Synthesis of ZnO nanowires using ball-milling and annealing method

Nanowires represent a new class of ZnO morphologies with many exiting new properties and applications. The research in the synthesis and characterization of ZnO nanowires has received enormous attention in recent years. However, most synthesis methods using vapor deposition process can only produce small amount of sample, mass production has not been achieved yet. Large-quantity production of ZnO nanowires needs to be realized for large-scale property and application studies. One of the promising approaches to the large scale synthesis is a ball-milling and annealing method. This paper first introduces several common synthesis methods of ZnO nanowires and then summarizes the one dimensional nanomaterials produced by the ball milling and annealing method. Finally, some preliminary results of ZnO nanowire synthesis are presented.

Controlled growth of zinc nanowires

Zinc nanowires have been synthesized by heating a mixture of boron and zinc oxide (ZnO) powders at 1050 °C under a nitrogen atmosphere. The influences of the gas flow rate and the substrate character on the nanowire formation were investigated. It was found that higher-flow rate of gas led to the formation of thinner nanowires; while lower-flow rate of gas produced thicker nanowires and even particles due to the higher partial pressure of Zn vapor in this case. Zn nanowires can be produced on alumina and quartz substrates, but not on a stainless-steel substrate under the same or different synthetic conditions. Photoluminescence measurements were conducted on Zn nanowires and particles and weak emission bands at 482 and 493 nm were observed, which may be contributed by the thin ZnO film on the nanowire surface.

An effective approach to grow boron nitride nanowires directly on stainless-steel substrates

When growing one-dimensional (1D) nanomaterials via the vapour–liquid–solid (VLS) model, the substrates usually need to be coated with a layer of catalyst film. In this study, however, an effective approach for the synthesis of boron nitride (BN) nanowires directly onto commercial stainless-steel foils has been demonstrated. Growth occurs by heating boron and zinc oxide (ZnO) powders at 1100 °C under a mixture of nitrogen and hydrogen gas flow (200 ml min−1). The stainless-steel foils played an additional role of catalyst besides substrate during the VLS growth of these BN nanowires. The as-synthesized nanowires emit strong photoluminescence (PL) bands at 515, 535 and 728 nm. In addition, we found that the gas flow rate and the hydrogen content in the gas mixture strongly affected the diameter and yield of the nanowires by changing the relative concentration of the nanowire growth species in the chamber.

Pure boron nitride nanowires produced from boron triiodide

A thick layer of pure boron nitride (BN) nanowires with a uniform diameter of 20 nm was synthesized for the first time using a CVD process with a new precursor of boron triiodide (BI3). Transmission electron microscopy revealed a nanocrystalline structure in the BN nanowires and the absence of any catalyst particle. Some BN nanowires self-assembled into thick threads up to several hundred micrometres long on top of the nanowire layer. The nitriding reactions and lack of catalyst suggest new formation mechanisms of the BN nanowires.

Transmission electron microscopy investigation of substitution reactions from carbon nanotube template to silicon carbide nanowires

Substitution reactions between multiwalled carbon nanotubes and silicon monoxide vapour have been investigated using transmission electron microscopy. Different reactions occurred inside the multiwalled nanotubes and on the nanotube external surfaces, resulting in the formation of silicon carbide nanowires with a core–shell structure. The substitution reaction process and end products are strongly affected by nanotube structures and a ball milling treatment of the starting materials.

Boron carbide nanowires with uniform CNχ coatings

Boron carbide nanowires with uniform carbon nitride coating layers were synthesized on a silicon substrate using a simple thermal process. The structure and morphology of the as-synthesized nanowires were characterized using x-ray diffraction, scanning and transmission electron microscopy and electron energy loss spectroscopy. A correlation between the surface smoothness of the nanowire sidewalls and their lateral sizes has been observed and it is a consequence of the anisotropic formation of the coating layers. A growth mechanism is also proposed for these growth phenomena.

Efficient production of ZnO nanowires by a ball milling and annealing method

ZnO powder was mechanically milled in a ball mill. This procedure was found to greatly increase its evaporation ability. The anomalous evaporation behaviour was caused by the disordered structure of the milled material and was not related to the increase in its surface area after milling. ZnO nanowires were synthesized by evaporation of this milled precursor. Nanowires with smooth and rough surfaces were present in the sample; the latter morphology was dominant. A green emission band centred at 510 nm was dominant in the cathodoluminescence spectrum of the nanowires.

Fluoride-assisted synthesis of mullite (Al5.65 Si0.35 O9.175) nanowires

Novel silicon-deficient mullite (Al_5.65Si_0.35O_9.175) single crystal nanowires were synthesized in large quantities on mica substrates assisted by the intermediate fluoride species. The nanowires have diameters in the range 50–100 nm and typical lengths of several µm. Aligned nanowires were observed at the substrate edge. The nanowires have strong photoluminescence (PL) emission bands at 310, 397, 452 and 468 nm.

