Experimental and theoretical investigation on corrosion inhibition of AA5052 aluminium alloy by l-cysteine in alkaline solution

The corrosion inhibition of l-cysteine on AA5052 aluminium alloy in 4 mol/L NaOH solution was investigated by hydrogen gas evolution experiment, polarisation curve, galvanostatic discharge, electrochemical impedance spectroscopy measurements and quantum chemical calculations. The adsorption of l-cysteine on aluminium alloy surface obeyed the amended Langmuir's adsorption isotherm. The polarisation curves indicated that l-cysteine acted as a cathodic inhibitor to inhibit cathodic reaction. The inhibition mechanism was dominated by the geometric covering effect. The galvanostatic discharge shows that the additives restrain the hydrogen evolution and increase the anodic utilization rate. Quantum chemical calculations indicated that l-cysteine molecules mainly interacted with on the carboxyl groups on the aluminium alloy surface. A strong hybridization occurred between the s-orbital and p-orbital of reactive sites in the l-cysteine molecule and the sp-orbital of Aluminium.

Investigation on the effect of cutting fluid pressure on surface quality measurement in high speed thread milling of brass alloy (C3600) and aluminium alloy (5083)

The quality of a machined finish plays a major role in the performance of milling operations, good surface quality can significantly improve fatigue strength, corrosion resistance, or creep behaviour as well as surface friction. In this study, the effect of cutting parameters and cutting fluid pressure on the quality measurement of the surface of the crest for threads milled during high speed milling operations has been scrutinised. Cutting fluid pressure, feed rate and spindle speed were the input parameters whilst minimising surface roughness on the crest of the thread was the target. The experimental study was designed using the Taguchi L32 array. Analysing and modelling the effective parameters were carried out using both a multi-layer perceptron (MLP) and radial basis function (RBF) artificial neural networks (ANNs). These were shown to be highly adept for such tasks. In this paper, the analysis of surface roughness at the crest of the thread in high speed thread milling using a high accuracy optical profile-meter is an original contribution to the literature. The experimental results demonstrated that the surface quality in the crest of the thread was improved by increasing cutting speed, feed rate ranging 0.41-0.45 m/min and cutting fluid pressure ranging 2-3.5 bars. These outcomes characterised the ANN as a promising application for surface profile modelling in precision machining.

Fatigue crack growth in ultrafine grained aluminium alloy

The microstructure, fatigue crack growth behaviour and hardness of ultra fine grained 6061 aluminium alloy obtained by equal angle channel processing was studied. ECAP resulted in significant grain refinement down to the sub micron level and corresponding increase in hardness. Results point to a similar fatigue threshold stress intensity range and fatigue crack growth rates for 1, 2, 4 and 6 passes of ECAP.

Electrical discharge machining of 6061 aluminium alloy

The wire electrical discharge machining (EDM) of 6061 aluminium alloy in terms of material removal rate, kerf/slit width, surface finish and wear of electrode wire for different pulse on time and wire tension was studied. Eight experiments were carried out in a wire EDM machine by varying pulse on time and wire tension. It is found that the material removal rate increases with the increase of pulse on time though the wire tension does not affect the material removal rate. It seems that the higher wire tension facilitates steady machining process, which generates low wear in wire electrode and better surface finish. The surface roughness does not change notably with the variation of pulse on time. The appearance of the machined surfaces is very similar under all the machining conditions. The machined surface contains solidified molten material, splash of materials and blisters. The increase of the pulse on time increases the wear of wire electrode due to the increase of heat input. The wear of wire electrode generates tapered slot which has higher kerf width at top side than that at bottom side. The higher electrode wear introduces higher taper.

Performance of wrought aluminium and magnesium alloy tubes in three-point bending

This present work examines the load carrying capacity, energy absorption and fracture characteristics of wrought magnesium and aluminium alloy tubes in three-point bending. Magnesium alloy AZ31, and aluminium alloys 6063 and 7075, were extruded into cylindrical tubes of both equivalent thickness and mass. A strong thickness effect was present meaning that the AZ31 tube had significantly higher load and energy absorption performance than an equivalent mass 6063 tube, albeit not as high as the 7075 tube. Hinge formation and maximum load was delayed for the magnesium alloy, meaning that a high energy absorption rate persisted to higher deformation displacements than the aluminium alloys. It was also found that fracture during deformation was dependent on the indenter diameter, tube thickness and lower support separation.

Prediction of failure in bending of an aluminium sheet alloy

This work is dedicated to numerical prediction of the bending of thin aluminium alloy sheets, with a focus on the material parameter identification and the prediction of rupture with or without pre-strains in tension prior to bending. The experimental database consists of i) mechanical tests at room temperature, such as tension and simple shear, performed at several orientations to the rolling direction and biaxial tension ii) air bending tests of rectangular samples after (or not) pre-straining in tension. The mechanical model is composed of the Yld2004-18p anisotropic yield criterion (Barlat et al. [3]) associated with a mixed hardening rule. The material parameters (altogether 21) are optimized with an inverse approach, in order to minimize the gap between experimental data and model predictions. Then, the Hosford-Coulomb rupture criterion is used in an uncoupled way, and the parameters are determined from tensile tests, both uniaxial and biaxial, with data up to rupture. In a second step, numerical simulations of the bending tests are performed, either on material in its original state or after pre-straining in tension, with pre-strain magnitudes increasing from 0.19 up to 0.3. The comparisons are performed on different outputs: load evolution, strain field and prediction of the rupture. A very good correlation is obtained over all the tests, in the identification step as well as in the validation one. Moreover, the fracture criterion proves to be successful whatever the amount of pre-strain may be. A convincing representation of the mechanical behavior at room temperature for an aluminium alloy is thus obtained.

