Polymer coatings containing nano particles of zinc oxide for the UV protection of dyed polyester fabrics

The useful life of many outdoor textile products is limited by degradation caused by exposure to sunlight, in particular by the ultra violet component (below 400 nm). The degradation results in fading of colours and also loss of physical properties, such as tear strength and abrasion resistance. Degradation can be decreased with UV absorbers, often used in conjunction with antioxidants or free radical quenchers. The protection afforded by these organic compounds is, however, limited as they are ultimately destroyed by the UV radiation they absorb.
An alternative approach is to coat fabrics with a polymer containing an inorganic UV absorber, such as zinc oxide. The inherent stability of zinc oxide would be expected to provide a protective effect over a much longer period than can be achieved with an organic UV absorber. A possible disadvantage of zinc oxide when applied in a polymer film is that absorption and scattering of visible light can produce hazy films and, hence, an unacceptable change in fabric appearance.
This poster paper examines the possibility of using nano particles of zinc oxide dispersed in acrylic polymers for protecting dyed polyester fabrics against sunlight fading. Factors affecting both UV absorbance and film clarity will be discussed. The possibility will also be examined that the protective effect may be reduced in some circumstances by reactive oxygen species, generated by the interaction of UV with zinc oxide in the presence of air and water.

Development of a contact probe incorporating a bragg grating strain sensor for nano coordinate measuring machines

This paper presents a novel optical fibre based micro contact probe system with high sensitivity and repeatability. In this optical fibre probe with a fused spherical tip, a fibre Bragg grating has been utilized as a strain sensor in the probe stem. When the probe tip contacts the surface of the part, a strain will be induced along the probe stem and will produce a Bragg wavelength shift. The contact signal can be issued once the wavelength shift signal is produced and demodulated. With the fibre grating sensor element integrated into the probe directly, the probe system shows a high sensitivity. In this work, the strain distributions along the probe stem with the probe under axial and lateral load are analysed. A simulation of the strain distribution was performed using the finite element package ANSYS 11. Performance tests using a piezoelectric transducer stage with a displacement resolution of 1.5 nm yielded a measurement resolution of 60 nm under axial loading.

Dielectrophoresis for manipulation of micro/nano particles in microfluidic systems

Dielectrophoretic (DEP) force is exerted when a neutral particle is polarized in a non-uniform electric field, and depends on the dielectric properties of the particle and the suspending medium. The integration of DEP and microfluidic systems offers numerous applications for the separation, trapping, assembling, transportation, and characterization of micro/nano particles. This article reviews the applications of DEP forces in microfluidic systems. It presents the theory of dielectrophoresis, different configurations, and the applications of such systems for particle manipulation and device fabrication.

Enhancement of ion dynamics in PMMA-based gels with addition of TiO2 nano-particles

Solvent and ion dynamics in PMMA based gels have been investigated as a function of the loading of nanosized TiO₂ particles. The gels have a molar ratio of 46.5:19:4.5:30 of ethylene carbonate (EC), propylene carbonate (PC), lithium perchlorate and PMMA, respectively. A series of samples with 0, 4, 6 and 8 wt.% TiO₂ filler were investigated. The diffusion coefficients for the lithium ions and for the two solvents (EC and PC) were investigated by pfg-NMR. It was shown that the addition of filler to the gel electrolytes enhances the diffusion of the cations, while the diffusion of the solvents remains constant. Raman measurements show no significant changes in ion–ion interactions with the addition of fillers, while the ionic conductivity is seen to decrease. However, the sample with 8 wt.% TiO₂ had a conductivity close to that of the unfilled sample.

The 'filler-effect' in organic ionic plastic crystals : Enhanced conductivity by the addition of nano-sized TiO2

The addition of nano-sized ceramic particles to the plastic crystal ethyl-methyl pyrrolidinium bis(trifluoromethane sulfonyl)amide (P₁₂TFSA) has been investigated by means of DSC and conductivity. The thermal behaviour of the plastic crystal as a function of filler content suggests that the filler particles decrease the onset temperature of the melting slightly at high loadings, however they do not decrease the crystallinity of the material. Furthermore, the IV → III transition decreases in intensity, indicating that the addition of filler increases the possibility for the crystal to remain in metastable rotator phases also at lower temperatures. The conductivity shows a more than one order of magnitude increase with the addition of filler, with a filler concentration dependence that levels out above ~ 10 wt.% TiO₂.

