Effect of load pattern on solar-boosted heat pump water heater performance

The performance of a solar-boosted heat pump water heater (HPWH) operating under full load and part load conditions was determined in an outdoor experimental study. The system utilised flat unglazed aluminium solar evaporator panels to absorb solar and ambient energy. Absorbed energy was transferred to the water tank by means of the heat pump and a wrap around condenser coil on the outside of the tank. The system COP was found to be in the range of 5–7 under clear daytime conditions and 3–5 under clear night-time conditions. Using part load testing of the HPWH system it was found that concentrating the coils in the lower portion of the tank could increase the efficiency of the condenser coil. It was also shown that there exists a generalised linear relationship that can be used to describe the system COP in terms of the temperature difference between the water in the storage tank and the ambient air.

Nutrition, growth and production of Cherax Destructor Clark, 1936 (Decapoda, Parastacidae)

In this study the nutrition, growth and production of C. destructor was examined. Selected nutritional requirements of juvenile animals were determined under controlled conditions with the aim of developing a pelleted diet for use in hatcheries, nurseries and growout situations. The best developed diet was assessed for its potential as a supplementary feed for animals cultured in earthen environments. The protein requirements were first determined simultaneously with an evaluation of the effect of replacing animal protein (fishmeal) by soybean meal. Juveniles were reared communally for 59 d on isoenergetic diets containing 15-30% protein and graded levels of soybean meal (0-60%, of protein). When soybean meal was included at a level of 40-60%, growth was reduced relative to that achieved with control diets containing 15% and 20% protein, but this was not the case at a 20% soybean meal substitution level. A two-way interaction occurred between dietary protein and soybean meal content. Higher protein feeds enabled higher soybean meal inclusion levels without significantly affecting growth. Protein increases of 5% produced better growth at the 40% and 60% soybean meal substitution levels. This effect was less pronounced in the control and the 20% soybean meal diets. Carcass %protein increased and %lipid decreased as dietary protein increased. A similar effect occurred by increasing the soybean meal level to 60%. No obvious trend in carcass moisture, energy, and ash occurred. A protein requirement of 30% was apparent when fish meal and soybean meal were included in diets at levels of 20% and 24% (dry matter) respectively. Alternative protein sources to soybean meal were subsequently identified. Juveniles were maintained for 12 weeks on isoenergetic diets containing 30% protein and differing in the primary source of protein used, with meat, snail, soybean, yabby, and zooplankton meals comprising the major protein ingredient. No significant difference occurred in mean weight (MW), percentage weight gain (%WG), SGR or survival among diets. Food conversion ratios (FCR) were low, with a minimum value of 0.95 for the snail-based diet. The apparent net protein utilisation (ANPU) varied from 29.6% (zooplankton-based diet) to 41.2% (snail-based diet). Carcass composition varied with diet, with the greatest difference occurring in carapace colour. Animals fed the zooplankton-based diet developed the strongest, most natural pigmentation. A new combination of previously used protein-based ingredients was subsequently tested with reference to two yabby species, Cherax albidus and Cherax destructor, that were grown simultaneously in identical conditions. Juvenile male animals were reared individually for 20 weeks on isoenergetic diets containing 15% or 30% protein with fish meal, soybean meal, yabby meal and wheat products forming the basis of the diets. C albidus grew the fastest and utilised the food the most effectively. Carcass composition was influenced by diet with the 30% protein diet resulting in an increase in carcass protein and ash and a decrease in carcass lipid and energy relative to the low protein diet. Carcass moisture and calcium were not affected by diet. The intermoult period (IP) was highly dependent on the premoult weight (W) but the mean moult increment (WI, as weight) was independent of the PM. The orbital carapace length (OCL) and the abdominal length (ABL) %moult increments generally declined with an increase in PM whereas the propus length (PL) %moult increment generally increased. The IP, WI, %OCL, %ABL, and %PL moult increments varied according to diet and to species. Elevated dietary protein caused a reduction to the IP (for similar sized animals) by 11 d and 7 d and an increase to the WI by 85% and 81% in C. albidus and C destructor respectively. Dietary induced morphological changes also occurred. Animals of a standard OCL (both species) had significantly larger abdomens when fed the higher protein diet. Growth on the best developed diet was compared to the growth obtained on a natural diet of freshwater zooplankton. Juveniles were reared individually for 12 weeks on the two diets. The MW, %WG and SGR were higher for the zooplankton diet. Carcass composition was influenced by diet and the zooplankton fed animals had a higher carcass %protein, %lipid, %ash and %fibre content and were more richly pigmented than animals fed pellets. The IP and the WI were highly dependent on the PM and varied according to diet; feeding with zooplankton reduced the IP by 1.2 days and increased the WI by 13.7% compared to pellets. Nutrient digestibility was determined for the pelleted diets evaluated in the growth trials. Protein digestibility (PD) and dry matter digestibility (DMD), using chromic oxide (Cr2O3) as an exogenous marker, were high for all diets, at around 93% and 83% respectively. Ash digestibility varied considerably from 17% to 73% for the snail and yabby meal diets respectively. Crude fibre digestibility was around 50% and probably indicates cellulase activity. Alternative markers to Cr2O3 were evaluated. Ash was considered to be the most suitable alternative to Cr2O3, providing a reasonable, albeit lower, estimate of nutrient digestibility. Cr2O3 and ash were preferentially excreted whereas fibre was retained in the digestive system for a longer period, consequently, the collection of a particular fraction of the deposited faeces (late or early) substantially affected the digestibility coefficients. In earthen-based environments, animals fed the best developed diet were compared to animals cultured using a forage crop of clover (Trifolium repens). Three supplementary feeding strategies representing varying levels of management intensity were evaluated in a series of trials conducted in ponds and pond microcosms. Growth on pellets consistently exceeded that obtained with the forage crop, with final MW being 67-159% higher than that using clover and appeared to be the result of direct pellet consumption and from a pellet fertiliser effect (on the sediment). Within-pond DMD and PD were high and similar for each treatment (DMD = 51-58%; PD = 89-92%). In the control pond, DMD and PD increased with each successive flood. The faecal egestion rate (PER) decreased with each successive flood in all ponds, and is negatively related to animal weight and to foregut fullness (FF) according to power curves. FF was consistently lowest in the control pond. Mean FF was 48.5%, 62.3%, and 26.7% for the pellet, crop and control ponds respectively. FF increased to the third flood in each pond. The foregut protein content was high in all samples and the mean values were 33.9%, 32.7% and 35.6% for the pellet, crop and control ponds respectively. Foregut ash was highly variable within each pond and is inversely related to the foregut protein content. In the control and pellet ponds the highest foregut ash content occurred during flood 1. The culture system (aquaria or pond) strongly influenced the composition of the foregut content. The foregut of animals fed the manufactured diet (B2) in ponds contained approximately 176% more ash and 5% more protein than the foregut of animals fed in bare-bottom tanks. The FF of the tank fed animals was approximately 45% higher than the FF of pond fed animals after a similar feeding period. Base-line yields for extensive production systems appeared to be around 400kg ha-1. The supplementary addition of T. repens produced yields of approximately 635kg ha-1 (in ponds) to around 1086kg ha-1 (in tanks). The sequential addition of cut-clover to tanks stimulated growth to levels approaching those achieved on pellets. Yabbies stocked into ponds at 15-20 m-2 with a mean weight of 2.67g and fed a 30% protein pelleted diet for 100 d, resulted in a yield of approximately 1117kg ha-1, but only 2% of the population were above a marketable size of 50g. The feed