXS). The ability to control the thermal stability and mechanical strength of LLCs simply by adding a polymerizable amphiphile, without tedious organic synthesis or harsh polymerization conditions, could prove highly advantageous in the preparation of robust nanomaterials with well-defined periodic structures.

Stabilizing and destabilizing protein surfactant-based foams in the presence of a chemical surfactant: Effect of adsorption kinetics.

Stimuli-responsive protein surfactants promise alternative foaming materials that can be made from renewable sources. However, the cost of protein surfactants is still higher than their chemical counterparts. In order to reduce the required amount of protein surfactant for foaming, we investigated the foaming and adsorption properties of the protein surfactant, DAMP4, with addition of low concentrations of the chemical surfactant sodium dodecylsulfate (SDS). The results show that the small addition of SDS can enhance foaming functions of DAMP4 at a lowered protein concentration. Dynamic surface tension measurements suggest that there is a synergy between DAMP4 and SDS which enhances adsorption kinetics of DAMP4 at the initial stage of adsorption (first 60s), which in turn stabilizes protein foams. Further interfacial properties were revealed by X-ray reflectometry measurements, showing that there is a re-arrangement of adsorbed protein-surfactant layer over a long period of 1h. Importantly, the foaming switchability of DAMP4 by metal ions is not affected by the presence of SDS, and foams can be switched off by the addition of zinc ions at permissive pH. This work provides fundamental knowledge to guide formulation using a mixture of protein and chemical surfactants towards a high performance of foaming at a low cost.

The charge effect of cationic surfactants on the elimination of fibre beads in the electrospinning of polystyrene

Polystyrene nanofibres were electrospun with the inclusion of cationic surfactants, dodecyltrimethylammonium bromide (DTAB) or tetrabutylammonium chloride (TBAC), in the polymer solution. A small amount of cationic surfactant effectively stopped the formation of beaded fibres during the electrospinning. The cationic surfactants were also found to improve the solution conductivity, but had no effect on the viscosity. Only DTAB had an effect on the surface tension of the polymer solution, the surface tension decreasing slightly with an increase in the concentration of DTAB.

The formation of beaded fibres was attributed to an insufficient stretch of the filaments during the whipping of the jet, due to a low charge density. Adding the cationic surfactants improved the net charge density that enhanced the whipping instability. The jet was stretched under stronger charge repulsion and at a higher speed, resulting in an exhaustion of the bead structure. In addition, a polymer/surfactant interaction was found in the polystyrene–DTAB solution system, while this interaction was not found in the polystyrene–TBAC system. The polymer/surfactant interaction led to the formation of thinner fibres than those formed in the absence of the interaction.

The effects of a non-ionic surfactant, Triton X-405, on the electrospun fibres were also studied. The addition of Triton X-405 did not eliminate the fibre beads, but reduced the bead numbers and changed the morphology. Triton X-405 slightly improved the solution conductivity, and had a minor effect on the surface tension, but no effect on the viscosity.

A comparative study on preparation of TiO2 pellets as photocatalysts based on different precursors

The porous Ti0₂ pellets were prepared based on pigment grade titaina, P25 titania powder and titaniurn(lV) butoxide. The characterization was done with X-Ray diffraction, scanning electron microscopy and BET measurements. The result shows that Ti0₂ pellets by using titaniurn(IV) butoxide with some addictive have the best surface porosity, with specific surface area of 196.9m²/g. For pigment grade titania and P25 titania powder, it is still effective to enhance the surface area after reassembling. The surface area increased from 11.6 to 29.2 m²/g for pigment grade titania and from 50 to 84.4 m²/g for P25 titania powder. Furthermore, it has been investigated on how to optimize and get the highest surface area by controlling the sintering temperature, reaction temperature, pH of solution, and the amount of alcohol and addictive of surfactant during preparation. The experimental photocatalytic degradation of acetone and toluene was performed using titania pellets made from P25 titania powder.