The enhancement of lithium ion dissociation in polyelectrolyte gels on the addition of ceramic nano-fillers

Nano-particle oxide fillers including TiO₂, SiO₂ and Al₂O₃ have previously been shown to have a significant affect on the properties of both polymer and polymer gel electrolytes. In some cases, conductivity increases of one order of magnitude have been reported in crystalline PEO–base complexes. In this work, we report the effects of TiO₂ and SiO₂ on a poly(Li-AMPS)-based gel polyelectrolyte. Impedance spectroscopy and pfg-NMR spectroscopy indicates an increase in the number of available charge carriers with the addition of filler. An ideal amount of ceramic filler has been identified, with additional filler only saturating the system and reducing the conductivity below that of the pristine polyelectrolyte system. SEM micrographs suggest a model whereby the filler interacts readily with the sulfonate group; the surface area of the filler being an important factor.

The additive effect of zwitterion and nano-particles on ion dissociation in polyelectrolytes

To realise the battery potential of gel polyelectrolytes greater ion dissociation, ultimately leading to higher conductivities, must be achieved. Higher conductivities will result through increasing the ion-dissociating properties of the gel polyelectrolyte. The poor degree of ion dissociation arises as the active ion tends to remain in close proximity to the backbone charge. Nano-particle inorganic oxides, and zwitterionic compounds have been shown to act as dissociation enhancers in certain polyelectrolyte systems. In an attempt to further increase ion dissociation the addition of both TiO₂ nano-particles and a zwitterionic compound based on 1-butylimidazolium-3-N-(butanesulphonate) were added to the gel polyelectrolyte system poly (Li-2-acrylamido-2-methyl-1-propane sulphonate-co-N,N′-dimethylacrylamide), poly(Li-AMPS-co-DMAA) to determine if a synergistic effect occurs. Two different solvents were used to determine the breadth of applicability of the additive effect. The use of both dissociators resulted in the maximum ionic conductivity being achieved at lower nano-particle concentrations when compared to an identical system without zwitterion.

The effect of nano-particle TiO2 fillers on structure and transport in polymer electrolytes

Nano-particle oxide fillers including TiO₂, SiO₂ and Al₂O₃ have previously been shown to have a significant affect on the properties of polymer electrolytes, especially those based on polyether–lithium salt systems. In some cases, conductivity increases of more than one order of magnitude have been reported in crystalline PEO-based complexes. In this work, we report on the effects of TiO₂ on a completely amorphous polyether-based system to remove the complication of multiple phases presented by the semi-crystalline nature of PEO. Multinuclear magnetic resonance spectroscopy has shown that the lithium ion environment is changed by the addition of filler. Vibrational spectroscopy shows that the filler influences the disordered-longitudinal acoustic modes (DLAM) in the case of an amorphous polyether and suggests an interaction between the filler surface and the polymer. Positron annihilation lifetime spectroscopy indicates an increase in free volume upon addition of filler to an amorphous polyether–salt complex, coinciding with an apparent increase in polymer mobility as determined from ¹H T₂ NMR measurements. Impedance spectroscopy has shown clear evidence of an inter-phase region that may be more or less conductive than the bulk polymer electrolyte itself. The data support a model which includes conduction through an interfacial region in addition to the bulk polymer

Gel electrolytes based on lithium modified silica nano-particles

In this work lithium modified silica (Li-SiO₂) nano-particles were synthesized and used as a single ion lithium conductor source in gel electrolytes. It was found that Li-SiO₂ exhibited good compatibility with DMSO, DMA/EC (a mixture of N,N-dimethyl acetamide and ethylene carbonate) and the ionic liquid, N-methyl-N-propyl pyrrolidinium bis(trifluoromethylsulfonyl) amide ([C₃mpyr][NTf₂]). Several gel electrolytes based on Li-SiO₂ were obtained. These gel electrolytes were investigated by DSC, solid state NMR, conductivity measurements and cyclic voltammetry. Conductivities as high as 10⁻³ S/cm at room temperature were observed in these nano-particle gel electrolytes. The results of electrochemical tests showed that some of these materials were promising for using as lithium conductive electrolytes in electrochemical devices, with high lithium cycling efficiency evident.

