The reliability of muscle biopsies taken from vastus lateralis

The purpose of this study was to examine whether a single biopsy sample of vastus lateralis could provide an accurate estimate of capillary density (CD) which is indicative of the entire muscle, or whether capillary density is distributed unevenly and varies with muscle depth. Whole muscle cross sections of vastus lateralis were excised post mortem (n=11) for analysis of capillary density at three muscle depths, (superficial, mid and deep regions). Muscle thickness varied widely (17–79mm) across subjects. The distribution of CD throughout the depth of the muscle was homogeneous in 8 subjects, but in 3 subjects it was heterogeneous (p<0.05). In 3 of these subjects there was a significant (p<0.05) effect of sample depth on CD. These data indicate that tissue from a single biopsy will not adequately represent the CD of the entire vastus lateralis in some individuals. Single biopsies from unspecified muscle depth, have routinely been used to estimate CD and fibre type in vastus lateralis. The present study indicates that a more reliable method of analysis would be to use the tissue from two needle biopsies taken at the superficial and deep portions of the muscle from a group of at least 10 subjects. Sampling theory analysis supported this conclusion.

Focused ion beam milling of carbon nanotube yarns and bucky-papers : correlating their internal structure with their macro-properties

Focused ion beam (FIB) milling through carbon nanotube (CNT) yarns and bucky-papers followed by scanning electron microscopy has recently emerged as a powerful tool for eliciting details of their internal structure. The internal arrangement of CNTs in bucky-papers and yarns directly affects their performance and characteristics. Consequently this information is critical for further optimisation of these structures and to tailor their properties for specific applications. This chapter describes in detail FIB milling of CNT yarns and bucky-papers and gives a range of examples where FIB milling has enabled a better understanding of how processing conditions and treatments affect the internal structure. Emphasis is placed on how FIB milling elucidates the influence of fabrication conditions on the internal arrangement of CNTs and how this influences the material's macroscopic properties.

Qualitative spectroscopic characterization of the matrix-silane coupling agent interface across metal fibre reinforced ion exchange resin composite membranes

The characterization of novel metal reinforced electro-dialysis ion exchange membranes, for water desalination, by attenuated total reflectance Fourier transform infrared spectroscopy mapping is presented in this paper. The surface of the porous stainless steel fibre meshes was treated in order to enhance the amount of surface oxide groups and increase the material hydrophilicity. Then, the metal membranes were functionalized through a sol-gel reaction with silane coupling agents to enhance the affinity with the ion exchange resins and avoid premature metal oxidation due to redox reactions at the metal-polymer interface. Polished cross sections of the composite membranes embedded into an epoxy resin revealed interfaces between metallic frameworks and the silane layer at the interface with the ion exchange material. The morphology of the metal-polymer interface was investigated with scanning electron microscopy and Fourier transform infrared micro-spectroscopy. Fourier transform infrared mapping of the interfaces was performed using the attenuated total reflectance mode on the polished cross-sections at the Australian Synchrotron. The nature of the interface between the metal framework and the ion exchange resin was shown to be homogeneous and the coating thickness was found to be around 1 μm determined by Fourier transform infrared micro-spectroscopy mapping. The impact of the coating on the properties of the membranes and their potential for water desalination by electro-dialysis are also discussed.

An extension of the flower pattern diagram for roll forming

The initial process design of a roll forming system is often based on the traditional ‘flower pattern diagram’. In this diagram, the cross sections of the strip at each roll stand are superimposed on a single plane; the diagram is a 2D representation of the 3D process. In the present work, the flower pattern is extended into three dimensions. To demonstrate the method, the forming path or trajectory of a point at the edge of the strip during forming a V-section is considered. The forming path is a surface curve that lies on a cylindrical surface having its axis along the machine axis. This surface is unwrapped to give its plane development and important features of the forming process can be determined and are readily interpreted from this plane curve. It is shown that at any stage in the process, the axial strain and the curvature of the sheet adjacent to the point are dependent on the slope of the trajectory in this plane projection. This new diagram, which apparently has not been used previously, provides a useful initial method of examining the roll forming process and optimising the flower pattern. The model is purely geometric, as is the original flower pattern approach, and does not include the effect of material behaviour. The concept is applied to several cases available in the literature. It shows that the lowest level of shape defect in the part is achieved when the trajectory of the strip edge follows the shortest line length between the start and finish of forming, leading to the least longitudinal strain introduced in the flange. This trend is in agreement with previous experimental observations, suggesting that the analytical model proposed may be applied for early process design and optimisation before time-consuming numerical analysis is performed.

Fabrication of polymeric microchannels with focused and defocused CO2 lasers

 The control of energy distribution or energy intensity inside a laser spot using a defocusing method enables the formation of high-quality microchannels of multiple cross-sections in polycarbonate. Moreover, a thermal mathematical model of the process was developed to aid understanding of the process and to allow channel topology prediction.