utilisation indices were better for animals reared on pellets in bare-bottom tanks than in earthen environments, indicating some degree of pellet wastage when natural feeds are simultaneously present. High apparent food conversion ratios and low protein efficiency ratios occurred when the forage crop was provided. A considerable quantity of the dry matter and protein content of the forage crop was either inefficiently utilised or directed into other production pathways. Sowing a forage crop into pond microcosms to which a pelleted diet was also provided, did not enhance growth performance. Pelleted feed inputs at a rate of approximately 129g m-2 to 198g m-2 (dry matter) and 38g -2 to 64g m-2 (protein) over 70-100 d resulted in acceptable growth and feed utilisation indices for animals reared in ponds and pond microcosms. Forage crop inputs of approximately 533g m-2 to 680g m-2 (as dry matter) or 84g m-2 to 177g m-2 (as protein) over a 70-100 d period produced reasonable growth rates but poor feed utilisation indices. Low inputs of dry matter (from 113-296g m-2) and protein (from 24-54g m-2) from clover were sufficient to maintain high growth rates in pond microcosms for around 28 d. In ponds, a very low level of 21g m-2 (dry matter) and 4.3g m-2 (protein) was sufficient for around 3 weeks. Forage depletion appeared to occur beyond week 3-4 and was probably a major growth limiting factor. The mean hepatosomatic index (HSI) was 9.44, 7.68, and 6.79 for the pellet, crop, and control ponds respectively. The relationship between hepatopancreas weight and overall animal weight was significantly different between treatments. The hepatopancreas of pellet-fed animals had the highest %lipid and lowest %ash, %protein, %carbohydrate and %moisture content. In terms of absolute quantities, the only major difference in hepatopancreas composition between treatments occurred for lipid and dry matter content. The hepatopancreas of the pellet-fed animals was a cream/cream-yellow colour and was very fragile, whereas in the other ponds it was a more ‘natural’ bright yellow colour and was structurally more robust. C. destructor has a capacious foregut, being approximately 5 times the volume of similar sized Penaeids. The foregut volume (V, ml) of the yabby is related to animal weight (W, g) according to V = 0.048 W0.9543. Animals that were starved for 96 h and then fed diet B2 were almost completely foil after 30 min. The ‘apparent enzymatic response’ of animals fed various natural and artificial diets in tanks was evaluated. Nutrient processing time and the enzymatic response following ingestion appeared to be regulated by the chemical and physical properties of the diet. For the natural feeds, foregut protein was 1.2% higher (for zooplankton) and up to 300% higher (for detritus) than dietary protein, whereas ash was 7.5% higher (zooplankton) and 46-63% lower (detritus) than dietary ash. For animals fed diet B2 after 48 h without food, FF was approximately half that of 96 h starved animals after a similar feeding period but foregut protein and ash contents were similar. Finally, the physiological and morphological attributes elucidated in this study are discussed with reference to the ecology of the yabby. High growth rates, excellent feed utilisation indices and high digestibility coefficients for a wide range of diet-types illustrate nutritional flexibility. A capacious foregut, a large hepatopancreas with a high energy storage capacity, the ability to partition and preferentially excrete the low nutrient value inorganic component of the diet, the capacity to alter body form, nutrient processing time and enzymatic secretions in relation to diet-type, and modified behaviour according to feed availability also demonstrate plasticity/adaptability/flexibility. The combined effect of these important characteristics ensures survival in environments that may be adverse and highly variable in terms of nutrient availability. Collectively the morphological and digestive traits elucidated in this study reflect the generalist-type nature of C destructor and indicate that a polytrophic classification still seems appropriate. Several priority areas for further nutrition research are identified and recommendations are made regarding the best-practices to use in the commercial culture of the yabby. Of paramount importance is the further clarification of the nutritional requirements and feeding preferences of animals in various phases of development.

