Effects of zirconium and strontium on the biocorrosion of Mg-Zr-Sr alloys for biodegradable implant applications

The successful applications of magnesium (Mg) alloys as biodegradable orthopedic implants are mainly restricted due to their rapid degradation rate in the physiological environment, leading to a loss of mechanical integrity. This study systematically investigated the degradation behaviors of novel Mg-Zr-Sr alloys using electrochemical techniques, hydrogen evolution, and weight loss in simulated body fluid (SBF). The microstructure and degradation behaviors of the alloys were characterized using optical microscopy, XRD, SEM, and EDX. The results indicate that Zr and Sr concentrations in Mg alloys strongly affected the degradation rate of the alloys in SBF. A high concentration of 5 wt% Zr led to acceleration of anodic dissolution, which significantly decreased the biocorrosion resistance of the alloys and their biocompatibility. A high volume fraction of Mg17Sr2 phases due to the addition of excessive Sr (over 5 wt%) resulted in enhanced galvanic effects between the Mg matrix and Mg17Sr2 phases, which reduced the biocorrosion resistance. The average Sr release rate is approximately 0.15 mg L^-1 day^-1, which is much lower than the body burden and proves its good biocompatibility. A new biocorrosion model has been established to illustrate the degradation of alloys and the formation of degradation products on the surface of the alloys. It can be concluded that the optimal concentration of Zr and Sr is less than 2 wt% for as-cast Mg-Zr-Sr alloys used as biodegradable orthopedic implants.

Enhanced ductility and reduced asymmetry of Mg-2Al-1Zn alloy plate processed by torsion and annealing

The ductility and plastic asymmetry of an as-annealed magnesium alloy plate were studied in compression through combined process of torsion and subsequent annealing by optical microscope and EBSD. The yield strength (YS) and ultimate compression strength (UCS) as well as the compression ductility (CD) were simultaneously raised by prior torsion at room temperature. The CD was further enhanced by subsequent annealing. Also, the torqued sample followed by annealing experienced a rising CD with the increase in prior strain, leading to the maximum true strain of 0.279, which is twice that of the as-annealed original one. The sample showed a largely reduced tension-compression yield asymmetry by subjecting to pre-torsion alone or combined with a subsequent annealing. The enhanced ductility and reduced asymmetry are attributed to the development of a gradient microstructure with refined grains, and also randomization of the weakened texture due to torsion and subsequent annealing.

Effects of Mg17Sr2 Phase on the bio-corrosion behavior of Mg-Zr-Sr alloys

The effect of the second phase Mg17Sr2 on the biocorrosion behavior of Mg5ZrxSr (x = 0, 2, 5 wt%) alloys before and after solution treatment was investigated. Electrochemical impedance spectroscopy, cathodic polarization and hydrogen evolution were used to evaluate the biocorrosion of Mg5ZrxSr. We found that Mg17Sr2 precipitated on boundary zones and enhanced the galvanic effect, leading to a severer corrosion of the Mg matrix adjacent to Mg17Sr2. The corrosion subsequently spread gradually from the regions adjacent to the Mg17Sr2 to the central Mg matrix. However, a high volume fraction of Mg17Sr2 could also form a continuous network, isolate the Mg matrix and act as a barrier of corrosion.

A Mg-Al-Nd alloy produced via a powder metallurgical route

A Mg-5 wt.%Al-2 wt.%Nd alloy has been prepared by a powder metallurgical route using a blend of two dissimilar alloy powders. The initial consolidation of the powders was achieved through a single equal channel angular extrusion pass at 150 °C. After heat treatment at temperatures between 420 °C and 530 °C, it was possible to produce a microstructure that consisted of a uniform distribution of Al3Nd and Al11Nd3 precipitates in a magnesium matrix. These precipitates displayed distinct orientation relationships with the matrix. The size and shape of the precipitates depended on the heat treatment temperature and time. © 2009 Elsevier B.V. All rights reserved.

Biodegradable Mg-Ca and Mg-Ca-Y alloys for regenerative medicine

In this study, Mg-xCa (x = 0.5, 1.0, 2.0, 5.0, 10.0, 15.0 and 20.0 %, wt.%, hereafter) and Mg-1Ca-1Y alloys were investigated as new biodegradable bone implant materials. The compressive strength, ultimate strength and hardness of the Mg-Ca alloys increased, whilst the corrosion rate and biocompatibility decreased, with the increase of the Ca content in the Mg-Ca alloys; higher Ca content caused the Mg-Ca alloy to become brittle. Solutions of simulated body fluid (SBF) and modified minimum essential media (MMEM) with the immersion of Mg-xCa and Mg-1Ca-1Y alloys showed strong alkalisation. The yttrium addition to the Mg-Ca alloys does not improve the corrosion resistance of the Mg-1Ca-1Y alloy as expected compared to the Mg-1Ca alloy. It is suggested that Mg-Ca alloys with Ca additions less than 1.0 wt.% exhibited good biocompatibility and low corrosion rate.

