Texture changes during uniaxial compression of Mg-3AI-1Zn

The mechanical anisotropy of wrought Mg alloys is very high. For example the yield stress of extruded Mg-3Al-1Zn tested in tension can be as high as twice that obtained in compression [1]. To solve the problems this creates for product design it is necessary to understand the sensitivity of texture to processing parameters. Uniaxial compression tests at different temperatures were performed on cylindrical samples of an extruded Mg-3Al-1Zn bar. The texture
during this deformation changes from a situation where all crystal c-axes are nearly perpendicular to the sample axis to one where the c-axes are all nearly parallel to this axis. Compression was stopped at different strains to examine the rate of this texture change. Textures were examined using EBSD measurements. It was found that different mechanisms operate depending on the temperature of deformation and that a variety of textures can be created. Also it was seen that an annealing treatment performed after compression has an influence on the texture. Afterwards the samples were subjected to another uniaxial compression test to examine the influence of texture on room temperature properties.

Grain refinement of pure magnesium using rolled Zirmax® master alloy (MG-33.3ZR)

Owing to the limited solubility of zirconium in molten magnesium, almost all of the zirconium contained in the Zirmax® master alloy (Mg-33.3Zr) is present in the form of nearly pure zirconium particles. Of them, zirconium particle clusters and individual zirconium particles greater than 5

Slip during tension testing of Mg-3A1-1Zn sheet

The activation of slip and twinning deformation modes in Mg-3Al-1Zn alloy was investigated by means of both in-situ and ex-situ methods at ambient temperature using electron back scattering diffraction (EBSD). The results confirm the importance of non-basal slip and c-axis compression double twinning. During tensile deformation of rolled sheet, 63% of the observed slip traces were ascribed to prismatic slip, 33% to basal slip and 4% to <c+a> slip. Prismatic slip was frequently observed in grain interiors. The density of twinning was quantified in samples tested along transverse, extrusion and rolling directions at failure. The values in the range of 0.02-0.18 twins per square micron were found depending on sample orientation. The results show the effect of twinning on failure.

Effect of composition on the texture and deformation behaviour of wrought Mg alloys

The microstructure and mechanical response of three extruded magnesium alloys, Mg-3Al-1Zn (AZ31), Mg-1.5Mn (Ml) and Mg-lMn-0.4RE (ME10) are examined. The tensile yield strength of ME10 was nearly half that of AZ31 and Ml. The tensile elongations were 6%, 11% and 19% for Ml, AZ31 and ME10, respectively. This range of properties is large and is attributed to the unique extrusion texture produced in ME10, and the high density of fine particles in Ml.

The origin of "Rare Earth" texture development in extruded Mg-based alloys and its effect on tensile ductility

The extrusion behaviour, texture and tensile ductility of five binary Mg-based alloys have been examined and compared to pure Mg. The five alloying additions examined were Al, Sn, Ca, La and Gd. When these alloys are compared at equivalent grain size, the La- and Gd-containing alloys show the best ductilities. This has been attributed to a weaker extrusion texture. These two alloying additions, La and Gd, were found to also produce a new texture peak with View the MathML source parallel to the extrusion direction. This “rare earth texture” component was found to be suppressed at high extrusion temperatures. It is proposed that the View the MathML source texture component arises from oriented nucleation at shear bands.

Necking and failure at low strains in a coarse-grained wrought Mg alloy

Tensile testing of rolled AZ31 alloy with a mean grain size of 80 μm reveals localization and failure prior to diffuse necking. Optical microscopy reveals that failure is caused by voids that have formed within twins. A simple localization criterion is proposed that captures the role of grain size in the effect. Such early failure is only predicted for coarse grain sizes, in line with observation.

Characteristics of the contraction twins formed close to the fracture surface in Mg-3A1-1Zn alloy deformed in tension

Characteristics of the “contraction” twins, formed close to the fracture surface in Mg–3Al–1Zn alloy deformed in tension approximately perpendicular to the grain c-axes, are investigated using transmission electron microscopy. The grain c-axis contractions were largely accommodated by {1011}-{1012} source double-twins in a variant characterized by 38° ⟨1210⟩ source twin/matrix misorientation in conjunction with dislocation slip. A possible interpretation of the observed preference for this variant formation is given and some crystal plasticity modelling is performed to elucidate the matter.