Fuzzy neural networks for control of dynamic systems

This thesis provides a unified and comprehensive treatment of the fuzzy neural networks as the intelligent controllers. This work has been motivated by a need to develop the solid control methodologies capable of coping with the complexity, the nonlinearity, the interactions, and the time variance of the processes under control. In addition, the dynamic behavior of such processes is strongly influenced by the disturbances and the noise, and such processes are characterized by a large degree of uncertainty. Therefore, it is important to integrate an intelligent component to increase the control system ability to extract the functional relationships from the process and to change such relationships to improve the control precision, that is, to display the learning and the reasoning abilities. The objective of this thesis was to develop a self-organizing learning controller for above processes by using a combination of the fuzzy logic and the neural networks. An on-line, direct fuzzy neural controller using the process input-output measurement data and the reference model with both structural and parameter tuning has been developed to fulfill the above objective. A number of practical issues were considered. This includes the dynamic construction of the controller in order to alleviate the bias/variance dilemma, the universal approximation property, and the requirements of the locality and the linearity in the parameters. Several important issues in the intelligent control were also considered such as the overall control scheme, the requirement of the persistency of excitation and the bounded learning rates of the controller for the overall closed loop stability. Other important issues considered in this thesis include the dependence of the generalization ability and the optimization methods on the data distribution, and the requirements for the on-line learning and the feedback structure of the controller. Fuzzy inference specific issues such as the influence of the choice of the defuzzification method, T-norm operator and the membership function on the overall performance of the controller were also discussed. In addition, the e-completeness requirement and the use of the fuzzy similarity measure were also investigated. Main emphasis of the thesis has been on the applications to the real-world problems such as the industrial process control. The applicability of the proposed method has been demonstrated through the empirical studies on several real-world control problems of industrial complexity. This includes the temperature and the number-average molecular weight control in the continuous stirred tank polymerization reactor, and the torsional vibration, the eccentricity, the hardness and the thickness control in the cold rolling mills. Compared to the traditional linear controllers and the dynamically constructed neural network, the proposed fuzzy neural controller shows the highest promise as an effective approach to such nonlinear multi-variable control problems with the strong influence of the disturbances and the noise on the dynamic process behavior. In addition, the applicability of the proposed method beyond the strictly control area has also been investigated, in particular to the data mining and the knowledge elicitation. When compared to the decision tree method and the pruned neural network method for the data mining, the proposed fuzzy neural network is able to achieve a comparable accuracy with a more compact set of rules. In addition, the performance of the proposed fuzzy neural network is much better for the classes with the low occurrences in the data set compared to the decision tree method. Thus, the proposed fuzzy neural network may be very useful in situations where the important information is contained in a small fraction of the available data.

Effects of invertebrate predators and a pesticide on temporary pond microcosms used for aquatic toxicity testing

The effects of increased trophic complexity, through the addition of predatory notonectids (Anisops deanei), on temporary pond microcosms used for aquatic toxicity testing were studied. Replicate microcosms were established using sediment from a dried temporary pond, and treated with one of four concentrations of the organochlorine pesticide endosulfan (0, 1, 10 or 50 μg/L), in the presence or absence of six A. deanei. The tanks were sampled regularly for nine weeks following the addition of the predators and the entire contents of each tank counted after 12 weeks. Analysis using non-metric multidimensional scaling (MDS) and non-parametric MANOVA showed that both Anisops and endosulfan at concentrations >10 μg/L significantly altered community structure. However, an interaction between the effects of Anisops and the effects of endosulfan was not detected. The addition of Anisops did not increase the variability of response and thus did not reduce the sensitivity of the test method.

Understanding quality and equity of schooling in Scotland : locating educational traditions globally

This paper provides a descriptive analysis of the OECD’s (2007) national report on Scottish education, Quality and equity of schooling in Scotland, while also briefly considering the Scottish government’s Diagnostic Report, prepared for the review. The national report is situated against Scottish traditions of schooling, particularly the view that access to academic curricula for all is a democratic and egalitarian approach, and also set against the changing role of the OECD. On the latter, the paper argues that the OECD, in the context of globalisation, has become more of a policy actor in its own right, in addition to its more traditional think-tank function. The OECD is a now significant transnational policy actor in education, contributing to the emergent global education policy field. The overarching argument proffered is that debates provoked by the OECD’s report, for example the David Raffe/Richard Teese exchange in the Scottish Educational Review, 40(1), 2008, stem from tensions between the new supranational expression of political and policy authority as articulated in the OECD’s report and that located more traditionally within the nation. The academic curricula for all, the Scottish tradition, is challenged by the OECD report, which supports more diverse curricula provision, including more vocational education in schools, particularly at the post-compulsory phase. We note, drawing on theoretical and empirical insights of Bourdieu, that the success of the former demands pedagogies which scaffold for those students not possessing the requisite cultural capitals for success with academic curricula, while the latter demands a strategic effort to ensure parity of esteem between different curricular provisions.

Design and simulation of an interdigital-chaotic advection micromixer for lab-on-a-chip applications

The paper presents the design and simulation of a novel passive micromixer. The micromixer consists of two inlet tanks, one mixing channel and two outlet channels. In order to maximise the mixing efficiency, the following considerations are made : (i) The inlet tanks are followed by a series of microchannels, in which the flow is split. The microchannels are arranged in an interdigital manner to  maximise the contact area between the two flows. (ii) The microchannels attached to the lower inlet tank have an upward slope while those attached to the upper tank have a downward slope. The higher-density flow is fed to the lower inlet tank and gets an upward velocity before entering the mixing channel. (iii) Two triangular barriers are placed within the mixing channel to impose chaotic advection and perturb the less-mixed flow along the top and bottom surfaces of the channel. (iv) Finally, two outlet channels are incorporated to discard the less-mixed flow. Three-dimensional simulations are carried out to evaluate the performance of the micromixer. Simulations are performed in the absence and presence of the gravitational force to analyse the influence of gravity on the micromixer. Mixing efficiencies of greater than 92 % are achieved using water and a low-density biological solvent as the mixing fluids.