Control of biodegradation of a Mg alloy in simulated body fluid

Mg alloy AZ31 is an attractive candidate for coronary artery stents, as it possesses excellent biocompatibility in human body and good mechanical properties. However, AZ31 magnesium alloys generally have poor corrosion resistance in the body environment. This paper reports on the early stages of an investigation into the corrosion mechanism and the morphology of corrosion of AZ31 in simulated body fluid (SBF). The investigation will also consider ways of improving corrosion resistance of this alloy in SBF through the use of ionic liquids. The results to date have shown that AZ31 suffers severe localized pitting corrosion in SBF. The pits mainly develop adjacent to the Al-Mn intermetallic second phase in the α matrix. Energy Dispersive X-Ray Spectroscopy results revealed the presence of Mg, O, Ca, and P in the layer of corrosion product. Treatment of the AZ31 alloy prior to corrosion testing in SBF with the ionic liquid trimethyl (butyl) phosphonium diphenyl phosphate (P1444DPP) produced some increase in the corrosion resistance of the alloy.

Slip during tension testing of Mg-3A1-1Zn sheet

The activation of slip and twinning deformation modes in Mg-3Al-1Zn alloy was investigated by means of both in-situ and ex-situ methods at ambient temperature using electron back scattering diffraction (EBSD). The results confirm the importance of non-basal slip and c-axis compression double twinning. During tensile deformation of rolled sheet, 63% of the observed slip traces were ascribed to prismatic slip, 33% to basal slip and 4% to <c+a> slip. Prismatic slip was frequently observed in grain interiors. The density of twinning was quantified in samples tested along transverse, extrusion and rolling directions at failure. The values in the range of 0.02-0.18 twins per square micron were found depending on sample orientation. The results show the effect of twinning on failure.

Enhancement of properties in cast Mg-Y-Zn rod processed by severe plastic deformation

Ternary Mg-Y-Zn alloys have attracted considerable attention from researchers due to their excellent mechanical properties and unique microstructures, particularly from the presence of long-period stacking-order (LPSO) phases. Microstructural variations and the resulting mechanical properties can be affected by various processing routes, particularly those involving severe plastic deformation of a cast billet. The approach used in this work was based on subjecting cast Mg92Y4Zn4 (composition in wt%) billet to severe plastic deformation by three different routes, namely equal channel angular pressing (ECAP), high pressure torsion (HPT) and ECAP followed by HPT, with the aim of refining the microstructure and improving mechanical properties. Samples processed by ECAP were annealed by post-processing and tested in compression and tension. The effect of the processing route and the process parameters on the microstructure and the hardness of the Mg-Y-Zn alloy is reported. An overall positive effect of annealing treatment on the mechanical properties of ECAP-processed alloy is demonstrated. © 2014 Elsevier B.V.

Texture and mechanical anisotropy in three extruded magnesium alloys

One ZM61 alloy (6·2%Zn, 1·2%Mn) and two magnesium alloys containing nominally 3% of neodymium and yttrium respectively have been prepared in the form of hot extruded flat strips. Their textures and microstructures have been quantified and series of mechanical tests were carried out to determine plane stress yield loci in both the solution treated and aged conditions. The ZM61 alloy had a sharp texture and marked anisotropy of strength that could be rationalised in terms of deformation by basal <a> slip and {1012}<1011> twinning. This material was much weaker in compression than in tension. Precipitation hardening on aging caused a greater impedance to twinning than to slip with the result that the anisotropy was somewhat reduced. The Mg–3Nd alloy had a very weak and different texture but nevertheless demonstrated a pronounced anisotropy of strength. Aging increased the yield stress by about 80% and also inhibited twinning to some extent although the degree of anisotropy remained almost unaffected. The Mg–3Y alloy which showed a texture of intermediate strength was different in type from either of the others. Its strength behaviour was close to isotropic; in particular, no difference existed between tensile and compressive loading, and aging produced only a marginal increase in strength. Twins were relatively infrequent in the deformed Mg–3Y alloy but its mechanical behaviour could not be rationalised according to simple models.

