Shape memory alloy scaffolds for bone tissue engineering

Titanium alloy scaffolds for bone tissue engineering are receiving increasing attention because their porous structure and mechanical properties can be adjusted to match those of bone. In particular, there is an enormous potential to increase the life of such implant material if the porous structure can be imparted with shape memory properties. In the present study, TiNi scaffolds with a porous structure and high porosities up to 75% were fabricated by powder metallurgy. The porous structure was characterized by scanning electron microscope. The mechanical properties, the shape memory and superelastic effects were investigated by differential scanning calorimetry, nanoindentation and compressive tests. Results indicate that the porous TiNi scaffolds display an open-cell porous structure which provides new bone tissue ingrowth ability. The mechanical properties of the TiNi scaffolds can be tailored to match those of natural bone. Furthermore, the TiNi scaffolds show good shape memory and superelastic effects.

Mechanical properties and blow forming of rolled AZ31 Mg alloy sheet

Rolling was conducted at 373-673 K for AZ31 Mg alloy; mechanical properties of the rolled Mg alloy were investigated by tensile and blow forming tests. The grain sizes of all the rolled specimens were smaller than that of the specimen prior to rolling. At tensile temperatures under 373 K, the rolled specimens showed much higher 0.2% proof stresses than the non-rolled specimens due to their fine-grained microstructure. However, the strength of the rolled specimens decreased significantly at 473 K. Superplastic behavior was obtained at 573-723 K for the specimens rolled at 498 K. Blow forming tests demonstrated that specimens rolled at 498 K exhibited a high degree of formability at 723 K.

Performance of wrought aluminium and magnesium alloy tubes in three-point bending

This present work examines the load carrying capacity, energy absorption and fracture characteristics of wrought magnesium and aluminium alloy tubes in three-point bending. Magnesium alloy AZ31, and aluminium alloys 6063 and 7075, were extruded into cylindrical tubes of both equivalent thickness and mass. A strong thickness effect was present meaning that the AZ31 tube had significantly higher load and energy absorption performance than an equivalent mass 6063 tube, albeit not as high as the 7075 tube. Hinge formation and maximum load was delayed for the magnesium alloy, meaning that a high energy absorption rate persisted to higher deformation displacements than the aluminium alloys. It was also found that fracture during deformation was dependent on the indenter diameter, tube thickness and lower support separation.

Effects of Nd on the microstructures, mechanical properties and in vitro corrosion behavior of cast Mg-1Mn-2Zn-xNd alloys

Effects of neodymium (Nd) on the microstructures, mechanical properties, in vitro corrosion behavior, and cytotoxicity of as-cast Mg- 1Mn-2Zn-xNd alloys (x = 0.5, 1.0, 1.5, mass%) have been investigated to assess whether Nd is an effective element to increase the strength and corrosion resistance of Mg alloys, and to evaluate whether those alloys are suitable for biomedical applications. The microstructures were examined by X-ray diffraction analysis and optical microscopy. The mechanical properties were determined from uniaxial tensile and compressive tests. The corrosion behavior was studied using electrochemical measurement and cytotoxicity was evaluated using osteoblast-like SaOS2 cell. The results indicate that all the cast Mg-1Mn-2Zn-xNd alloys are composed of both alpha phase of magnesium (Mg) and a compound of Mg7Zn3, and their grain sizes decrease with Nd content. Nd is not an effective element to improve the strength and corrosion resistance of cast Mg-Mn-Zn alloys. Increase of Nd content from 0.5 to 1.5 does not significantly change biocompatibility of alloys. The cast alloys exhibit much better corrosion resistance than pure Mg and good biocompatibility.

Using geopolymer to minimise metals leaching from brown coal fly ash

Fly ash is generated from combustion of brown coal in power stations. The majority of fly ash is removed by electrostatic precipitators (ESP) and finally disposed into the landfill as prescribed wastes. A method was studied to add clay materials to the brown coal fly ash in order to form the so-called geopolymer network, which is effective at stopping the metal contents from leaching, and have minimum impact to the environment. The experiments were conducted parallel on leached fly ash and dry precipitator fly ash. The ratios of fly ash and added clay materials were varied to determine the effects of different compositions on leaching rates. Both X-ray diffraction analysis and scanning electron microscopy images showed that as the percentage of fly ash was increased, the formation of geopolymer is reduced. Eighteen metals and heavy metals were targeted during the leaching tests and the leachate samples were analysed using ICP-AES and ICP-MS. It was found that the reduction of metal leaching was achieved by adding up to 60% of fly ash to form the geopolymer like structure. Significant reductions were observed for calcium, strontium and barium. Leached fly ash achieved better stabilisation than dry precipitator fly ash for major elements. It's hard to quantify its effects on trace metals leaching due to their ultra low concentration in the fly ash. The samples spiked with trace metals of lead, zinc, mercury and barium showed remarkable reduction in leaching.

