Local Austenite grain size distribution in hot bar rolling of AISI 4135 Steel

In this paper, the local distribution of austenite grain size (AGS) was experimentally determined by conducting single round-oval and square-diamond pass hot bar rolling experiments of AISI4135 steel. The rolling experiments were carried out using the laboratory mill. The local distribution of AGS was also determined numerically. In order to predict AGS distribution, the AGS evolution model was combined with three dimensional non-isothermal finite element analyses by adopting a modified additivity rule. AGS evolution model was experimentally determined from hot torsion test according to Hodgson's model. The predicted results were in a reasonably good agreement with experimental results.

Grain refinement through controlled thermomechanical processing

The major challenge for thermomechanical processing is to extend grain refinement towards lower average grain sizes. However, there is also a need to provide a better understanding of the mechanisms through which the refinement processes proceed. Many recent proposals for advanced thermomechanical processing rely on the dynamic strain induced transformation (DSIT), and the dynamic recrystallisation of austenite as the main refinement mechanisms. These mechanisms are still not fully understood and their clarification can be expected to lead to even greater levels of refinement. The current review examines the roles of ferrite recrystallisation , DSIT and initial austenite grain size. It is shown that although the ferrite recrystallisation mechanism in DSIT has certain similarities with the well known continuous dynamic recrystallisation (CDRX), it is significantly affected by the transformed ferrite grain size. Also, reducing the initial austenite grain size increases the recrystallisation rate in the strain dependent as well as strain independent regions. These results show that the traditional concept of metadynamic recrystallisation is insufficient to explain the changes in grain size following deformation. An alternative explanation is presented.

Grain refinement of pure magnesium using rolled Zirmax® master alloy (MG-33.3ZR)

Owing to the limited solubility of zirconium in molten magnesium, almost all of the zirconium contained in the Zirmax® master alloy (Mg-33.3Zr) is present in the form of nearly pure zirconium particles. Of them, zirconium particle clusters and individual zirconium particles greater than 5

A rationale for the strong dependence of mechanical twinning on grain size

In metals that yield as a consequence of mechanical twinning, the yield stress is a function of the grain size in much the same way as it is for dislocation glide. However, the sensitivity to grain size is typically greater. The intent of the present communication is to show that this can be understood, at least in part, in terms of a size effect that accompanies twinning. Some confirmatory data from a magnesium alloy are presented.

Tensile deformation of a ultrafine-grained aluminium alloy: micro shear banding and grain boundary sliding

This work investigates the relationship between the strain rate and the ductility and the underlying deformation mechanisms in an ultrafine-grained Al6082 alloy. At room temperature the uniform elongation of the material exhibits a marked increase with decreasing strain rate. This effect is related to the activation of micro shear banding, which is controlled by grain boundary sliding. The contribution of these mechanisms to uniform elongation is estimated. It is proposed that the grain boundary sliding suppresses the transformation of micro shear bands into macro shear bands. The activity of other deformation mechanisms during plastic deformation of the ultrafine-grained material is also discussed.

Dependency of recrystallization mechanism to the initial grain size

The effect of initial grain size on the recrystallization behavior of a type 304 austenitic stainless steel during and following hot deformation was investigated using hot torsion. The refinement of the initial grain size to 8 μm, compared with an initial grain size of 35 μm, had considerable effects on the dynamic recrystallization (DRX) and post-DRX phenomena. For both DRX and post-DRX, microstructural investigations using electron backscattered diffraction confirmed an interesting transition from conventional (discontinuous) to continuous DRX with a decrease in the initial grain size. Also, there were unexpected effects of initial grain size on DRX and post-DRX grain sizes.

Effect of grain size on deformation twinning behaviour of high MN steel

The effect of grain size on the mechanical properties and deformation twinning behaviour in high manganese steel was investigated. In order to generate different grain sizes, the samples were subjected to hot rolling, cold rolling and annealing. Room temperature tensile testing of the steel with different grain sizes (5-50 µm) indicated the occurrence of twinning induced plasticity (TWIP) in all the samples. Also, changes in work-hardening behaviour accompanied changes in the grain size. The results are discussed in terms of the enhanced sensitivity of twinning to the grain size.

Realized volatility and correlation in grain futures markets: testing for spillover effects

Fluctuations in commodity prices are a major concern to many market participants. This paper uses realized volatility methods to calculate daily volatility and correlation estimates for three grain futures prices (corn, soybean, and wheat). The realized volatility estimates exhibit properties consistent with the stylized facts observed in earlier studies. According to daily realized correlations and regression coefficients, the spot returns from the three grain futures are positively related. The realized estimates are then used to evaluate the degree of volatility transmission across grain futures prices. The impulse response analysis is conducted by fitting the vector autoregressive model to realized volatility and correlation estimates, using the bootstrap method for statistical inference. The results indicate that rich dynamic interactions exist among the volatilities and correlations across the grain futures markets.

Study of the effect of grain size on the dynamic mechanical properties of microalloyed steels

In the present paper the effect of grain refinement on the dynamic response of ultra fine-grained (UFG) structures for C–Mn and HSLA steels is investigated. A physically based flow stress model (Khan-Huang-Liang, KHL) was used to predict the mechanical response of steel structures over a wide range of strain rates and grain sizes. However, the comparison was restricted to the bcc ferrite structures. In previous work [K. Muszka, P.D. Hodgson, J. Majta, A physical based modeling approach for the dynamic behavior of ultra fine-grained structures, J. Mater. Process. Technol. 177 (2006) 456–460] it was shown that the KHL model has better accuracy for structures with a higher level of refinement (below 1 μm) compared to other flow stress models (e.g. Zerrili-Armstrong model). In the present paper, simulation results using the KHL model were compared with experiments. To provide a wide range of the experimental data, a complex thermomechanical processing was applied. The mechanical behavior of the steels was examined utilizing quasi-static tension and dynamic compression tests. The application of the different deformation histories enabled to obtain complex microstructure evolution that was reflected in the level of ferrite refinement.