Addressing retained austenite stability in advanced high strength steels

Advances in the development of new high strength steels have resulted in microstructures containing significant volume fractions of retained austenite. The transformation of retained austenite to martensite upon straining contributes towards improving the ductility. However, in order to gain from the above beneficial effect, the volume fraction, size, morphology and distribution of the retained austenite need to be controlled. In this regard, it is well known that carbon concentration in the retained austenite is responsible for its chemical stability, whereas its size and morphology determines its mechanical stability. Thus, to achieve the required mechanical properties, control of the processing parameters affecting the microstructure development is essential.

Multiscale microstructure engineering of steels

The development of modern steels is based on the tailoring of the microstructure to achieve the required properties. While historically this was performed at the micrometre scale length, there is now the scope to undertake this at the nanoscale or atom scale. The present paper reviews recent work related to the development of ultrafine and nanoscale microstructures in steel as well as changes at shorter scale lengths, such as cluster formation and solute effects. This includes the development of ultrafine ferrite through phase transformation, nanoscale and ultrafine bainite, precipitation and cluster strengthening and bake hardening of steels. A key element of the present work has been the use of atom probe tomography to unlock the nature of these structures.

Atomic scale investigation of solutes and precipitates in high strength steels

Two steels, ferritic, high strength with interphase precipitation and nano-bainitic, were used to show the advances in and application of atom probe. The coexistence of the nano-scale, interphase Nb-Mo-C clusters and stoichiometric MC nano particles was found in the high strength steel after thermomechanical processing. Moreover, the segregation of carbon at different heterogeneous sites such as grain boundary that reduces the solute element available for fine precipitation was observed. The APT study of the solutes redistribution between the retained austenite and bainitic ferrite in the nano-bainitic steel revealed: (i) the presence of two types of the retained austenite with higher and lower carbon content and (ii) segregation of carbon at the local defects such as dislocations in the bainitic ferrite during the isothermal hold.

Selective dissolution of retained austenite in nanostructured bainitic steels

Nanostructured bainitic steels, containing bainitic ferrite laths and retained austenite films, formed at two different isothermal temperatures were compared  for corrosion behavior in chloride-containing solution using electrochemical techniques. The potentiodynamic polarization results suggest that nanostructured bainite formed at 200 °C exhibits marginally higher corrosion resistance compared with that at 350 °C. Post-corrosion analysis of the galvanostatically polarized samples revealed localized corrosion for both the steels, but the degree of attack was higher in the 350 °C steel than in the 200 °C steel. The localized corrosion attack was due to selective dissolution of the retained austenite phase. The higher volume fraction and larger size of retained austenite in the 350 °C steel as compared to that of the 200 °C steel contributed to the pronounced corrosion attack in the 350 °C steel.

Experimental study into the correlation between the incremental forming and the nature of springback in automotive steels

Bending in a V-die has been well covered in the literature and the results have been used to indicate the out-come of bending in cold roll forming. However, recent work comparing springback between roll forming and single step bending has found lower springback in the roll forming process compared to single step bending. Roll forming is an incremental bending process and in this study a V-section was formed in a single operation and in multiple steps and the springback determined. The springback in V-die forming was significantly reduced by incremental forming. This suggests that the lower springback determined in roll forming compared to single step bending may be related to the incremental nature of the roll forming process.

Machinability and phase transformation study of nanobainite steels

There is an increasing demand for high strength materials with the development of technology and critical applications. Nano materials are newly developed materials with extremely high strength for this purpose. Nanobainite is a dual phase material containing alternate layers of bainitic ferrite in nano dimensions and retained austenite. Nanobainite is produced by isothermally holding austenitized steel at a temperature of 200°C or less, depending on the chemical composition, for 6 10 days until bainite forms and then cooling to room temperature using austempering. The experimental design consisted of face milling under 12 combinations of Depth of Cut (DOC)-1, 2 and 3mm; cutting speed-100 and 150m/min; constant feed-0.15mm/rev and coolant on/off. The machinability of the material is assessed by means of analysis, such as surface texture and microhardness. The assessment also involves microstructural comparisons before and after milling. Future work involves quantifying the microstructural phase before and after milling using XRD. The results obtained are used to assess the most favorable condition to cut this new variety of steel.