Refinement of retained austenite in super-bainitic steel by a deep cryogenic treatment

The effect of a deep cryogenic treatment on the microstructure of a super-bainitic steel was investigated. It was shown that quenching the super-bainitc steel in -196°C liquid nitrogen resulted in the transformation of retained austenite to two phases: ~20 nm thick martensite films and some nano carbides with a ~25 nm diameter. Some refinement of the retained austenite occurred, due to formation of fine martensite laths within the retained austenite. The evolution of these new phases resulted in an increase in the average hardness of the super-bainitic steel from 641 to ~670 HV1. © 2014 ISIJ.

Grain refinement in titanium alloys through thermomechanical processing

Qi developed a novel thermomechanical processing route for the grain refinement of titanium alloys. This leads to a well-balanced superior mechanical property, which is vital for modern air transport. The outcomes of this project are prospective to enhance titanium application and the long-term viability of Australian resources and manufacturing industries.

β-Ti grain refinement via α-Precipitation

The present work explores the impact of α precipitates on β recrystallization following hot deformation of Ti-5Al-5Mo-5V-3Cr with grains larger than 1 mm. A single hot rolling pass of 36 pct reduction was conducted on an aged microstructure containing α precipitates at a temperature well below the β transus temperature. After annealing, a uniformly recrystallized structure with a grain size of ~100 µm is formed. The prior β grain boundaries can be readily identified and it is seen that the primary β grains have been replaced by grains displaying a spread of correlated misorientation angles extending up to the highest allowable values. The annealing comprises two stages. The first stage involves normal β subgrain growth limited by the Zener pinning force of the unstable α precipitates. The second stage corresponds to the onset of β recrystallization at the point where the Zener pinning force drops due to dissolution of the α precipitates. This leads to a uniform distribution of site saturated recrystallization nuclei.

Refinement and validation of the Work Readiness Scale for graduate nurses.

The transition from student to registered nurse is often stressful and has been attributed to a lack of work readiness. Understanding what comprises work readiness for newly registered nurses, or graduate nurses as they are referred to in Australia, may reduce attrition and improve transition into the workplace. The 64-item Work Readiness Scale (WRS), developed with a generic population of graduates, has yet to be validated against specific disciplines to confirm applicability as a measure of work readiness. This study adapted the original WRS for use with a graduate nurse population (WRS-GN). The aim was to refine and validate the WRS-GN and determine whether the original four factor construct was supported. The WRS-GN was completed by 450 graduate nurses. Exploratory factor analyses supported the original four-factor solution (social intelligence, personal work characteristics, organizational acumen, and work competence). The final WRS-GN consisted of 46 items, showed excellent reliability, and explained 73.55% of the variance.

Texture evolution and grain refinement of ultrafine-grained copper during micro-extrusion

Samples of oxygen-free high conductivity (OFHC) coarse-grained (CG) and ultrafine-grained (UFG) copper were micro-extruded to an equivalent strain of 2.8 in one pass at room temperature. Samples of the OFHC copper were annealed at 650C for 2 h to produce CG copper. Some samples were subsequently processed by equal channel angular pressing of eight passes, route Bc, at room temperature to produce the UFG material. Crystallographic texture and misorientation distributions were obtained locally from EBSD mappings at different radial positions after micro-extrusion. To model the strain path during micro-extrusion, the analytic flow line model of Altan etal. [J Mater. Process. Tech. 33 (1992) p.263] was used and also validated by finite element calculations. Modelling was carried out using the viscoplastic self-consistent (VPSC) model and a recently developed grain refinement model. The results showed large texture variations along the cross-section of the extruded sample for both UFG and CG copper. These cyclic drawing textures in UFG copper were simulated in good agreement with experiments using the presented modelling framework.

Analysis of cultural conflict in the development of web-enabled information systems