Deformation behavior of nanostructured aluminum alloy processed by severe plastic deformation

Microstructure and deformation behavior of the commercial aluminum-based Al7.5%Zn–2.7%Mg–2.3%Cu–0.15%Zr alloy subjected to high pressure torsion (HPT) were studied in the present work. A small grain size less than 100 nm, high level of internal stresses and presence of second phase nanoparticles were revealed by transmission electron microscopy (TEM) and X-ray diffraction (XRD). The nanostructured alloy processed by HPT exhibits tensile strength of 800 MPa and ductility of 20% at optimal temperature-strain rate conditions. Unusual influence of a short pre-annealing on tensile strength and ductility of as-processed alloy is discussed.

A calibration for surface analysis on aluminium alloys by RF-Glow-Discharge Optical Emission Spectrometry

Glow-Discharge Optical Emission Spectrometry (GD-OES) is a powerful technique for the rapid analysis of elements in a solid surface as a function of depth. DC-GD-OES allows depth profiling on electrically conductive surfaces only, and has proven to be difficult for the analysis of insulating layers, such as oxides. However, the technique of radio-frequency (RF) GD-OES has the advantage of being able to depth profile through multiple layers, both conducting and insulating. In this work, a LECO GDS- 850A spectrometer was calibrated for aluminium, oxygen, and other elements, with the RF source installed. A quantitative depth profile for a sample of tempered aluminium alloy 7475 is presented and compared with earlier work[1,2].

Geometrical effects on residual stresses in 7050-T7451 aluminum alloy rods subject to laser shock peening

Laser shock peening (LSP) is an emerging surface treatment technology for metallic materials, which appears to produce more significant compressive residual stresses than those from the conventional shot peening (SP) for fatigue, corrosion and wear resistance, etc. The finite element method has been applied to simulate the laser shock peening treatment to provide the overall numerical assessment of the characteristic physical processes and transformations. However, the previous researchers mostly focused on metallic specimens with simple geometry, e.g. flat surface. The current work investigates geometrical effects of metallic specimens with curved surface on the residual stress fields produced by LSP process using three-dimensional finite element (3-D FEM) analysis and aluminium alloy rods with a middle scalloped section subject to two-sided laser shock peening. Specimens were numerically studied to determine dynamic and residual stress fields with varying laser parameters and geometrical parameters, e.g. laser power intensity and radius of the middle scalloped section. The results showed that the geometrical effects of the curved target surface greatly influenced residual stress fields.

Geometrical effects on residual stresses in 7050-T7451 aluminum alloy rods subject to laser shock peening

Laser shock peening (LSP) is an emerging surface treatment technology for metallic materials, which appears to produce more significant compressive residual stresses than those from the conventional shot peening (SP) for fatigue, corrosion and wear resistance, etc. The finite element method has been applied to simulate the laser shock peening treatment to provide the overall numerical assessment of the characteristic physical processes and transformations. However, the previous researchers mostly focused on metallic specimens with simple geometry, e.g. flat surface. The current work investigates geometrical effects of metallic specimens with curved surface on the residual stress fields produced by LSP process using three-dimensional finite element (3-D FEM) analysis and aluminium alloy rods with a middle scalloped section subject to two-sided laser shock peening. Specimens were numerically studied to determine dynamic and residual stress fields with varying laser parameters and geometrical parameters, e.g. laser power intensity and radius of the middle scalloped section. The results showed that the geometrical effects of the curved target surface greatly influenced residual stress fields.

Deformation behaviour of an ultra-fine grained Al6082 alloy

This work focuses on the effect of strain rate on the deformation behaviour of an ultrafine grained Al alloy 6082 produced by equal channel angular  pressing. The uniform tensile elongation was found to increase with  decreasing strain rate very substantially. This effect is discussed in terms of the mechanisms that control plastic deformation of the alloy.

A comparison of phosphorus and fluorine containing IL lubricants for steel on aluminium

Ionic liquids have been shown to be highly effective lubricants for a steel on aluminium system. This work shows that the chemistry of the anion and cation are critical in achieving maximum wear protection. The performance of the ILs containing a diphenylphosphate (DPP) anion all showed low wear, as did some of the tris(pentafluoroethyl)trifluorophosphate (FAP) and bis(trifluoromethanesulfonyl)amide (NTf2) anion containing ILs. However, in the case of the FAP and NTf2 based systems, a cation dependence was observed, with relatively poor wear resistance obtained in the case of an imidazolium FAP and two pyrrolidinium NTf2 salts, probably due to tribocorrosion caused by the fluorine reaction with the aluminium substrate. The systems exhibiting poor performance generally had a lower viscosity, which also impacts on their tribological properties. Those ILs that exhibited low wear were shown to have formed protective tribofilms on the aluminium alloy surface.

Influence of alloying additions on the extrudability of magnesium

The extrusion behaviour of a series of magnesium alloys was investigated and compared to a common aluminium alloy using limit diagrams. The variation in the limits was related to the different flow stress and solidus temperature of each alloy. The findings of this work have enabled predictions of the relative extrudability of new prototype alloys.