Simulation of Mg sheet press cell materials

Major characteristics of Magnesium alloy are low density (= 1.8 g/cm³) and excellent recyclability; therefore Mg is considered as one of low environmental loading materials. The low-density materials, such as Mg, are suitable for the transportation system to reduce the emission of Co2, save energy resource and increase the safety for accidents like corrosions. In the place, cellular materials like aluminum foams are also low-density materials and can be controlled the stress-strain relation. Combination of Mg alloy and cellular materials, that is Mg cell, is one of the most excellent materials for transportation system, because of its ultra low density. safeties, and recycle ability. To make the Mg cellular materials. there are some problems to solve. One is how to make them uniformly to supply them as same perfonnance materials. One is how to make them inexpensively. Most of cellular materials are very expensive because of there are many processes or special fabrication system to make them. To solve these problems. we investigated the press cell materials. The press cell material consists sheets pressed as cell shape and wall. Therefore, it is very easy to make cellular materials and control validation of the performance of each foam materials. In this paper, we simulated compression tests of this new type of Mg alloy cellular materials under dynamic loading to investigate the relation between the compression speed and the compression behavior to show the shock absorbing capability of this new foam material. It is very important to understand their mechanical properties relatcd with cell shapes and wall to be applied widely.

Sulfur and heavy metals in biological tissue

The correlation between sulfur, metallothionein and heavy metals was investigated in biological samples from the aquatic environment. Samples of orange roughie, shark, goldfish and king crab were analysed for metals and sulfur. Results indicated that there was insufficient evidence to suggest any relationship between sulfur and total metals, but there was sufficient evidence to suggest a significant relationship existed between mercury and total sulfur in the biological tissues examined.

Atmospheric quality and distribution of heavy metals in Argentina employing Tillandsia capillaris as a biomonitor.

The atmospheric quality and distribution of heavy metals were evaluated throughout a wide region of Argentina. In addition, the biomonitor performance of Tillandsia capillaris Ruiz & Pav. f. capillaris was studied in relation to the accumulation of heavy metals and to its physiologic response to air pollutants. A sampling area of 50,000 km2 was selected in the central region of the Argentine Republic. This area was subdivided into grids of 25 x 25 km. Pools of T. capillaris, where present, were collected at each intersection point. From each pool three sub-samples were analyzed independently. Furthermore, five replicates were collected at 20% of the points in order to analyze the variability within the site. The content of Co, Cu, Fe, Ni, Mn, Pb and Zn was determined by Atomic Absorption Spectrometry. Chemical-physiological parameters were also determined to detect symptoms of foliar damage. Chlorophylls, phaeophytins, hydroperoxy conjugated dienes, malondialdehyde and sulfur were quantified in T. capillaris. Some of these parameters were used to calculate a foliar damage index. Data sets were evaluated by one-way ANOVA, correlation analysis, principal component analysis and mapping. Geographical distribution patterns were obtained for the different metals reflecting the contribution of natural and anthropogenic emission sources. According to our results it can be inferred that Fe, Mn and Co probably originated in the soil. For Pb, the highest values were found in the mountainous area, which can be attributed to the presence of Pb in the granitic rocks. Ni showed mainly an anthropogenic origin, with higher values found in places next to industrial centers. For Zn the highest values were in areas of agricultural development. The same was observed for Cu, whose presence could be related to the employment of pesticides. The foliar damage index distribution map showed that the central and southeastern zones were the ones where the major damage in the bioindicator was found. The central zone coincides with the city of Córdoba whereas the southeastern area is strictly agricultural, so the high values found there could be related to the use of pesticides.