The advent of the World Wide Web (WWW) and the emergence of Internet commerce have given rise to the web as a medium of information exchange. In recent years, the phenomenon has affected the realm of transaction processing systems, as organizations are moving from designing web pages for marketing purposes, to web-based applications that support business-to-business (WEB) and business-to-consumer (B2C) interactions, integrated with databases and other back-end systems (Isakowitz, Bieber et al., 1998). Furthermore, web-enabled applications are increasingly being used to facilitate transactions even between various business units within a single enterprise. Examples of some of the more popular web-enabled applications in use today include airline reservation systems, internet banking, student enrollment systems in universities, and Human Resource (HR) and payroll systems. The prime motive behind the adoption of web-enabled applications are productivity gains due to reduced processing time, decrease in the usage of paper-based documentation and conventional modes of communication (such as letters, fax, or telephone), and improved quality of services to clients. Indeed, web-based solutions are commonly referred to as customer-centric (Li, 2000), which means that they provide user interfaces that do not necessitate high level of computer proficiency. Thus, organizations implement such systems to streamline routine transactions and gain strategic benefits in the process (Nambisan & Wang, 1999), though the latter are to be expected in the long-term. Notwithstanding the benefits of web technology adoption, the web has ample share of challenges for initiators and developers. Many of these challenges are associated with the unique nature of web-enabled applications. Research in the area of web-enabled information systems has revealed several differences with traditional applications. These differences exist with regards to system development methodology, stakeholder involvement, tasks, and technology (Nazareth, 1998). According to Fraternali (1999), web applications are commonly developed using an evolutionary prototyping approach, whereby the simplified version of the application is deployed as a pilot first, in order to gather user feedback. Thus, web-enabled applications typically undergo continuous refinement and evolution (Ginige, 1998; Nazareth, 1998; Siau, 1998; Standing, 2001). Prototype-based development also leads web-enabled information systems to have much shorter development life cycles, but which, unlike traditional applications, are regrettably developed in a rather adhoc fashion (Carstensen & Vogelsang, 2001). However, the principal difference between the two kinds of applications lies in the broad and diverse group of stakeholders associated with web-based information systems (Gordijn, Akkermans, et al., 2000; Russo, 2000; Earl & Khan, 2001; Carter, 2002; Hasselbring, 2002; Standing, 2002; Stevens & Timbrell, 2002). Stakeholders, or organizational members participating in a common business process (Freeman, 1984), vary in their computer competency, business knowledge, language and culture. This diversity is capable of causing conflict between different stakeholder groups with regards to the establishment of system requirements (Pouloudi & Whitley, 1997; Stevens & Timbrell, 2002). Since, web-based systems transcend organizational, departmental, and even national boundaries, the issue of culture poses a significant challenge to the web systems’ initiators and developers (Miles & Snow, 1992; Kumar & van Dissel, 1996; Pouloudi & Whitley, 1996; Li & Williams, 1999).

Hot working microstructure map for magnesium AZ31

A thermomechanical processing (TMP) structure map is proposed that plots the critical strains required for dynamic recrystallization along with the grain sizes that result. These maps are useful in identifying the limits to grain refinement and designing hot working processes. They are readily constructed for well studied alloys such as plain carbon steel. In light of the recent interest in the hot working of magnesium, initial steps are taken here to construct a TMP structure map for the most common wrought magnesium alloy, AZ31. The completion of dynamic recrystallization is estimated using a geometrical approach and a twinning region is identified.

A window for a purpose: developing a framework for describing effective science teaching and learning

This paper describes the development of a framework – the SIS Components – for describing effective teaching and learning in science, to support a system wide change initiative. The methodology used and the analysis that led to their refinement, is traced to expose the different issues involved in constructing the notion of lsquoeffective practice.rsquo These issues have to do with purpose, politics and audience. They determine features of the framework such as specificity, elements focused on, and the support structures that are put in place to establish the particular discourse being promoted. The paper describes the different research methods used to establish, to promote and to validate the components, and outlines the different senses in which this and any framework can be seen as contingent on the setting for which it is intended.

Effect of deformation schedule on the microstructure and mechanical properties of a thermomechanically processed C-Mn-Si transformation-induced plasticity steel

Thermomechanical processing simulations were performed using a hot-torsion machine, in order to develop a comprehensive understanding of the effect of severe deformation in the recrystallized and nonrecrystallized austenite regions on the microstructural evolution and mechanical properties of the 0.2 wt pct C-1.55 wt pct Mn-1.5 wt pct Si transformation-induced plasticity (TRIP) steel. The deformation schedule affected all constituents (polygonal ferrite, bainite in different morphologies, retained austenite, and martensite) of the multiphased TRIP steel microstructure. The complex relationships between the volume fraction of the retained austenite, the morphology and distribution of all phases present in the microstructure, and the mechanical properties of TRIP steel were revealed. The bainite morphology had a more pronounced effect on the mechanical behavior than the refinement of the microstructure. The improvement of the mechanical properties of TRIP steel was achieved by variation of the volume fraction of the retained austenite rather than the overall refinement of the microstructure.

Microstructural evolution of ultrafine grained structure in plain carbon steels through single pass rolling

In the present study, the effect of nominal equivalent strain (between 0 and 1.2), deformation temperature (790– 750°C) and carbon content (0.06 – 0.35%C) was investigated on ferrite grain refinement through dynamic strain induced transformation (DSIT) in plain carbon steels in single pass rolling. The microstructural evolution of the transformation of austenite to ferrite has been evaluated through the thickness of the strip. The results showed a number of important microstructural features as a function of strain, which could be classified into three regions; no DSIT region, DSIT region, and ultrafine ferrite (UFF) grain region. Hence, two critical strains; dynamic strain induced transformation (εC, DSIT) and ultrafine ferrite formation (εC, UFF) were determined. These strains were increased significantly with an increase in carbon content. The critical strain for UFF formation reduced with decrease in deformation temperature. The UFF microstructure consisted of ultrafine, equiaxed ferrite grains (<2 μm) with very fine cementite particles. In the centre of the rolled strip, there was a conventional ferrite– pearlite microstructure, although ferrite grain refinement and the volume fraction of ferrite increased with increase in the nominal equivalent strain.