Observation of {1121}twinning in a Mg-based alloy

The magnesium alloy Mg–5%Y–2%Nd–2%RE–0.5Zr, known as WE54, was heat treated to produce different particle dispersions. Specimens were then compressed to a strain of 8%, and this resulted in prolific mechanical twinning.EBSD analysis revealed that {1121} twins were operative in this alloy, a twinning mode not reported before in magnesium alloys. Activation of this twinning mode is ascribed to the presence of alloying elements in solution. Removal of alloying elements from solution by precipitation treatments completely inhibited this twin mode.

Investigation of deformation mechanisms involved in the plasticity of AZ31 Mg alloy: in situ neutron diffraction and EPSC modelling

In situ neutron diffraction and Elasto-Plastic Self-Consistent (EPSC) polycrystal modelling have been employed to investigate which deformation mechanisms are involved in the plasticity of extruded AZ31 Mg alloy during the tensile loading along the extrusion direction. On the basis of this study we were able to determine the relative activity of the slip and twinning deformation modes. By tuning the parameters of the EPSC model (i.e. the critical resolved shear strengths and hardening parameters), excellent agreement with the experimental data has been achieved. It is shown that the strain in the crystallographic ⟨c ⟩direction is accommodated mainly by ⟨c + a ⟩ dislocation slip on second-order pyramidal planes. The results further indicate that either slip of ⟨a ⟩dislocations occurs on {10.1} pyramidal planes or cross-slip from basal and prismatic planes takes place.

Tailoring the photocatalytic activity of nanoparticulate zinc oxide by transition metal oxide doping

The successful use of nanoparticulate ZnO in applications such as UV-screening agents or photocatalyst for the destruction of chemical waste requires the development of techniques for controlling its photocatalytic activity. In this study, we have investigated transition metal doping as a means of achieving this goal. Powders of ZnO, Mn_xZn_1−xO, and Co_xZn_1−xO were synthesised by a three-stage process consisting of high-energy mechanical milling, heat treatment, and washing. The photocatalytic activity of these powders was evaluated using the spin-trapping technique with electron paramagnetic resonance spectroscopy. It was found that the photocatalytic activity of Co_xZn_1−xO progressively decreased with the doping level. In contrast, the activity of Mn_xZn_1−xO initially increased with doping up to a level of 2 mol% and thereafter declined. These results demonstrate that doping with transition metal oxides can be used to tailor the photocatalytic properties of nanoparticulate ZnO.

Mg-based metallic glass / titanium interpenetrating phase composite with high mechanical performance

We report an Mg-based metallic glass/titanium interpenetrating phase composite in which constituent phases form a homogeneously interconnected network. The porous titanium constrains shear bands propagation thoroughly and promotes shear bands branching and intersection subsequently. The homogeneous phase distribution promotes regularly distributed local shear deformation and leads to a uniform deformation for the composites. Moreover, the interpenetrating phase structure introduces a mutual-reinforcement between metallic glass and titanium. Therefore, the composite exhibits excellent mechanical performance with compressive fracture strength of 1783 MPa and fracture strain of 31%.

Plastic flow properties and microstructural evolution in an ultrafine-grained Al-Mg-Si alloy at elevated temperatures

An AA6082 alloy was subjected to eight passes of equal channel angular pressing at 100 °C, resulting in an ultrafine grain size of 0.2 to 0.4 µm. The tensile deformation behavior of the material was studied over the temperature range of 100 °C to 350 °C and strain rate range of 10¯⁴ to 10¯¹ s¯¹. The evolution of microstructure under tensile deformation was investigated by analyzing both the deformation relief on the specimen surface and the dislocation structure. While extensive microshear banding was found at the lower temperatures of 100 °C to 150 °C, deformation at higher temperatures was characterized by cooperative grain boundary sliding and the development of a bimodal microstructure. Dislocation glide was identified as the main deformation mechanism within coarse grains, whereas no dislocation activity was apparent in the ultrafine grains.