Conductivity and NMR properties of plasticized polyethers complexed with lithium salts

NMR provides a tool whereby the dynamic properties of specific nuclei can be investigated. In the present study, a poly(ethylene oxide-co-propylene oxide) network has been used as the polymer host to prepare solid polymer electrolytes (SPE) containing either LiClO₄ or LiCF₃SO₃. In addition, a low molecular weight plasticizer [propylene carbonate (PC), dimethyl formamide (DMF) or tetraglyme] has been added to several of the samples to enhance the mobility of the polymer and, thus, of the ionic species. The effects of plasticizer and salt concentration on the ionic structure and mobility in these SPEs, as measured by NMR relaxation times, and correlation to the conductivity behaviour in these systems are discussed. Temperature dependent triflate diffusion coefficients, as measured by Pulsed Field Gradient ¹⁹F-NMR, in plasticized SPEs are also reported.

Lithium doped N-methyl-N-ethylpyrrolidiniumbis(trifluoromethanesulfonyl)amide fast-ion conducting plastic crystals

The incorporation of dopant levels of lithium ions (0.5 to 9.3% by mole) in the N-methyl-N-ethylpyrrolidinium bis(trifluoromethanesulfonyl)amide (P₁₂TFSA) plastic crystalline phase results in increases in the solid state ionic conductivity of more than 3 orders of magnitude at 298 K. Conductivities as high as 10^−-4 S cm⁻¹ at 323 K have been measured in these doped plastic crystal phases. These materials can therefore be classified as fast-ion conductors. Higher levels of Li only marginally increase the conductivity, up to around 33 mol%, followed by a slight decrease to 50 mol%. Thermal analysis behaviour has allowed the partial development of the binary phase diagram for the LiTFSA–P₁₂TFSA system between 0–50 mol% LiTFSA, which suggests the presence of a solid solution single phase at concentrations less than 9.3 mol% LiTFSA. There is also strong evidence of eutectic behaviour in this system with a eutectic transition temperature around 308 K at 33 mol% LiTFSA. A model relating ionic conduction to phase behaviour in this system is presented. The increased conductivity upon doping has been associated with lithium ion motion via⁷Li solid state NMR linewidth measurements.

NMR studies of modified nasicon-like, lithium conducting solid electrolytes*1

²⁷Al, ³¹P and ⁷Li NMR measurements have been performed on lithium conducting ceramics based on the LiTi₂(PO₄)₃ structure with Al, V and Nb metal ions substituted for either Ti or P within the framework NASICON structure. The ²⁷Al magic angle spinning NMR measurements have revealed that, although Al is intended to substitute for octahedral Ti sites, additional substitution into tetrahedral environments (presumably phosphorous sites) occurs with increasing amount of Al addition. This tetrahedral substitution appears to occur more readily in the presence of vanadium, in Li_1+xAl_xTi_2−x(PO₄)_2.9(VO₄)_0.1, whereas similar niobium additions (in place of vanadium) appear to stifle tetrahedral substitution. ⁷Li static NMR spectra reveal quadrupolar structure with C_q approximately 42 kHz, largely independent of substitution. Measurement of the ⁷Li central transition linewidth at room temperature reveals a relatively mobile lithium species (300–900 Hz) with linewidth tending to decrease with Al substitution and increase with increasing V or Nb. This new structural information is discussed in the context of ionic conduction in these ceramics.

Solid state lithium ion conduction in pyrrolidinium imide–lithium imide salt mixtures

The properties of the binary salt system based on mixtures of methyl ethyl pyrrolidinium bis(trifluoromethane sulfonyl) imide (P₁₂) and lithium bis(trifluoromethane sulfonyl) imide (Li imide) are reported. The lithium containing mixtures were found to be more than two orders of magnitude more conductive than the parent P₁₂ phase and the 33 mol% Li imide systems showed a solid state conductivity around 1×10⁻⁴ S/cm at 20°C. This solid state conductivity is believed to take place in plastic crystal phases of the P₁₂ compound.

Cycling performance of lithium metal polymer cells assembled with ionic liquid and poly(3-methyl thiophene)/carbon nanotube composite cathode

A poly(3-methylthiophene) (PMT)/multi-walled carbon nanotube (CNT) composite is synthesized by in situ chemical polymerization. The PMT/CNT composite is used as an active cathode material in lithium metal polymer cells assembled with ionic liquid (IL) electrolytes. The IL electrolyte consists of 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIBF4) and LiBF4. A small amount of vinylene carbonate is added to the IL electrolyte to prevent the reductive decomposition of the imidazolium cation in EMIBF4. A porous poly(vinylidene fluoride-co-hexafluoropropylene) (P(VdF-co-HFP)) film is used as a polymer membrane for assembling the cells. Electrochemical properties of the PMT/CNT composite electrode in the IL electrolyte are evaluated and the effect of vinylene carbonate on the cycling performance of the lithium metal polymer cells is investigated. The cells assembled with a non-flammable IL electrolyte and a PMT/CNT composite cathode are promising candidates for high-voltage–power sources with enhanced safety.