Nutritional related aspects of the artificial propagation and larval rearing of Macquarie perch, Macquaria Australasica (Cuvier, 1830)

Studies the underlying role of nutrition in the lack of response of captive fish to hypophysation. Aspects studied include morphological characteristics, histology of ovaries, proximate analysis, fatty and amino acid profiles of oocytes, muscle, liver and diets of wild and tank-reared fish, egg and larval quality, amino acid composition of eggs and larvae at different developmental stages, larval feeding and hormone treatments.

Pneumatic vehicle

A pneumatic vehicle is provided with a first sub-assembly with a chassis, part of the vehicle body, a pair of B-pillars, a pair of rear rails, wheels, an elongate aluminum compressed load bearing air tank oriented longitudinally in the chassis, side panels connected to the tank and the wheels, a heat exchanger to heat the compressed air, and an air motor driven by the heated, compressed air and connected to a wheel. A ventilation system has a restrictive solenoid valve for directing air to the heat exchanger. The air tank is provided with a carbon filament reinforced plastic layer, and a fiberglass and aramid-fiber layer. A second sub-assembly includes part of the vehicle body bonded to the first-sub-assembly using a structural adhesive, a pair of A-pillars, and a pair of roof rails. Seating includes inflatable components for adjustment.

CHASSIS FOR PNEUMATIC VEHICLE

A pneumatic vehicle is provided with a first sub-assembly with a chassis, part of the vehicle body, a pair of B-pillars, a pair of rear rails, wheels, an elongate aluminum compressed load bearing air tank oriented longitudinally in the chassis, side panels connected to the tank and the wheels, a heat exchanger to heat the compressed air, and an air motor driven by the heated, compressed air and connected to a wheel. A ventilation system has a restrictive solenoid valve for directing air to the heat exchanger. The air tank is provided with a carbon filament reinforced plastic layer, and a fiberglass and aramid-fiber layer. A second sub-assembly includes part of the vehicle body bonded to the first-sub-assembly using a structural adhesive, a pair of A-pillars, and a pair of roof rails. Seating includes inflatable components for adjustment.

PNEUMATIC POWERTRAIN FOR AN AUTOMOTIVE VEHICLE

A pneumatic vehicle is provided with a chassis, wheels, a compressed air tank, a heat exchanger to heat the compressed air, and an air motor driven by the heated air and connected to at least one wheel. A pneumatic vehicle is provided with a chassis, wheels, a compressed air tank, and an air motor driven by the compressed air and connected to a wheel. The vehicle also has a ventilation system for the passenger compartment, a heat exchanger, and a restrictive solenoid valve for directing ventilation system air to the heat exchanger. A pneumatic vehicle is provided with a chassis, wheels, an aluminum compressed air tank, a carbon filament reinforced plastic layer over the tank, a fiberglass and aramid-fiber layer over the carbon filament reinforced plastic layer, and an air motor driven by the compressed air and connected to at least one wheel.

BODY FOR PNEUMATIC VEHICLE

A pneumatic vehicle is provided with a first and second sub-assembly. The first sub-assembly has a chassis supporting an air tank. The second sub-assembly has part of the vehicle body and is bonded to the first-sub-assembly using a structural adhesive. Another pneumatic vehicle is provided with a first and second sub-assembly. The first sub-assembly has a chassis, air tank, part of the vehicle body, a pair of B-pillars, and a pair of rear rails. The second sub-assembly has a part of the vehicle body, a pair of A-pillars, and a pair of roof rails. A vehicle seat is provided with a seat base and upright seat back providing a seating area. A bladder located in the central region of the seating area inflates to provide two bucket seats, and deflates to provide a bench seat. The vehicle seat also has inflatable inserts to provide cushioning.