The static, dynamic and metadynamic recrystallisation of a medium carbon steel

Grain refinement during and after hot isothermal deformation of a medium carbon steel has been investigated. The average austenite grain size decreased with an increase in strain for the hot deformed and recrystallised material, with refinement extending beyond the strain for the peak stress. A window of strain that corresponds to transition from classical static to metadynamic recrystallisation was observed in respect to the recrystallised material. Within this post-dynamic transition window the strain at which strain independent softening occurs was different for different volume fractions of the recrystallised material. This led to a new terminology corresponding to initiation of strain independent softening. For the alloy of this study, strain independent softening for the start of post-deformation recrystallisation occurred near the strain to the peak stress. The strain corresponding to complete metadynamic recrystallisation, which was defined as when all levels of recrystallisation were strain independent, was much greater than the strain for the peak stress.

Formation of ultrafine grained structure in plain carbon steels through thermomechanical processing

In the present study, wedge-shaped samples were used to determine the effect of nominal equivalent strain (between 0 and 1.2) and carbon content (0.06--0.35%C) on ferrite grain refinement through dynamic strain-induced transformation (DSIT) in plain carbon steels using single-pass rolling. The microstructural evolution of the transformation of austenite to ferrite has been evaluated through the thickness of the strip. The results showed a number of important microstructural features as a function of strain which could be classified into three regions; no DSIT region, DSIT region and the ultrafine ferrite (UFF) grain region. Also, the extent of these regions was strongly influenced by the carbon content. The UFF microstructure consisted of ultrafine, equiaxed ferrite grains (<2 μ$m) with very fine cementite particles. In the centre of the rolled strip, there was a conventional ferrite-pearlite microstructure, although ferrite grain refinement and the volume fraction of ferrite increased with an increase in the nominal equivalent strain.

The static and metadynamic recrystallization behaviour of an X60 Nb Microalloyed Steel

A rapid method has been developed to determine recrystallization kinetics of Nb microalloyed steels by interrupted hot torsion test. The softening behaviour was achieved as a function of different processing parameters. The method clearly identified three regions, where the strain dependency of the recrystallization rate varied. Firstly, at large strains the rate of recrystallization was not a function of strain; this is generally ascribed to metadynamic recrystallization. At lower strains the time to 50% recrystallization showed a power low relationship with strain, characteristic of static recrystallization. A further break point exists on the time for 50% softening curve when strain induced precipitation occurs in the material. The onset of strain induced precipitation was at strains below the strain to the peak stress at temperatures below 900°C. The experimental results were used to estimate the time for 50% softening and to anticipate the onset of the strain induced precipitation for the alloy of this study. Grain refinement of the recrystallized austenite continued to strains significantly beyond the peak stress and beyond the static to metadynamic recrystallization rate transition.

Static and metadynamic recrystallization of interstitial free steels during hot deformation

A rapid method was used to identify kinetics of the recrystallization for two IF (Interstitial Free) steels which have different phosphorous and boron contents. The static and metadynamic softening behaviour of the materials for a range of strain rates and temperatures were quantified. The critical strain for initiation of strain independent softening was estimated for the IF steels in respect to the time for 50 percent softening after deformation. The results showed that the strain for the initiation of strain independent softening (often referred to as metadynamic recrystallization) varies with the Zener Hollomon parameter. Classic static recrystallization was observed at strains below the strain independent softening for all processing conditions and the strain rate had a strong effect on the time for strain independent softening. Results also revealed that static and metadynamic recrystallization was delayed owing to the phosphorous and boron alloying elements. Hence, the large strain at above no-recrystallization temperature may be required for the early stage of Finishing Stands Unit (FSU) in hot strip rolling mills to initiate austenite grain refinement of phosphorous and boron added IF steels.

DDR: an index method for large time-series datasets

The tree index structure is a traditional method for searching similar data in large datasets. It is based on the presupposition that most sub-trees are pruned in the searching process. As a result, the number of page accesses is reduced. However, time-series datasets generally have a very high dimensionality. Because of the so-called dimensionality curse, the pruning effectiveness is reduced in high dimensionality. Consequently, the tree index structure is not a suitable method for time-series datasets. In this paper, we propose a two-phase (filtering and refinement) method for searching time-series datasets. In the filtering step, a quantizing time-series is used to construct a compact file which is scanned for filtering out irrelevant. A small set of candidates is translated to the second step for refinement. In this step, we introduce an effective index compression method named grid-based datawise dimensionality reduction (DRR) which attempts to preserve the characteristics of the time-series. An experimental comparison with existing techniques demonstrates the utility of our approach.