Selective oxidation synthesis of MnCr2O4 spinel nanowires from Commercial stainless steel foil

For the first time, MnCr₂O₄ spinel single-crystalline nanowires were simply synthesized by heating commercial stainless steel foil (Cr_0.19Fe_0.70Ni_0.11) under a reducing atmosphere. The nanowires have an average diameter of 50 nm and a length of about 10 μm. Some nanowires are sheathed with a thin layer of amorphous silicon oxide. Photoluminescence measurements revealed that the nanowires exhibit an emission band at 435 nm, which resulted from the oxygen-related defects in the silicon oxide sheath. It was found that the reducing atmosphere plays a key role for the nanowire growth. In the reducing atmosphere, the Mn and Cr elements in the stainless steel could be selectively oxidized because of their higher affinity for oxygen than the Fe and Ni elements. The Fe and Ni elements in the stainless steel, however, acted as the catalyst for the vapor–liquid–solid (VLS) growth of the MnCr₂O₄ nanowires.

Characterization of conducting polymer coated fabrics at microwave frequencies

Purpose – The purpose of this paper is to investigate microwave reflection, transmission, and complex permittivity of p-toluene-2-sulfonic acid doped conducting polypyrrole coated nylon-lycra textiles in the 1-18?GHz frequency with a view to potential applications in the interaction of electromagnetic radiation with such coated fabrics.

Design/methodology/approach – The chemical polymerization of pyrrole is achieved by an oxidant, ferric chloride and doped with p-toluene sulfonic acid (pTSA) to enhance the conductivity and improve stability. Permittivity of the conducting textile substrates is performed using a free space transmission method accompanied by a mathematical diffraction reduction method.

Findings – The real part of permittivity increases with polymerization time and dopant concentration, reaching a plateau at certain dopant concentration and polymerization time. The imaginary part of permittivity shows a frequency dependent change throughout the test range. All the samples have higher values of absorption than reflection. The total electromagnetic shielding effectiveness exceeds 80 percent for the highly pTSA doped samples coated for 3?h.

Originality/value – A non-contact, non-destructive free space method thin flexible specimens to be tested with high accuracy across large frequency range. The non-destructive nature of the experiments enables investigation of the stability of the microwave transmission, reflection, absorption and complex permittivity values. Moreover, mathematical removal of the diffraction enables higher accuracy.

The influence of polymerization time and dopant concentration on the absorption of microwave radiation in conducting polypyrrole coated textiles

Temperature changes in conducting polypyrrole/para-toluene-2-sulphonic acid (PPy/pTSA) coated nylon textiles due to microwave absorption in the 8–9 GHz and 15–16 GHz frequency ranges were obtained by a thermography station during simultaneous irradiation of the samples. The temperature values are compared and related to the amounts of reflection, transmission and absorption obtained with a non-contact free space transmission technique, indicating a relationship between microwave absorption and temperature increase. Non-conductive samples showed no temperature increase upon irradiation irrespective of frequency range. The maximum temperature difference of around 4 °C in the conducting fabrics relative to ambient temperature was observed in samples having 48% absorption and 26.5 ± 4% reflection. Samples polymerized for 60 or 120 min with a dopant concentration of 0.018 mol/l or polymerized for 180 min with a dopant concentration of 0.009 mol/l yielded optimum absorption levels. As the surface resistivity decreased and the reflection levels increased, the temperature increase upon irradiation reduced.

Conducting nylon, cotton and wool yarns by continuous vapor polymerization of pyrrole

Conductive textile yarns were prepared by a continuous vapor polymerization method; the application of polypyrrole by the continuous vapor polymerization method used is designed for the easy adaptation into industrial procedures. The resultant conductive yarns were examined by longitudinal and cross-sectional views, clearly showing the varying levels of penetration of the polymer into the yarn structure. It was found that for wool the optimum specific resistance was achieved by using the 400 TPM yarn with a FeCl3 solution concentration of 80 g/L FeCl3 to produce 1.69 Ω g/cm2. For cotton yarn, the optimum specific resistance of 1.53 Ω g/cm2 was obtained with 80 g/L of a FeCl3 solution.

Electroless synthesis of nano-structured gold particles using conducting polymer nanoparticles

In this study, gold nanoparticles were synthesized by electroless recovery of [AuCl4]− from an acidic aqueous solution using nano-structured conducting polymer, polypyrrole nanoparticles, as active surface. The formation of gold nanoparticles was confirmed by TEM, SEM and EDX measurements. The effects of the initial Au(III) concentration on the gold uptake was examined. The recovery capability and gold particle morphology prepared from polypyrrole nanoparticle were compared to that from cast PPy film counterpart.