PNEUMATIC VEHICLE

A pneumatic vehicle is provided with a first sub- assembly with a chassis, part of the vehicle body, a pair of B-pillars, a pair of rear rails, wheels, an elongate aluminum compressed load bearing air tank oriented longitudinally in the chassis, side panels connected to the tank and the wheels, a heat exchanger to heat the compressed air, and an air motor driven by the heated, compressed air and connected to a wheel. A ventilation system has a restrictive solenoid valve for directing air to the heat exchanger. The air tank is provided with a carbon filament reinforced plastic layer, and a fiberglass and aramid-fiber layer. A second sub-assembly includes part of the vehicle body bonded to the first-sub-assembly using a structural adhesive, a pair of A-pillars, and a pair of roof rails. Seating includes inflatable components for adjustment.

Performance of an oxidation ditch retrofitted with a membrane bioreactor during the start-up

The objective of this study is to elucidate the full-scale characteristics of an oxidation ditch (OD) retrofitted with a membrane bioreactor (MBR). Domestic wastewater entering an oxidation ditch at a flow rate of 86 m3/d was directed to a MBR retrofitted into the original secondary sedimentation tank. The MBR contained flat sheet membranes. The data collected for 2 months during the start-up of the system showed that pH was maintained at 7.2 and 6.7 in OD and MBR, respectively. Dissolved oxygen (DO) in MBR remained stable at 7.8 mg/L, while fluctuated in OD. The mixed liquor suspended solids (MLSS) in the OD remained steady at a concentration about 1000 mg/L, but it was gradually building up from 500 mg/L to 2400 mg/L in the MBR during this period. Measurements of carbohydrate and protein were made by extracting the extra cellular polymeric substances (EPS) with sodium hydroxide (NaOH) from the mixed liquor obtained from both OD and MBR. Carbohydrate was predominant in the EPS and the ratios between carbohydrate and protein converged to fixed values from the fourth week; in this case the ratio was 4.5 for OD and 5 for MBR. The variation in EPS contents showed similar trends in both OD and MBR. The integrated treatment facility removed ammonia, COD and BOD at 100, 91.6 and 97.0%, respectively. However, efficiency of nitrate and phosphate removal has not been realized yet.

Powdered activated carbon for fouling reduction of membrane in a pilot-scale recirculation aquaculture system

Recirculating aquaculture systems (RAS) are essential for the reduction in fresh water usage as well as the discharge of nutrients along with aquaculture effluents. A RAS consisting of an anoxic reactor, a membrane bioreactor (MBR) and a UV-disinfection unit was used to process 10,000 L/d of aquaculture effluent providing high-quality treated water for recirculation to a Barramundi fish culture. The system maintained low levels of nitrate (<20 mg/L), nitrite (<3 mg/L) and ammonia (<0.6 mg/L) in the fish tank. Permeate from the membrane that was recirculated to the fish tank contained <21 mg/L of nitrate, <2 mg/L of nitrite and 0 mg/L of ammonia. However, the rate of fouling of the membrane in the MBR was around 1.47 kPa/d, and the membrane in the MBR required cleaning due to fouling after 16 days. Cleaning of the membrane was initiated when the TMP reached around 25 to 30 kPa. In order to reduce the rate of fouling, 500 mg of powdered activated carbon (PAC) per litre of MBR volume was introduced, which decreased the rate of fouling to 0.90 kPa/d. Cleaning of membrane was needed only after 31 days of operation while maintaining the treated effluent quality. Thus the frequency of cleaning could be halved due to the introduction of PAC into the MBR.

Integrated fluid-thermal-structural numerical analysis for the quenching of metallic components

The quenching of a metal component with a channel section in a water tank is numerically simulated. Computational fluid dynamics (CFD) is used to model the multiphase flow and the heat transfer in film boiling, nucleate boiling and convective cooling processes to calculate the difference in heat transfer rate around the component and then combining with the thermal simulation and structure analysis of the component to study the effect of heat transfer rate on the distortion of the U-channel component. A model is also established to calculate the residual stress produced by quenching. The coupling fluid-thermal-structural simulation provides an insight into the deformation of the component and can be used to perform parameter analysis to reduce the distortion of the component. © 2011 Shanghai Jiaotong University and Springer-Verlag Berlin Heidelberg.