Polypyrrole nanoparticles and dye absorption properties

Polypyrrole (PPy) nanoparticles were prepared by using microemulsion polymerization processes at 3 °C. Particle characterization was performed by using FTIR, elementary analysis, UV–vis spectra and scanning electron microscope (SEM). The size of the nanoparticles varied from about 50 to 100 to 100 to 200 nm with the change in concentration of surfactant from 0.8 to 0.44 M. Polypyrrole nanoparticles were dedoped by a 10% NaOH solution, followed by a redoping process using a nuclear fast red kernechtrot dye, which has a sulfonate group. Dedoping changed the optical absorption properties of the nanoparticles.

Morphological evolution of nanofibers during electrospinning

Electrospinning is a very useful technique to produce polymeric nanofibers. It involves fast-drawing a polymer fluid into nanofibers under a strong electric filed, and depositing randomly on an electrode collector to form non-woven nanofiber mat in most cases [1]. The fibre stretching during electrospinning is a fast and incessant process which can be divided into three consecutive stages: jet initiation, whipping instability and fibre deposition. From the initial jet to dry fibres, the fibre stretching takes place in milliseconds, so it has been hardly so far to observe fiber morphology changes by any normal methods, such as high speed photography [2-5]. In this study, we used a facile and practical approach to realize the observation of nanofiber morphology changes during electrospinning. Through a special collection device with coagulation bath, newly electrospun nanofibers can be solidified at different electro spinning distances, and by associating the fiber morphology with the electrospinning distance (d), the morphological evolution of nanofibers can be established. We used polyacrylonitrile (PAN) and polystyrene (PS) as two model polymers to demonstrate this method in present research. From experimental results, we found the massive jet-thinning happens at the initial stage of the process. The formation of uniform PAN nanofibers (7%) and the beads structure changes on beads-on-string PAN nanofibers (5%) have also been successful observed. Using the same method, we also observed PS nanofiber (10%) morphology changes to understand the beads formation 011 nanofibers during electrospinning process, and how the beads was eliminated when ionic surfactant is added into the PS solution for electrospinning.

Characterisation of nickel(II) extraction by 2-hydroxy-5-nonylacetophenone oxime (LIX 84) in a micellar phase

The properties of the nickel(II)/2-hydroxy-5-nonylacetophenone oxime (HNAPO), an active ingredient in LIX 84, extraction system were characterised in a micellar system. The extinction coefficient, λ_max of HNAPO (316 nm) and the Ni²⁺ complex (387 nm) in a neutral micellar system, poly dispersed octa-ethyleneglycol mono-n-dodecyl ether (G₁₂A₈) were determined as 3100 and 3500 M⁻¹ cm⁻¹, respectively. HNAPO was found to have a neutral micellar phase and bulk aqueous phase pK_a of 11.5 and 12.5, respectively. The extraction equilibrium constant, K_ex, was determined to be 10^−8.0, and the deviation from theory observed at high pH can be accounted for by consideration of the competition for nickel(II) ions by hydroxide ions and HNAPO. A micellar phase of octa-ethyleneglycol mono-n-dodecyl ether (C₁₂E₈) was determined to be an appropriate model of the free oil/water interface from the solubilised location of HNAPO. Utilising the interfacial probe, 4-heptadecyl-7-hydroxy coumarin (HHC) allowed the determination of the electrostatic surface potential of mixed micelles of G₁₂A₈ and sodium dodecyl sulphate (SDS) or dodecyl trimethyl ammonium chloride (DTAC). The electrostatic surface potential was a linear function of the number of additional surfactant monomers within the G₁₂A₈ micelle, for the concentration range studied. For G₁₂A₈/DTAC mixed micelles, the surface potential was given by +1.1 mV per DTAC molecule per micelle, and for G₁₂A₈/SDS mixed micelles the relationship was −1.4 mV per SDS molecule per micelle.