Investigation of corrosion inhibition mechanisms of rare-earth mercaptoacetate inhibitors on AA2024-T3

 Corrosion inhibition mechanisms on the aerospace alloy, AA2024-T3, was investigated for the inhibitor combination of rare earth metals and mercaptoacetate. The inhibitor demonstrated synergistic protection for AA2024-T3 from localised corrosion. It is intended to be a more environmentally friendly alternative to toxic chromate-based inhibitors.

Film formation in trihexyl(tetradecyl)phosphonium diphenylphosphate ([P6,6,6,14][dpp]) ionic liquid on AA5083 aluminium alloy

Whilst ionic liquids (IL) have been shown to inhibit corrosion on some reactive metals and alloys by forming a surface film, e.g. Li and Mg, understanding of the interaction between ionic liquids and aluminium is lacking. This research study investigated the viability of film formation on AA5083 Aluminium Alloy by electrochemical treatments in the trihexyl(tetradecyl)phosphonium diphenylphosphate ([P6,6,6,14][dpp]) IL. Two-step anodic treatments were performed on AA5083 in the IL, followed by a comparison of the corrosion behaviour of the IL-treated samples with that of a control. It has been revealed that the two-step IL-treatment led to reduced current densities on AA5083 under cyclic voltammetry scan in the IL before and after the IL-treatment. Lower corrosion rates have been shown on all samples treated in IL at room temperature. Surface characterisation showed a non-uniform porous film on the 50°C IL-treated sample with a film thickness ranging between 37nm and 155nm. The IL-film enhanced the corrosion resistance of AA5083 by protecting the Al-matrix and Fe-rich intermetallic particles (IMPs). Although findings of this study suggest similar IL-film formation as that on Li and Mg, more research needs to be conducted to optimise the electrochemical treatment conditions and ultimately to develop a robust IL-film formation procedure for corrosion protection.

Metals in the environment as risk factors for infectious diseases: gaps and opportunities

Many parts of the world in which common infectious diseases are endemic also have the highest prevalence of trace metal deficiencies or rising rates of trace metal pollution. Infectious diseases can increase human susceptibility to adverse effects of metal exposure (at suboptimal or toxic levels), and metal excess or deficiency can increase the incidence or severity of infectious diseases. The co-clustering of major infectious diseases with trace metal deficiency or toxicity has created a complex web of interactions with serious but poorly understood health repercussions, yet has been largely overlooked in animal and human studies. This book focuses on the distribution, trafficking, fate, and effects of trace metals in biological systems. Its goal is to enhance our understanding of the relationships between homeostatic mechanisms of trace metals and the pathogenesis of infectious diseases. Drawing on expertise from a range of fields, the book offers a comprehensive review of current knowledge on vertebrate metal-withholding mechanisms and the strategies employed by different microbes to avoid starvation (or poisoning). Chapters summarize current, state-of-the-art techniques for investigating pathogen-metal interactions and highlight open question to guide future research. The book makes clear that improving knowledge in this area will be instrumental to the development of novel therapeutic measures against infectious diseases. ContributorsM. Leigh Ackland, Vahid Fa Andisi, Angele L. Arrieta, Michael A. Bachman, J. Sabine Becker, Robert E. Black, Julia Bornhorst, Sascha Brunke, Joseph A. Caruso, Jennifer S. Cavet, Anson C. K. Chan, Christopher H. Contag, Heran Darwin, George V. Dedoussis, Rodney R. Dietert, Victor J. DiRita, Carol A. Fierke, Tamara Garcia-Barrera, David P. Giedroc, Peter-Leon Hagedoorn, James A. Imlay, Marek J. Kobylarz, Joseph Lemire, Wenwen Liu, Slade A. Loutet, Wolfgang Maret, Andreas Matusch, Trevor F. Moraes, Michael E. P. Murphy, Maribel Navarro, Jerome O. Nriagu, Ana-Maria Oros-Peusquens, Elisabeth G. Pacyna, Jozef M. Pacyna, Robert D. Perry, John M. Pettifor, Stephanie Pfaffen, Dieter Rehder, Lothar Rink, Anthony B. Schryvers, Ellen K. Silbergeld, Eric P. Skaar, Miguel C. P. Soares, Kyrre Sundseth, Dennis J. Thiele, Richard B. Thompson, Meghan M. Verstraete, Gonzalo Visbal, Fudi Wang, Mian Wang, Thomas J. Webster, Jeffrey N. Weiser, Günter Weiss, Inga Wessels, Bin Ye, Judith T. Zelikoff, Lihong Zhang