Lithium-doped plastic crystal electrolytes exhibiting fast ion conduction for secondary batteries

Rechargeable lithium batteries have long been considered an attractive alternative power source for a wide variety of applications. Safety and stability1 concerns associated with solvent-based electrolytes has necessitated the use of lithium intercalation materials (rather than lithium metal) as anodes, which decreases the energy storage capacity per unit mass. The use of solid lithium ion conductors - based on glasses, ceramics or polymers - as the electrolyte would potentially improve the stability of a lithium metal anode while alleviating the safety concerns. Glasses and ceramics conduct via a fast ion mechanism, in which the lithium ions move within an essentially static framework. In contrast, the motion of ions in polymer systems is similar to that in solvent-based electrolytes - motion is mediated by the dynamics of the host polymer, thereby restricting the conductivity to relatively low values. Moreover, in the polymer systems, the motion of the lithium ions provides only a small fraction of the overall conductivity2, which results in severe concentration gradients during cell operation, causing premature failure3. Here we describe a class of materials, prepared by doping lithium ions into a plastic crystalline matrix, that exhibit fast lithium ion motion due to rotational disorder and the existence of vacancies in the lattice. The combination of possible structural variations of the plastic crystal matrix and conductivities as high as 2 3 1024 S cm21 at 60 8C make these materials very attractive for secondary battery applications.

Lithium-ion conducting ceramic/polyether composites

Composites of a lithium ion conducting ceramic with a lithium salt based polymer electrolyte matrix are described. Conductivity measurements as a function of the lithium ion conducting ceramic phase content in the composite show that there is a significant increase in conductivity at approximately 40 vol% of the ceramic. The room temperature conductivity above this ceramic content is enhanced by at least 100% over that of the polymer electrolyte phase alone. It is believed that this additional contribution is substantially lithium ion conduction. The major barrier to ion-motion in these materials appears to be the interface between the polymer and ceramic. This interfacial resistance is strongly moisture-sensitive.

Ceramic-polymer interface in composite electrolytes of lithium aluminium titanium phosphate and polyetherurethane polymer electrolyte

Composite electrolytes of the lithium-ion-conducting ceramic Li_1.3Al_0.3Ti_1.7(PO₄)₃ and polyetherurethane/lithium triflate polymer electrolyte have been prepared. Microscopy has shown that adhesion between the ceramic and polymer phases is poor, with gaps up to 1 μm at the interface. When dry, the composites are no more conductive than the pure polymer electrolyte. Exposing the samples to the vapour of solvents such as DMF, acetonitrile or water produces a significant increase in conductivity, over and beyond simple plasticization of the polymer. Pretreating the ceramic with a compatibilizing agent improves adhesion at the interface with the polymer, but decreases overall conductivity in the case investigated.

Solid state NMR characterization of lithium conducting ceramics

⁷Li solid state NMR has been used to characterize lithium aluminium titanium phosphate and lithium lanthanum titanate ceramics. Both materials have high ionic mobilities at room temperature and this is reflected in their static ⁷Li powder patterns. In the case of the phosphate based ceramic, a narrow Lorentzian peak is observed above 300 K, which narrows further with increasing temperature. The accompanying quadrupolar structure, with C_Q (quadrupolar coupling constant) ~ 40 kHz, suggests that the lithium ions are hopping rapidly between equivalent, high electric field gradient sites. The ²⁷Al and ³¹P magic angle spinning (MAS) spectra reveal an asymmetric phosphorus peak and two distinct aluminium resonances. The room temperature powder pattern of Li_0.33La_0.57TiO₃ shows a dipolar broadened peak which narrows quite suddenly at 310 K revealing quadrupolar satellites with C_Q ~ 900 Hz. A second lithium site is also observed in this material, as indicated by a further, weaker quadrupolar structure (C_Q ~ 40 kHz).

Surprising effect of nanoparticle inclusion on ion conductivity in a lithium doped organic ionic plastic crystal

Doping lithium bis(trifluoromethanesulfonyl)amide (Li[NTf₂]) into the N-ethyl,N′-methylpyrrolidinium bis(trifluoromethanesulfonyl)amide ([C₂mpyr][NTf₂]) plastic crystal material has previously indicated order of magnitude enhancements in ion transport and conductivity over pure [C₂mpyr][NTf₂]. Recently, conductivity enhancements in this ionic plastic crystal induced by SiO₂ nanoparticles have also been reported. In this work the inclusion of SiO₂ nanoparticles in Li ion doped [C₂mpyr][NTf₂] has been investigated over a wide temperature range by differential scanning calorimetry (DSC), impedance spectroscopy, positron annihilation lifetime spectroscopy (PALS), Raman spectroscopy, NMR spectroscopy and scanning electron microscopy (SEM). Solid state ¹H NMR indicates that the addition of the nanoparticles increases the mobility of the [C₂mpyr] cation and positron lifetime spectroscopy (PALS) measurements indicate an increase in mean defect size and defect concentration as a result of nanoparticle inclusion, especially with 10 wt% SiO₂. Thus, the substantial drop in ion conductivity observed for this doped nanocomposite material was surprising. This decrease is most likely due to the decrease in mobility of the [NTf₂] anion, possibly by its adsorption at the SiO₂/grain boundary interface and concomitant decrease in mobility of the Li ion.

Gel electrolytes based on lithium modified silica nano-particles

In this work lithium modified silica (Li-SiO₂) nano-particles were synthesized and used as a single ion lithium conductor source in gel electrolytes. It was found that Li-SiO₂ exhibited good compatibility with DMSO, DMA/EC (a mixture of N,N-dimethyl acetamide and ethylene carbonate) and the ionic liquid, N-methyl-N-propyl pyrrolidinium bis(trifluoromethylsulfonyl) amide ([C₃mpyr][NTf₂]). Several gel electrolytes based on Li-SiO₂ were obtained. These gel electrolytes were investigated by DSC, solid state NMR, conductivity measurements and cyclic voltammetry. Conductivities as high as 10⁻³ S/cm at room temperature were observed in these nano-particle gel electrolytes. The results of electrochemical tests showed that some of these materials were promising for using as lithium conductive electrolytes in electrochemical devices, with high lithium cycling efficiency evident.