The optimisation of ultrasonic cleaning procedures for dairy fouled ultrafiltration membranes

Ultrafiltration (UF) of whey is a major membrane based process in the dairy industry. However, commercialization of this application has been limited by membrane fouling, which has a detrimental influence on the permeation rate. There are a number of different chemical and physical cleaning methods currently used for cleaning a fouled membrane. It has been suggested that the cleaning frequency and the severity of such cleaning procedures control the membrane lifetime. The development of an optimal cleaning strategy should therefore have a direct implication on the process economics. Recently, the use of ultrasound has attracted considerable interest as an alternative approach to the conventional methods. In the present study, we have studied the ultrasonic cleaning of polysulfone ultrafiltration membranes fouled with dairy whey solutions. The effects of a number of cleaning process parameters have been examined in the presence of ultrasound and results compared with the conventional operation. Experiments were conducted using a small single sheet membrane unit that was immersed totally within an ultrasonic bath. Results show that ultrasonic cleaning improves the cleaning efficiency under all experimental conditions. The ultrasonic effect is more significant in the absence of surfactant, but is less influenced by temperature and transmembrane pressure. Our results suggest that the ultrasonic energy acts primarily by increasing the turbulence within the cleaning solution.

Reverse microemulsion-mediated synthesis of SiO2-coated ZnO composite nanoparticles : multiple cores with tunable shell thickness

Monodispersed SiO₂-shell/ZnO-core composite nanospheres have been prepared in an oil-in-water microemulsion system. By using cyclohexane as the oil phase and Triton X-100 as the surfactant, composite nanospheres with high core loading levels and tunable shell thickness were obtained. Utilization of PVP capping agent on ZnO allowed the synthesis of composite nanospheres without forming any coreless SiO2 spheres or shell-less ZnO particles. The photoactivity of ZnO nanoparticles was greatly reduced by SiO2-coating, which enables their applications as durable, safe, and nonreactive UV blockers in plastics, coating, and other products.

Self-assembly and film stability of a micelle of a single-chain quaternary ammonium amphiphile containing azobenzene on mica

The self-assembling behavior of a single-chain quaternary ammonium amphiphile bearing azobenzene (C₁₂AzoC₆N⁺) on freshly cleaved mica sheet has been investigated by atomic force microscopy (AFM) method. Confocal microscopic Raman spectra confirm the adsorption of the self-assembled monolayer structure. Ex-situ AFM reveals that C₁₂AzoC₆N⁺ forms branch-like stripes indicating the fusion and reorganization of the micelles during drying in air as the in-situ AFM has revealed that surfactant forms spherical micelles on the mica surface. The nano-sized surface structure is strongly dependent on the change of molecular structure, which resulted from photo-induced isomerization. The nano-sized stripe is quite stable even being annealed at 90 °C for 4 h.

In situ observation of the aggregated morphology and interaction of dialkyldimethylammonium bromide with DNA at air/water interface by Brewster angle microscopy

The adsorption of DNA on the Langmuir film of a cationic surfactant, dioctadecyldimethylammonium bromide (DODA·Br), and the change of the aggregation morphology of the composite monolayer with respect to surface pressure have been investigated by Brewster angle microscopy (BAM). In contrast with the case of DODA·Br on pure water subphase, when DNA was dispersed into subphase, its adsorption to the interface monolayer through electrostatic interaction decreases the charge density and therefore promotes the formation of domain at low surface pressure. In addition, the electrostatic interaction changed the phase morphology of DODA·Br Langmuir monolayer under different surface pressure, that is, from flower-shaped crystalline domain on the pure water subphase to circular domain on the subphase dispersed with DNA. The result also shows that the monolayer of the composite at air/water interface under the high pressure is not homogeneous, but consists of incompletely fused domains. For the Langmuir film of the surfactant with shorter alkyl-chains, similar morphology can be observed both under the high and low surface pressure. But the tight-stacked circular domain is no longer observed.

