The effect of simulated thermomechanical processing on the transformation behavior and microstructure of a low-carbon Mo-Nb linepipe steel

The present work investigates the transformation behavior of a low-carbon Mo-Nb linepipe steel and the corresponding transformation product microstructures using deformation dilatometry. The continuous cooling transformation (CCT) diagrams have been constructed for both the fully recrystallized austenite and that deformed in uniaxial compression at 1148 K (875 °C) to a strain of 0.5 for cooling rates ranging from 0.1 to about 100 K/s. The obtained microstructures have been studied in detail using electron backscattered diffraction complemented by transmission electron microscopy. Heavy deformation of the parent austenite has caused a significant expansion of the polygonal ferrite transformation field in the CCT diagram, as well as a shift in the non-equilibrium ferrite transformation fields toward higher cooling rates. Furthermore, the austenite deformation has resulted in a pronounced refinement in both the effective grain (sheaf/packet) size and substructure unit size of the non-equilibrium ferrite microstructures. The optimum microstructure expected to display an excellent balance between strength and toughness is a mix of quasi-polygonal ferrite and granular bainite (often termed “acicular ferrite”) produced from the heavily deformed austenite within a processing window covering the cooling rates from about 10 to about 100 K/s.

Investigation of corrosion inhibition mechanisms of rare-earth mercaptoacetate inhibitors on AA2024-T3

 Corrosion inhibition mechanisms on the aerospace alloy, AA2024-T3, was investigated for the inhibitor combination of rare earth metals and mercaptoacetate. The inhibitor demonstrated synergistic protection for AA2024-T3 from localised corrosion. It is intended to be a more environmentally friendly alternative to toxic chromate-based inhibitors.

Microstructure and texture evolution during tensile deformation of symmetric/asymmetric-rolled low carbon microalloyed steel

The deformation and fracture mechanisms of a low carbon microalloyed steel processed by asymmetric rolling (AsR) and symmetric rolling (SR) were compared by microstructural and texture evolutions during uniaxial tensile deformation. A realistic microstructure-based micromechanical modeling was involved as well. AsR provides more effective grain refinement and beneficial shear textures, leading to higher ductility and extraordinary strain hardening with improved yield and ultimate tensile stresses as well as promoting the occurrence of ductile fracture. This was verified and further explained by means of the different fracture modes during quasi-static uniaxial deformation, the preferred void nucleation sites and crack propagation behavior, and the change in the dislocation density based on the kernel average misorientation (KAM) distribution. The equivalent strain/stress partitioning during tensile deformation of AsR and SR specimens was modeled based on a two-dimensional (2D) representative volume element (RVE) approach. The trend of strain/stress partitioning in the ferrite matrix agrees well with the experimental results.

Imidazolinium inhibitor for mild steel in aggressive conditions

An organic salt comprising of an imidazolinium cation and a 4-hydroxy cinnamate anion has been shown to be a viable inhibitor for reducing the corrosion of steel in 0.01M NaCl aqueous solutions under acidic, neutral and basic conditions. The efficiency is particularly high at pH 8 (86%). Of most significance is that the individual components of this compound do not inhibit as effectively at equivalent concentrations, particularly at a pH of 2, suggesting there is a true synergy resulting from the combination of anion and cation. The immersion studies show the efficacy of these inhibitors to stifle corrosion as observed from optical, SEM and profilometry experiments. The mechanism of inhibition appears to be dominated by anodic behavior and further surface characterization work will investigate the origin of this inhibition and the synergy observed.

Microstructure and hardness evolution during simulated coiling of a direct strip cast low carbon low niobium steel

This paper examines the impact of coiling temperature and duration on the phase transformation and precipitation behavior of a low carbon and low niobium direct strip cast steel. Coiling was performed at three carefully chosen temperatures: (1) in the ferrite (600°C), (2) during the austenite decomposition (700°C) and (3) in the austenite (850°C). The coiling conditions were found to strongly affect the final microstructure and hardness response, thus highlighting the necessity to judiciously design the coiling treatment. Optical microscopy, and scanning and transmission electron microscopy were used to characterize the microstructural constituents (polygonal ferrite, bainite and pearlite) and the NbC precipitates. Vickers macrohardness measurements are utilized to quantify the mechanical properties. The differences in hardening kinetics for the three different temperatures are shown to come from a complex combination of strengthening contributions.