Zirconium, calcium, and strontium contents in magnesium based biodegradable alloys modulate the efficiency of implant-induced osseointegration

Development of new biodegradable implants and devices is necessary to meet the increasing needs of regenerative orthopedic procedures. An important consideration while formulating new implant materials is that they should physicochemically and biologically mimic bone-like properties. In earlier studies, we have developed and characterized magnesium based biodegradable alloys, in particular magnesium-zirconium (Mg-Zr) alloys. Here we have reported the biological properties of four Mg-Zr alloys containing different quantities of strontium or calcium. The alloys were implanted in small cavities made in femur bones of New Zealand White rabbits, and the quantitative and qualitative assessments of newly induced bone tissue were carried out. A total of 30 experimental animals, three for each implant type, were studied, and bone induction was assessed by histological, immunohistochemical and radiological methods; cavities in the femurs with no implants and observed for the same period of time were kept as controls. Our results showed that Mg-Zr alloys containing appropriate quantities of strontium were more efficient in inducing good quality mineralized bone than other alloys. Our results have been discussed in the context of physicochemical and biological properties of the alloys, and they could be very useful in determining the nature of future generations of biodegradable orthopedic implants.

Strontium content and collagen-I coating of magnesium-zirconia-strontium implants influence osteogenesis and bone resorption.

Our objective was to study the role of Collagen type-I (Col-I) coating on Magnesium-Zirconia (Mg-Zr) alloys, containing different quantities of Strontium (Sr), in enhancing the in vitro bioactivity and in vivo bone-forming and mineralisation properties of the implants.

Biocompatible magnesium alloys for hard tissue engineering

 Novel Mg-Zr-Sr and Mg-1Zr-2Sr-xDy/yHo alloys have recently been developed for use as biodegradable implant materials. These alloys are recommended to be promising biodegradable implant materials as they have enhanced corrosion resistance and excellent biocompatibility.

Effect of increasing dietary calcium through supplements and dairy food on body weight and body composition: a meta-analysis of randomised controlled trials

This meta-analysis of randomised controlled trials assessed the effect of Ca on body weight and body composition through supplementation or increasing dairy food intake. Forty-one studies met the inclusion criteria (including fifty-one trial arms; thirty-one with dairy foods (n 2091), twenty with Ca supplements (n 2711). Ca intake was approximately 900 mg/d higher in the supplement groups compared with control. In the dairy group, Ca intake was approximately 1300 mg/d. Ca supplementation did not significantly affect body weight (mean change ( - 0·17, 95 % CI - 0·70, 0·37) kg) or body fat (mean change ( - 0·19, 95 % CI - 0·51, 0·13) kg) compared to control. Similarly, increased dairy food intake did not affect body weight ( - 0·06, 95 % CI - 0·54, 0·43) kg or body fat change ( - 0·36, 95 % CI - 0·80, 0·09) kg compared to control. Sub-analyses revealed that dairy supplementation resulted in no change in body weight (nineteen studies, n 1010) ( - 0·32, 95 % CI - 0·93, 0·30 kg, P= 0·31), but a greater reduction in body fat (thirteen studies, n 564) ( - 0·96, 95 % CI - 1·46, - 0·46 kg, P < 0·001) in the presence of energy restriction over a mean of 4 months compared to control. Increasing dietary Ca intake by 900 mg/d as supplements or increasing dairy intake to approximately 3 servings daily (approximately 1300 mg of Ca/d) is not an effective weight reduction strategy in adults. There is, however, an indication that approximately 3 servings of dairy may facilitate fat loss on weight reduction diets in the short term.

Investigation of precipitate hardening of slip and twinning in Mg5%Zn by micropillar compression

A Mg-5%Zn alloy has been aged to form c-axis rod precipitates which are known to increase strength. Micropillar compression tests were carried out in the precipitate-free and aged samples to investigate the effects of these precipitates on twinning and slip in magnesium alloys. Basal slip, pyramidal slip and {101¯2} twinning were selectively activated by compressing micropillars in the [112¯3], [0 0 0 1] and [112¯0] orientations, respectively. It has been found that precipitation causes moderate hardening of the basal slip system, and also significantly increases the work hardening rate. The compression of [112¯0] initiated twinning, but the present experiments were dominated by twin nucleation, rather than growth. It was found that the effect of precipitation on twin nucleation was negligible. Precipitation had little effect on specimens compressed in the c-axis.

Structure and mechanical property variations in Mg-Gd-Y-Zn-Zr alloy depending on its composition and processing conditions

An effect of alloying element content on mechanical properties and precipitate formation in Mg-RE alloys was studied for Mg-8Gd-4Y- 1Zn-0.4Zr (wt%) and Mg-10Gd-5Y-1.8Zn-0.4Zr (wt%). It is shown that small variations in the alloying element concentration can be used to manipulate the alloy microstructure and precipitate formation towards eliminating the asymmetry (tension/compression) and anisotropy of yield stress.