Fabrication and characterisation of carbon nanofibres from cellulose nanofibres

Carbon nanofibers were fabricated by pyrolysis of plant-based cellulose nanofibers. The findings demonstrate the possibility of obtaining strong and commercially competitive carbon nanofibers that are used in many industries including aerospace, automobile and electronics.

Cellulose-based biodegradable blends and composites regenerated from ionic liquids

This thesis presents the fabrication of biodegradable polymer blends and composites with the assistance of ionic liquids. The work included preparation and characterization of cellulose/PCL blend films, cellulose/ PCL-PDMS-PCL blend films, cellulose/ PVAL blend films and cellulose/clay composite films. An efficient and feasible approach of reducing plastic pollution was developed.

Surface-sensitive method to determine calcium carbonate filler contents in cellulose matrices

This paper describes a method using attenuated total reflectance infra-red spectroscopy to determine the surface concentration of calcium carbonate in paper samples, by applying the linear relationship between the relative infra-red absorption integrals and the concentration. The method was able to detect micro-variations in the surface concentration and could also distinguish between different sheets as well as between the top and bottom side of one sheet. The samples were also split and the calcium carbonate concentration was determined within and compared to bulk calcium carbonate concentration determined from ash testing. The surface results were also compared with analysed scanning electron microscopy images generated from back-scattering electrons. The comparison shows that both sets of results are in excellent agreement. Depending on the sample, large errors (95% confidence) were observed. These, however, are caused by micro-variations of the surface concentration, rather than by inaccuracies of the technique, which is estimated to be less than 1%. Furthermore, measurements of various sample orientations suggest that anisotropic polarisation effects can be neglected. The method can be applied to paper and cellulose matrices having calcium carbonate filler contents of less than 50%. Due to spectral overlaps it is not suitable to determine kaolin filler contents.

Cellulose nanofibre textured SERS substrate

Poor reproducibility limits the wide uptake of low-cost surface enhanced Raman spectroscopy (SERS) substrates. This study reports a relatively low-cost and reproducible cellulose nanofibre (CNF) textured SERS substrate. Utilizing a layer of CNFs deposited onto glass slides, nanoscale roughness was achieved, which facilitated effective aggregation of gold nanoparticles (AuNPs) to form a novel CNF textured SERS substrate. This substrate meets the critical roughness requirements to control the distribution of AuNPs to provide 'hot spots' for SERS detection, offering significant signal enhancement. The reproducibility and accuracy of low-cost cellulosic SERS substrates were significantly improved on a model SERS molecule of 4-aminothiophenol.

Enhancing the carbon yield of cellulose based carbon fibres with ionic liquid impregnates

Here we show that ionic liquids (ILs), protic or aprotic in nature containing a phosphate anion, can be used as effective impregnating compounds resulting in a 50% improvement of the carbon yield of cellulose based carbon fibres and a 70 °C reduction in the onset of the depolymerization temperature. Using 13C NMR and FTIR spectra, we characterize the carbonized fibres with and without IL impregnates. The oxidative step in the formation of carbon fibres from cellulose precursors is very important in determining the final material properties, as such we examine this stage and show that the IL reduces the onset of the cellulose depolymerization temperature while improving the oxidative stability. This study highlights the ability of ILs to act as novel impregnates which can successfully reduce the formation of tar and volatile substances during carbonization of cellulose based carbon fibres resulting in an improved carbon yield and significant cost savings due to reduced maintenance and wear of equipment. This journal is

Preparation of pH- and salinity-responsive cellulose copolymer in ionic liquid

A novel biodegradable pH- and salinity-responsive cellulose copolymer was prepared by grafting 2-(Dimethylamino) ethylmethacrylate (DMAEMA) onto bagasse cellulose in ionic liquid. The grafting polymerization was achieved in 1-butyl-3-methylimidazolium chloride ([Bmim]Cl) under microwave irradiation. Copolymers were then characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, X-ray diffraction and thermo gravimetric analysis measurements. The results revealed that polymer chains had been successfully bonded to the cellulose backbone. Furthermore, the self-assembly of cellulose-g-DMAEMA copolymers at various salt concentrations and pH solution were investigated by means of swelling behavior measurement. It indicated that the copolymers presented dual pH and salinity-responsive properties. The synthetic strategy showed great potential in the modification of other cellulosic biomass to afford new biomaterials with desired properties. © 2014 Springer Science+Business Media Dordrecht.

Preparation of cellulose nanofiber from softwood pulp by ball milling

This paper reports the possibility of producing cellulose nanofiber from softwood pulp using a simple ball milling technique under ambient pressure and at room temperature. The effects of milling conditions including the ball-to-cellulose mass ratio, milling time, ball size and alkaline pretreatment were investigated. It was found that milling-ball size should be carefully selected for producing fibrous morphologies instead of particulates. Milling time and ball-to-cellulose mass ratio were also found important to control the fiber morphology. Alkali pre-treatment helped in weakening hydrogen bonds between cellulose fibrils and removing small particles, but with the risks of damaging the fibrous morphology. In a typical run, cellulose nanofiber with an average diameter of 100 nm was obtained using soft mechanical milling conditions using cerium-doped zirconia balls of 0.4–0.6 mm in diameter within 1.5 h without alkaline pretreatment.

High-performance supercapacitor electrode materials from cellulose-derived carbon nanofibers

Nitrogen-functionalized carbon nanofibers (N-CNFs) were prepared by carbonizing polypyrrole (PPy)-coated cellulose NFs, which were obtained by electrospinning, deacetylation of electrospun cellulose acetate NFs, and PPy polymerization. Supercapacitor electrodes prepared from N-CNFs and a mixture of N-CNFs and Ni(OH)2 showed specific capacitances of ∼236 and ∼1045 F g(-1), respectively. An asymmetric supercapacitor was further fabricated using N-CNFs/Ni(OH)2 and N-CNFs as positive and negative electrodes. The supercapacitor device had a working voltage of 1.6 V in aqueous KOH solution (6.0 M) with an energy density as high as ∼51 (W h) kg(-1) and a maximum power density of ∼117 kW kg(-1). The device had excellent cycle lifetime, which retained ∼84% specific capacitance after 5000 cycles of cyclic voltammetry scans. N-CNFs derived from electrospun cellulose may be useful as an electrode material for development of high-performance supercapacitors and other energy storage devices.