Occurrence of anodic current and corrosion of steel in aqueous media under fluctuating cathodic protection potentials

Excursion of cathodic protection (CP) potential from the designed "safe" CP level resulting from various forms of electrical interference signals are observed rather frequently in industrial applications, in particular in the pipeline industry; however, the influence of such potential fluctuations on the corrosion behavior of steel under CP conditions does not yet appear to be fully understood. In this work, the effects of anodic transients that periodically shift the potential of a CP protected steel electrode from-1,200 mVAg/AgCl to-750 mVAg/AgCl on the corrosion of a steel electrode in aqueous media was investigated using square wave polarization. Anodic currents were measured that lasted for significant periods of time upon stepping the CP potential up to a less cathodic potential at various frequencies (1 h, 30 s, 10 s, 5 s, and 1 s). Part of such anodic currents is found to cause steel corrosion, and this is explained on the basis of understanding the Fe/H2O equilibrium.

Growth of bainitic ferrite and carbon partitioning during the early stages of bainite transformation in a 2 mass% silicon steel studied by in situ neutron diffraction, TEM and APT

In situ neutron diffraction, transmission electron microscopy (TEM) and atom probe tomography (APT) have been used to study the early stages of bainite transformation in a 2 mass% Si nano-bainitic steel. It was observed that carbon redistribution between the bainitic ferrite and retained austenite at the early stages of the bainite transformation at low isothermal holding occurred in the following sequence: (i) formation of bainitic ferrite nuclei within carbon-depleted regions immediately after the beginning of isothermal treatment; (ii) carbon partitioning immediately after the formation of bainitic ferrite nuclei but substantial carbon diffusion only after 33 min of bainite isothermal holding; (iii) formation of the carbon-enriched remaining austenite in the vicinity of bainitic laths at the beginning of the transformation; (iv) segregation of carbon to the dislocations near the austenite/ferrite interface; and (v) homogeneous redistribution of carbon within the remaining austenite with the progress of the transformation and with the formation of bainitic ferrite colonies. Bainitic ferrite nucleated at internal defects or bainite/austenite interfaces as well as at the prior austenite grain boundary. Bainitic ferrite has been observed in the form of an individual layer, a colony of layers and a layer with sideplates at the early stages of transformation.

EBSD and AFM observations of the microstructural changes induced by low temperature plasma carburising on AISI 316

Low temperature plasma carburising (LTPC) has been increasingly accepted as a hardening process for austenitic stainless steels because it produces a good combination of tribological and corrosion properties. The hardening mechanism is based on the supersaturation of the austenitic structure with carbon, which greatly hardens the material, significantly expands the fcc unit cell, produces high levels of compressive residual stresses and, ultimately, leads to the occurrence of deformation bands and rotation of the crystal lattice. The microstructural changes introduced during plasma carburising have a significant impact on the mechanical, tribological and corrosion performance and, for this reason, the microstructure of expanded austenite or S-phase has been extensively studied. However, modern surface characterisation techniques could provide new insights into the formation mechanism of S-phase layers. In this work, backscattered electron diffraction and atomic force microscopy were used to characterise the surface layers of expanded austenite produced by LTPC in an active screen furnace. Based on the experimental results, the plastic deformation, its dependence on crystallographic orientation, the evolution of grain boundaries, and their effects on mechanical, tribological and corrosion properties are discussed. © 2011 Elsevier B.V. All rights reserved.

The influence of solute carbon in cold-rolled steels on shear band formation and recrystallization texture

Two experiments were conducted to clarify the roles of grain size, solute carbon and strain in determining the recrystallization textures of cold-rolled and annealed steels. In the first experiment, samples of coarse-grained low-carbon (LC) and interstitial-free (IF) steels were cold-rolled to a 75% reduction in thickness. One sample from each steel was polished and cold-rolled an additional 5%, while the remaining samples were annealed for various times at 650°C. In the second experiment, three samples from a commercial LC steel sheet were rolled 70% at 300°C. Two of the samples were given a further rolling reduction of 5% of the original thickness, with one of the samples being given this additional reduction at 300°C and the other at room temperature. Goss recrystallization textures are strengthened by coarse initial grain sizes, the presence of solute carbon and rolling at a temperature where dynamic strain ageing occurs, but are weakened by additional rolling beyond a reduction of 70%, especially when this extra rolling is conducted at a temperature where dynamic strain ageing does not occur. Characterization of key features of the deformed and recrystallized steels using optical microscopy, scanning electron microscopy (SEM) and electron back-scatter diffraction (EBSD) supports a rationale for these effects based on the repeated activation and deactivation of shear bands and the influence of solute carbon and dynamic strain ageing on the operating life of the bands and the accumulation of strain within them.

The determination of urea in soil extracts and related samples - a review

Although the dominant methods for the determination of urea in clinical applications incorporate selective enzymatic hydrolysis of urea, the determination of urea in soil extracts is complicated by the presence of urease inhibitors. The spectrophotometric determination of urea with an acidic solution diacetyl monoxime and semicarbazide is a viable option but traditional manual procedures are time-consuming. New variations on these procedures, based on microplates or flow-injection analysis methodologies, allow a far greater number of samples to be analysed with high precision and sensitivity.