Twinning and the ductility of magnesium alloys Part I: “Tension” twins

Magnesium and its alloys do not in general undergo the same extended range of plasticity as their competitor structural metals. The present work is part I of a study that examines some of the roles deformation twinning might play in the phenomenon. A series of tensile test results are reported for the common wrought alloy AZ31. These data are employed in conjunction with a simple constitutive model to argue that View the MathML source twinning (which gives extension along the c-axis) can increase the uniform elongation in tensile tests. This effect appears to be similar to that seen in Ti, Zr and Cu–Si and in the so called TWIP phenomenon in steel.

Extrusion limits of magnesium alloys

Magnesium alloys are generally found to be slower to extrude than aluminum alloys; however, limited quantitative comparisons of the actual operating windows have been published. In this work, the extrusion limits are determined for a series of commercial magnesium alloys (M1, ZM21, AZ31, AZ61, and ZK60). These are compared with the limits established for aluminum alloy AA6063. The maximum extrusion speed of alloy M1 is shown to be similar to AA6063. Alloys ZM21, AZ31, ZK60, and AZ61 exhibit maximum extrusion speeds 44, 18, 4, and 3 pct, respectively, of the maximum measured for AA6063. For AZ31, the maximum extrusion speed is increased by 22 pct after homogenization and by 64 pct for repeat extrusions. The variation in the extrusion limits with changing alloy content is rationalized in terms of differences in the hot working flow stress and solidus temperature.

Grain size in Mg alloys: recrystallization and mechanical consequences

The present paper examines the development of grain size during the recrystallization of magnesium alloys and the influence the grain size has on the mechanical response. In magnesium alloys grain refinement improves the strength-ductility balance. This simultaneous increase in both strength and ductility is ascribed to the impact the grain size has on deformation twinning. The mechanisms by which the grain size is established during hot working are shown to be conventional dynamic recrystallization followed by post-dynamic recrystallization. The role of alloying additionon both of these reactions is briefly considered.

Effect of solidification grain refinement on the development of wrought Mg alloys

A recent trial investigated the effect of solidification grain refinement of billet on the grain refinement and properties of alloy ZM20. It was found that even at levels of 0.4Mn, significant grain refinement could be obtained when 0.7Zr was added. At 0.2Mn grain sizes as low as 60μm were
obtained. Billets of Mg-2Zn-0.2Mn with four different grain sizes, due to different Zr and cooling rates were then cast via vertical direct chill casting and extruded conventionally. Benefits of grain refinement of the billet on extrusion were found to be a slight increase in the size of the operating
window, and a reduction of the grain size in the extrudate. However, the effect of the reduction in extrudate grain size due to refinement of the billet was small compared with the amount of grain refinement obtained due to recrystallisation on extrusion.

A criterion for conventional dynamic recrystallization: Application to magnesium alloys

An analytical approximation for the steady state dynamic recrystallized grain size is combined with a simple nucleation criterion to assess the propensity for dynamic recrystallization. In line with observation, the criterion predicts dynamic recrystallization in 99.9995% pure Al but not in material 99.5% pure. It also agrees with the observation that zone refined ferrite can display dynamic recrystallization at high temperatures and low strain rates but not at lower hot working temperatures. The criterion is applied here to common wrought magnesium alloys to argue that conventional dynamic recrystallization is expected under "normal" hot working conditions.

Expanding the extrusion limits of wrought magnesium alloys

Consumption of wrought magnesium products wax reduced by half between 1971 and the 1990s. To increase the use of wrought magnesium, several challenges must be overcome: its formability at room temperature is lower than steel or aluminum; its productivity is lower than steel or aluminum; and extruded magnesium exhibits a marked anisotropy of yield when comparing tension and compression. This article describes research on the rapid evaluation of the extrusion behavior of wrought magnesium alloys. The work aims to establish a methodology for rapid prototyping of alloys and to assess the effects of aluminum on the behavior of AZ-series magnesium alloys.

Computer aided analysis of dental radiographic images

This paper is a result of a fruitful cooperation between the computer science and the dental diagnosis experiences. The study presents a new approach of applying computer algorithms to radiographic images of dental implantation used for bone regeneration. We focus here only on the contribution of the computer assistance to the clinical research as the periodontal therapy is beyond the scope of this paper. The proposed system is based on a pattern recognition approach, directed to recognize density changes in the intra-bony affected areas of patients. It comprises different modules with new algorithms specially designed to treat the patients’ radiographic images more accurately. The system includes digitizing, detecting the complicated region of interest (ROI), defining reference area to correct any projection discrepancy of the follow up images, and finally to extract the distinguishing features of the ROI as a basis for determining the rate of new bone density accumulation. This study is applied to two typical dental cases for a patient who received two different operations. The results are very encouraging and more accurate than traditional techniques reported before.

Solidification of cast magnesium alloys

A description of the key solidification steps in the formation of the as-cast microstructure of magnesium alloys is presented. The focus is on the two common magnesium alloy groups: Mg-Al alloys and Mg-Zn-rare earth alloys. The key elements described are: nucleation (including grain refinement), growth of the primary phase and the formation of the eutectic phases. In addition the effect of casting process (e.g. high-pressure diecasting and sand casting) on the outcomes from solidification are discussed. This includes consideration of the formation of banded defects during solidification in the dynamic environment of high pressure die casting.

A calibration for surface analysis on aluminium alloys by RF-Glow-Discharge Optical Emission Spectrometry

Glow-Discharge Optical Emission Spectrometry (GD-OES) is a powerful technique for the rapid analysis of elements in a solid surface as a function of depth. DC-GD-OES allows depth profiling on electrically conductive surfaces only, and has proven to be difficult for the analysis of insulating layers, such as oxides. However, the technique of radio-frequency (RF) GD-OES has the advantage of being able to depth profile through multiple layers, both conducting and insulating. In this work, a LECO GDS- 850A spectrometer was calibrated for aluminium, oxygen, and other elements, with the RF source installed. A quantitative depth profile for a sample of tempered aluminium alloy 7475 is presented and compared with earlier work[1,2].

Effect of composition on the texture and deformation behaviour of wrought Mg alloys

The microstructure and mechanical response of three extruded magnesium alloys, Mg-3Al-1Zn (AZ31), Mg-1.5Mn (Ml) and Mg-lMn-0.4RE (ME10) are examined. The tensile yield strength of ME10 was nearly half that of AZ31 and Ml. The tensile elongations were 6%, 11% and 19% for Ml, AZ31 and ME10, respectively. This range of properties is large and is attributed to the unique extrusion texture produced in ME10, and the high density of fine particles in Ml.

The origin of "Rare Earth" texture development in extruded Mg-based alloys and its effect on tensile ductility

The extrusion behaviour, texture and tensile ductility of five binary Mg-based alloys have been examined and compared to pure Mg. The five alloying additions examined were Al, Sn, Ca, La and Gd. When these alloys are compared at equivalent grain size, the La- and Gd-containing alloys show the best ductilities. This has been attributed to a weaker extrusion texture. These two alloying additions, La and Gd, were found to also produce a new texture peak with View the MathML source parallel to the extrusion direction. This “rare earth texture” component was found to be suppressed at high extrusion temperatures. It is proposed that the View the MathML source texture component arises from oriented nucleation at shear bands.