Crystal structures and textures in the hot-forged Ni-Mn-Ga shape memory alloys

Three ferromagnetic shape-memory alloys with the chemical compositions of Ni₅₃Mn₂₅Ga₂₂, Ni₄₈Mn₃₀Ga₂₂, and Ni₄₈Mn₂₅Ga₂₂Co₅ were prepared by the induction-melting and hot-forging process. The crystal structures were investigated by the neutron powder diffraction technique, showing that Ni₅₃Mn₂₅Ga₂₂ and Ni₄₈Mn₂₅Ga₂₂Co₅ have a tetragonal, 14/mmm martensitic structure at room temperature, while Ni₄₈Mn₃₀Ga₂₂ has a cubic, L2₁ austenitic structure at room temperature. The development of textures in the hot-forged samples shows the in-plane plastic flow anisotropy from the measured pole figures by means of the neutron diffraction technique. Significant texture changes were observed for the Ni₄₈Mn₂₅Ga₂₂Co₅ alloy after room temperature deformation, which is due to the deformation-induced rearrangements of martensitic variants. An excellent shape-memory effect (SME) with a recovery ratio of 74 pct was reported in this Ni₄₈Mn₂₅Ga₂₂Co₅ polycrystalline alloy after annealing above the martensitic transformation temperature, and the “shape-memory” influence also occurs in the distributions of grain orientations.

Crystallographic features during martensitic transformation in Ni-Mn-Ga ferromagnetic shape memory alloys

The martensitic transformation crystallography in two Ni ₅₃Mn₂₅Ga₂₂ (at. %) ferromagnetic shape memory alloys (FSMAs) was investigated by means of misorientation calculation and pole figure analysis based on the orientation of the martensitic lamellae obtained from electron backscattered diffraction (EBSD) measurements. In the alloy that was first annealed at 1073K for 4h, and then cooled to 473K at ~4K/min and held for 30min, followed by cooling to room temperature at ~10K/min, there are only two kinds of differently orientated martensitic lamellae with a misorientation angle of ~82° distributed alternatively in each initial austenite grain. There is a compound twinning orientation relationship between the two lamellae. The prevalent orientation relationship between austenite and martensite is Kurdjumov-Sachs (K-S) relationship with (111)_A//(10I)_M, [1-10]_a//[11-1]_m. In the alloy that was annealed at 1173K for 4h followed by furnace cooling, nanoscale twins inside the martensitic lamellae were observed and the orientation relationships both between the nanotwins within one lamella and between the nanotwins in two neighboring lamellae were determined. The results presented in this paper will enrich the crystallographic data of the FSMAs and offer useful information for the development of novel FSMAs with optimal performances.

Determination of crystal structure and crystallographic characteristics in Ni-Mn-Ga ferromagnetic shape memory alloys

Ni-Mn-Ga ferromagnetic shape memory alloys (FSMAs) have received great attention during the past decade due to their giant magnetic shape memory effect and fast dynamic response. The crystal structure and crystallographic features of two Ni-Mn-Ga alloys were precisely determined in this study. Neutron diffraction measurements show that Ni48Mn30Ga22 has a Heusler austenitic structure at room temperature; its crystal structure changes into a seven-layered martensitic structure when cooled to 243K. Ni53Mn25Ga22 has an I4/mmm martensitic structure at room temperature. Electron backscattered diffraction (EBSD) analyses reveal that there are only two martensitic variants with a misorientation of ~82° around <110> axis in each initial austenite grain in Ni53Mn25Ga22. The investigation on crystal structure and crystallographic features will shed light on the development of high-performance FSMAs with optimal properties.

Mechanical properties and microstructure of powder metallurgy Ti-xNb-yMo alloys for implant materials

In this study, a series of Ti-xNb-yMo (x = 5-40 wt.% in 5 wt.% increments; and y = 3, 5, 10 wt%) alloys were fabricated by powder metallurgy and studied with respect to their microstructures, compressive mechanical properties and hardness. Increases in Nb and Mo content led to decreases in compressive and yield strengths, elastic modulus and hardness of the sintered alloys. Among the studied alloys, Ti-10Nb-3Mo alloy exhibited the optimum combination of strength and ductility. Alloys with a lower amount of Nb (≤ 25 wt.%) and Mo (≤ 5 wt.%) developed Widmanstätten structure, while further increase in Nb and Mo additions led to the microstructure predominantly consisting of β phase with varying regions of α + β phase. The effects of sintering temperature on elastic modulus and hardness were also investigated for Ti-xNb-3Mo alloys.

Preparation and characterisation of new titanium based alloys for orthopaedic and dental applications

Various types of titanium alloys with high strength and low elastic modulus and, at the same time, vanadium and aluminium free have been developed as surgical biomaterials in recent years. Moreover, porous metals are promising hard tissue implants in orthopaedic and dentistry, where they mimic the porous structure and the low elastic modulus of natural bone. In the present study, new biocompatible Ti-based alloy foams with approximate relative densities of 0.4, in which Sn and Nb were added as alloying metals, were synthesised through powder metallurgy method.
The new alloys were prepared by mechanical alloying and subsequently sintered at high temperature using a vacuum furnace. The characteristics and the processability of the ball milled powders and the new porous titanium-based alloys were characterised by X-ray diffraction, optical
microscopy and scanning electron microscopy .The mechanical properties of the new titanium alloys were examined by Vickers microhardness measurements and compression testing.

Comparative study on thermodynamical and electrochemical behavior of Al88Ni6La6 and Al86Ni6La6Cu2 amorphous alloys

Two amorphous ribbons with the compositions of Al₈₈Ni₆La₆ and Al₈₆Ni₆La₆Cu₂ were made using the meltspun method, and their thermal response and electrochemical behavior were studied comparatively. Differential scanning calorimetry (DSC) and electrochemical polarization measurements indicated that Al₈₆Ni₆La₆Cu₂ exhibited slightly higher crystallization temperature (T_x), lower melting point (T₁) and better corrosion resistance in 0.01 mol · L⁻¹ NaCl alkaline solution. These results demonstrated that Cu (2%) addition could slightly promote the glass forming ability, but it could greatly improve the corrosion resistance of Al₈₈Ni₆La₆ alloy in 0.01 mol · L⁻¹ NaCl alkaline solution.

Microstructure evolution of TI-SN-NB alloy prepared by mechanical alloying

In the present study, Ti-16Sn-4Nb alloy was prepared by mechanical alloying (MA). Optical microscopy, scanning electron microscopy combined with energy dispersive X-ray analysis (SEM-EDX), and X-ray diffraction analysis (XRD) were used to characterise the phase transformation and the microstructure evolution. Results indicated that ball milling to 8 h led to the formation of a supersaturated hcp α-Ti and partial amorphous phase due to the solid solution of Sn and Nb into Ti lattice. The microstructure of the bulk sintered Ti-16Sn-4Nb alloy samples made from the powders at shorter ball milling times, i.e. 20 min- 2 h, exhibited a primary α surrounded by a Widmanstätten structure (transformed β); while in the samples made from the powders at longer ball milling times, i.e. 5- 10 h, the alloy evolved to a microstructure with a disordered and fine β phase dispersed homogeneously within the α matrix. These results contribute to the understanding of the microstructure evolution in alloys of this type prepared by powder metallurgy.