Controlled growth of zinc nanowires

Zinc nanowires have been synthesized by heating a mixture of boron and zinc oxide (ZnO) powders at 1050 °C under a nitrogen atmosphere. The influences of the gas flow rate and the substrate character on the nanowire formation were investigated. It was found that higher-flow rate of gas led to the formation of thinner nanowires; while lower-flow rate of gas produced thicker nanowires and even particles due to the higher partial pressure of Zn vapor in this case. Zn nanowires can be produced on alumina and quartz substrates, but not on a stainless-steel substrate under the same or different synthetic conditions. Photoluminescence measurements were conducted on Zn nanowires and particles and weak emission bands at 482 and 493 nm were observed, which may be contributed by the thin ZnO film on the nanowire surface.

Tribology of lubricated nitrocarburised and titanium carbonitride surfaces

In the current work, two different coatings, nitrocarburised (CN) and titanium carbonitride (TiCN) on M2 grade high speed tool steel, were prepared by commercial diffusion and physical vapour deposition (PVD) techniques, respectively. Properties of the coating were characterised using a variety of techniques such as Glow-Discharge Optical Emission Spectrometry (GD-OES) and Scanning Electron Microscopy (SEM). Three non-commercial, oil-based lubricants with simplified formulations were used for this study. A tribological test was developed in which two nominally geometrically-identical crossed cylinders slide over each other under selected test conditions. This test was used to evaluate the effectiveness of a pre-applied lubricant film and a surface coating for various conditions of sliding wear. Engineered surface coatings can significantly improve wear resistance of the tool surface but their sliding wear performances strongly depend on the type of coating and lubricant combination used. These coating-lubricant interactions can also have a very strong effect on the useful life of the lubricant in a tribological system. Better performance of lubricants during the sliding wear testing was achieved hen used with the nitrocarburised (CN) coating. To understand the nature of the interactions and their possible effects on the coating-lubricant system, several surface analysis techniques were used. The molecular level investigation of Fourier Transform Infrared Spectroscopy (FTIR) revealed that oxidative degradation occurred in all used oil-based lubricants during the sliding wear test but the degradation behaviour of oil-based lubricants varied with the coating-lubricant system and the wear conditions. The main differences in the carbonyl oxidation region of the FTIR spectra (1900-1600 cm-1) between different coating-lubricant systems may relate to the effective lifetime of the lubricant during the sliding wear test. Secondary Ion Mass Spectrometry (SIMS) depth profiling shows that the CN coating has the highest lubricant absorbability among the tested tool surfaces. Diffusion of chlorine (C1), hydrogen (H) and oxygen (O) into the surface of subsurface of the tool suggested that strong interactions occurred between lubricant and tool surface during the sliding wear test. The possible effects of the interactions on the performance of whole tribological system are also discussed. The study of Time-of-Flight Secondary Ion Mass Spectrometry (TOF-SIMS) indicated that the envelope of hydrocarbons (CmHn) of oil lubricant in the positive TOF-SIMS spectra shifted to lower mass fragment after the sliding wear testing due to the breakage of long-chain hydrocarbons to short-chain ones during the degradation of lubricant. The shift of the mass fragment range of the hydrocarbon (CmHn) envelope caries with the type of both tool surface and lubricant, again confirming that variation in the performance of the tool-lubricant system relates to the changes in surface chemistry due to tribochemical interactions at the tool-lubricant interface under sliding wear conditions. The sliding wear conditions resulted in changes not only in topography of the tool surface due to mechanical interactions, as outlined in Chapter 5, but also in surface chemistry due to tribochemical interactions, as discussed in Chapters 6 and 7.

Synthesis and characterization of hexagonal and truncated hexagonal shaped MoO3 nanoplates

Hexagonal and truncated hexagonal shaped MoO₃ nanoplates (MoO₃ HNP) were synthesized through a simple vapor-deposition method in Ar atmosphere under ambient pressure without the assistant of any catalysts. The structure and morphology of MoO₃ HNP were investigated by XRD, EDX, SEM, TEM, and HRTEM. The results reveal that the HNP are α-MoO₃ and have a large area surface. The Raman spectrum shows a significant size effect on the vibrational property of MoO₃ HNP. The photoluminescence (PL) spectrum was carried out, and two peaks at 351 and 410 nm were observed in the spectrum. In addition, a possible growth mechanism proposed as VS is discussed in detail.

Corrosion properties of plasma-polymerized methylcyclohexane films using electrochemical methods

Three types of methylcyclohexane (MCH) coating were deposited as interlayer dielectrics on copper using plasma-enhanced chemical vapor deposition (PECVD) at three different RF plasma power levels. The coating performance was then evaluated by an electrochemical im pedance spectroscopy (EIS) and a potentiodynamic polarization test in 3.5 wt.% NaCl solution. An atomic force microscopy (AFM) and Fourier transform infrared reflection (FT-IR) spectroscopy were also conducted to analyze the coatings. The MCH coatings showed a lower corrosion rate than the copper substrate in the potentiodynamic tests. The EIS results showed that the corrosion resistance of the coatings increased with an increasing plasma power. Thus, the MCH films with an increasing plasma power improved the corrosion resistance due to the formation of a low-porosity coating, the enhanced formation of C−H, C−C, and C≡C stretching configurations, and the improved smooth surfaces.

Characterization and tribological performance of Cu-based intermetallic layers

Fluidized bed reactor chemical vapor deposition (FBR-CVD) has been used to enrich the surface of oxygen free high conductivity (OFHC) copper with titanium, silicon and aluminum. This technique enables the production of coherent and adherent intermetallic surface layers of uniform thickness and high hardness. The characterization of the coatings was performed using backscatter scanning electron microscopy (BS-SEM), X-ray diffraction (XRD), glow discharge optical emission spectroscopy (GDOES) and micro-hardness. The tribological properties of the coatings in dry sliding contact with steel were evaluated by pin-on-disc wear testing.

Heat reflective layered garment system

Heat-reflective layered apparel or footwear constructed from various combinations of layers of materials having selected thermal and moisture transfer properties to provide improved performance characteristics. Within these various combinations, the addition of a very thin heat reflective layer, made with a metallic material such as aluminum, applied using a vacuum plasma vapor deposition method, provides a coating that will reflect infra red heat energy either back to the body or away from the body. This heat reflective coating is so thin that is does not adversely alter the original suppporting fabrics hand feel, drape,weight , strectch or breathability. Various layers manage the body heat of an individual by reflection or thermal retention while also providing moisture wicking and antimicrobial function. Other layers manage thermal isolation from the external temperatures by using materials with very low thermal conductivity in combination with waterproof layers that can also be breathable.

Synthesis and characterization of tin dioxide core-shell structure nanowires

In this study, one-dimensional and quasi-one-dimensional tin dioxide nanowires and nan-owalls were fabricated by the use of the chemical vapor deposition technique. It was demonstrated that the growth and nanostructure of tin oxide can be controlled by varying the thickness of gold layer and the partial pressure of vapor at growing sites. Nanowires with a core-shell structure, i.e., pure tin core and tin oxide shell, were synthesized from C-S_nO₂ powders at a mol ratio of C/S_nO₂=3/5 on both silicon and Lanthanum Strontium Co-balt Ferrite ceramic wafers through the vapor-solid mechanism. The conditions that are favorable to the growth of core-shell structure nanowires are investigated.