Visible transparent, UV-blocking polymer nanocomposite films containing nano-sized organic-LDH (Layered Double Hydroxide) hybrid

A nano-sized Mg2Al layered double hydroxide (LDH) was used for encapsulating an organic UV absorber, 2-hydroxy-4- methoxybenzeophenone-5-sulfonic acid (HMBS), to produce HMBS@LDH hybrid nano-platelets. Upon dispersing this organic-inorganic hybrid LDH into ethylene-vinyl alcohol copolymer (EVOH) for film casting, a thin polymer
nanocomposite film that is UV opaque but highly transparent to visible light (higher than 90%) was formed. Thermogravimetry (TG) analysis confirmed that the intercalation of HMBS into LDH considerably increased the thermal stability of HMBS. Such an improvement was attributed to the strong guest-host interaction between the HMBS anions and the LDH layers. Also, the nanocomposite films were flexible and had good mechanical properties.

In vitro osteoblast-like cell proliferation on nano-hydroxyapatite coatings with different morphologies on a titanium-niobium shape memory alloy

The morphology of nanomaterials significantly affects their physical, chemical, and biological properties. In the present study, nano-hydroxyapatite coatings with different morphologies were produced on the surface of a titanium-niobium shape memory alloy via a hydrothermal process. The effect of the nano-hydroxyapatite coatings on the in vitro proliferation of SaOS-2 osteoblast-like cells was investigated. Factors including crystallinity, surface micro-roughness, and surface energy of the nano-hydroxyapatite coatings were discussed. Results show that in vitro proliferation of the osteoblast-like cells was significantly enhanced on the nano-hydroxyapatite-coated titanium-niobium alloy compared to the titanium-niobium alloy without coating. The cell numbers on the nano-hydroxyapatite-coated titanium-niobium alloy changed consistently with the surface energy of the hydroxyapatite coatings. This study suggests that surface energy as a characteristic parameter influencing the in vitro proliferation of osteoblast-like cells was predominant over the crystallinity and surface micro-roughness of the nano-hydroxyapatite coatings.

Nano-scale analysis of nano-bainite formed in advanced high strength steels

The effect of composition and processing schedule on the microstructure of C-Mn-Si-Mo-(Al)-(Nb) steels containing nano-bainite was studied using transmission electron microscopy (TEM) and atom probe tomography (APT). The major phase formed in all steels was nano-bainite. However, the steels with lower carbon and alloying addition content subjected to TMP had better mechanical properties than high alloyed steel after isothermal treatment. The presence of ferrite in the microstructure can improve not only ductility but lead to the formation of retained austenite with optimum chemical stability.

Effect of nano-Al2O3 addition on the densification of YSZ electrolytes

This work investigates the effect of nanosized Al2O3 addition on the sinterability of YSZ electrolyte. (1-x)YSZ + Al2O3 ceramics with compositions x = 0 to 0.01 were prepared by the conventional mixed oxide route from a commercial powder suspension (particle size <50 nm), and sintered at 1200 to 1500 degrees C for 2 hours in air. Densification, phase evolution, and microstructure were characterized by SEM/EDS and XRD. An improvement in sintered density was observed for the samples with 0.2 to 0.5 mol% Al2O3, though depending on the sintering temperature. Only cubic zirconia was detected as crystalline phase, although XRD features suggested chemical interactions depending upon the amount of Al2O3. The grain size of YSZ was homogeneous and no second phase segregation was detected in the tested range of incorporated nano-Al2O3 and sintering temperatures.

Architecture and engineering of a supramolecular functional material by manipulating the nano-structure of fiber network

Three-dimensional fiber networks were created from an organogel system consisting mainly of elongated fibrils by using a nonionic surfactant as an additive. The presence of the surfactant molecules manipulates the network structure by enhancing the mismatch nucleation on the growing fiber tips. Both the fiber network structure and the rheological properties of the material can be finely tuned by changing the surfactant concentration, which provides a robust approach to the engineering of supramolecular soft functional materials.