The miscibility of poly(d,l-lactide-co-glycolide) with amphiphilic molecules and the interaction of their mixtures with DNA at air/water interface

The miscibility of poly(d,l-lactide-co-glycolide) (PLG) with three amphiphilic molecules and the interaction of the PLG/surfactant mixtures with DNA at air/water interface are investigated by π-A isotherms, Brewster angle microscopy (BAM) and atomic force microscopy (AFM) techniques. The π-A isotherms of the PLG mixtures with cationic C12AzoC6PyBr, and C12AzoC6N(CH3)3Br, are quite different from the π-A isotherm of pure PLG on water subphase. In contrast to the case, the π-A isotherm of PLG mixed with nonionic C12AzoC6OPy is almost identical to the pure PLG except some increasing of molecular area. Similar phenomena are observed on DNA subphase. The in situ BAM and ex situ AFM observations demonstrate that the dispersion of PLG at air/water interface becomes good when it mixes with the two cationic surfactants, whereas quite poor due to the phase separation when it mixes with the nonionic amphiphilic molecule. Based on these results we conclude that the cationic surfactants can affect the conformation change of PLG at air/water interface and figure a well miscibility with polymer whereas the nonionic amphiphilic molecule presents poor miscibility. In addition, the even mixing of the PLG and the cationic surfactants is favorable for the adsorption to DNA more effectively.

Acid–organic base swollen polymer membranes

In this work, two different polymer membrane systems based on Nafion and Teflon were investigated as proton conductors for polymer membrane fuel cells. Water-free Nafion117 membranes swollen with different non-aqueous solvents were prepared. The solvents included imidazole, imidazole–imidazolium salt solutions, room temperature molten salts and molten salt–acid solutions. Teflon films were treated with a surfactant, or a Nafion solution, to improve their surface properties, and were subsequently swollen with phosphoric acid. Conductivity measurements were carried out on both the Nafion and Teflon membranes. Conductivities in the range of 10⁻³ S cm⁻¹ at around 100°C were obtained. This is still an order of magnitude lower than the corresponding water swollen Nafion at 80°C.

Solubilization of selected free fatty acids in palm oil by biodegradable ethoxylated surfactants

The solubilization of three major components, viz., palmitic, oleic, and linoleic acids, in palm oil by ethoxylated surfactants was investigated. The results were analyzed in terms of the molecular properties of surfactants and free fatty acids (FFAs). It was found that the solubilities of these FFAs in various micellar solutions depend not only on their octanol−water partition coefficients (Kow), but also on their physicochemical properties. The study on the solubilization kinetics was conducted by choosing palmitic acid as a model solubilizate and Tergitol 15-S-7 as the model surfactant. A first-order film diffusion model, which accounts for the direct uptake of organic molecules at a solid surface into surfactant micelles, was adopted to analyze the effect of surfactant on dissolution of palmitic acid. It was observed that the presence of surfactant reduced the mass-transfer coefficient. Instead, the overall mass-transfer rate was enhanced because of the much higher driving force from the increased solubilization capacity.

Controlling nanoparticle formation via sizable cages of supramolecular soft materials

We present a new generic strategy to fabricate nanoparticles in the “cages” within the fibrous networks of supramolecular soft materials. As the cages can be acquired by a design-and-production manner, the size of nanoparticles synthesized within the cages can be tuned accordingly. To implement this idea, both selenium and silver were chosen for the detailed investigation. It follows that the sizes of selenium and silver nanoparticles can be controlled by tuning the pore size of the fiber networks in the material. When the concentration of the gelator is high enough, monodisperse nanoparticles can be prepared. More interestingly, the morphology of the nanoparticles can be altered: silver disks can be formed when the concentrations of both the gelator and silver nitrate are sufficiently low. As the fiber network serves as a physical barrier and semisolid support for the nanoparticles, the stability in the aqueous media and the ease of application of these nanoparticles can be substantially enhanced. This robust surfactant-free approach will not only allow the controlled fabrication of nanoparticles, but also can be applied to the fabrication of composite materials for robust applications.