27 resultados para Portland cement.
Resumo:
Abstract: In this experimental study, the reinforcing effects of graphene oxide (GO) on portland cement paste are investigated. It is discovered that the introduction of 0.03% by weight GO sheets into the cement paste can increase the compressive strength and tensile strength of the cement composite by more than 40% due to the reduction of the pore structure of the cement paste. Moreover, the inclusion of the GO sheets enhances the degree of hydration of the cement paste. However, the workability of the GO-cement composite becomes somewhat reduced. The overall results indicate that GO could be a promising nanofillers for reinforcing the engineering properties of portland cement paste.
Resumo:
Carbon nanotubes (CNTs) are among the strongest known materials. Their potential as nanoscale reinforcement for cementitious materials is significant, with some reported compressive strength increases in excess of 50%. However, there is a great deal of variability in the results obtained, with some researchers showing zero-to-marginal increases in mechanical properties. One major reason for this is the poor dispersion of CNTs within the cementitious matrix. Many different approaches have been employed to disperse the highly hydrophobic CNTs within water and cement paste, with varying degrees of success. This paper presents the results of dispersion trials undertaken on CNTs within neutral and alkaline aqueous solutions and assesses the relative performance of different surfactants to facilitate dispersion.
Resumo:
Significant research advances have been made in the field of carbon nanotube (CNT) reinforced ordinary Portland cement (OPC) paste composites in recent years. However, the distribution of CNTs in fresh OPC paste is yet to be fully researched and quantified, thereby creating a technical barrier to CNT utilization in concrete construction. In this study, fresh OPC paste was treated as a two-phase material containing solid particles (cement grains) and liquid solutions (pore solutions). A centrifugation-based technique was proposed to separate these two phases and the presence of CNTs in each phase was quantified. UV-Vis spectrometry showed that the degree of dispersion can achieve above 90 wt% using polycarboxylate superplasticizer. The results suggested an upper limit of 0.26 wt% for CNT addition into water before mixing with OPC, and the dispersion was found to be stable for at least 4 hours. Based on scanning electron imaging, the adsorption phenomenon of CNTs on OPC grains with size less than 4 μm was discovered. Energy-dispersive X-ray spectroscopy indicated these adsorptive particles have lower Ca to Si ratio. It was observed that about 0.5 mg of CNTs per gram of OPC grains was adsorbed in solid OPC grains in typical fresh OPC pastes. On the basis of these results, a conceptual model was proposed for the distribution of CNTs in fresh OPC paste where about 33 wt% of the CNTs stay in pore solution and 65 wt% of CNTs are adsorbed on OPC grains.
Resumo:
The thesis examines sources of economies of scale for the manufacture and distribution of Portland cement. Using cost models, it is shown that recent advances in technology have increased the economies of scale for efficient clinker production significantly, and to a lesser degree for finish grinding operations and bulk distribution.
Resumo:
This journal is © The Royal Society of Chemistry. A novel self-adapting retarder itaconic acid/acrylamide/sodium styrene sulfonate (IA/AM/SSS, hereinafter referred to as PIAS) was synthesized by free-radical, aqueous-solution polymerization and characterized by FTIR and TG. The optimum reaction conditions of polymerization were obtained from orthogonal experiments (L33) and subsequent data analysis. According to the evaluation as a retarder, the PIAS made it possible to obtain both a long thickening time and a swift compressive strength development for cement slurry, and therefore the applicable range of bottom hole circulation temperatures to the cement slurry has been widened to 60-180°C. Moreover, the working mechanism of the self-adapting retarder PIAS was found to rely on the change of spatial structure of the molecules to retard the hydration of the cement. This paper also expounds that the delayed coagulation of the cement slurry is attributed to adsorption, chelation and "poisoning" effects of the PIAS molecules on the surface of hydrated particles or ions through XRD and SEM analyses.
Resumo:
Using cement-based material as a matrix for photocatalytic hybrids is an important development for the large-scale application of photocatalytic technologies. In this work, photocatalytic activity of nanosized hybrids of TiO2/SiO2 (nano-TiO2-SiO2) for degradation of some organic dyes on cementitious materials was highlighted. For this purpose, an optimal inorganic sol-gel precursor was firstly applied to prepare the composites of nano-TiO2-SiO2 which was characterized by XRD, SEM and UV-Vis. Then, a thin layer was successfully coated on white Portland cement (WPC) blocks using a dipping process in a nano-TiO2-SiO2 solution. The effect of nano-TiO2-SiO2-coated WPC blocks on photocatalytic decomposition of three dyes, including Malachite green oxalate (MG), Methylene blue (MB) and Methyl orange (MO) were studied under UV irradiation and monitored by chemical oxygen demand tests. The results showed an increase in photocatalytic effects which depends on the structure and pH of the applied cement.
Resumo:
This paper reports on the second phase of a research project aimed at the development of an environmentally friendly noise barrier for urban freeways, also known as KMAK (Krezel and McManus, 2007). The concrete barrier, which has some unique capabilities to mitigate transportation noise, is made from recycled concrete (RC) aggregate and industrial by-products such as fly ash and reclaimed water. The current developmental work expands on a research project that resulted in a two-layer (2L) concrete barrier. Two prototypes of the 2L barrier were produced, followed by extensive acoustic testing and a number of simulations where standard timber and/or concrete barriers were substituted with KMAK barrier (Krezel et al, 2004). Current research investigates a variety of architectural finishes applied to the original KMAK barrier with the aim of improving its visual appearance and also fine-tuning its acoustic performance. The new three-layer (3L) barrier optimises sound absorption in a frequency range characteristic to that of transportation noise, especially road traffic noise. Three major aspects related to the development of architectural finishes were considered; environmentally responsible materials, surface features and production methods. The light-weight material used in the architectural finish is based on ordinary Portland cement (OPC) and uses very fine fraction of RC aggregate. The manufacturing process of the 3L barrier was tested in a commercial setting and two sets of prototype barrier were cast. An innovative, cost effective method of applying pattern and perforation to the surface of architectural finish was also developed and tested. The findings of the current investigation demonstrate that there is a positive correlation between surface features, percentage of perforation as well as depth of the architectural layer and increased potential of the 3L barrier to mitigate transportation noise. On average, the addition of perforated architectural finish contributes to 20% increase in sound absorption. The preliminary results also show that the sound absorbency of the 3L barrier can be better controlled and tuned to specific noise frequency. The visual appearance has been significantly improved with the addition of the architectural finish, which makes the barrier an attractive, feasible and viable alternative to road barriers made from standard concrete or timber.
Resumo:
Knowledge of the degree of hydration of cement pastes is critical for determining properties such as the durability of concrete. As part of an integrated study on the prediction of chloride ingress in reinforced concrete, synchrotron Xray powder diffraction was used to estimate the degree of hydration of cement pastes. While for the past 20 years the composition of Portland cement has been determined by Rietveld analysis of X-ray diffraction, nevertheless there are a number of factors, including the amorphous content of the cement and relative proportion of mineral polymorphs present in the initial clinker, whose impact on the analysis are still not completely understood. Analysis of the resulting diffraction patterns indicated enhanced identification of polymorphs of alite, belite, ferrite and aluminate, which are present in the initial unhydrated cement and clinker, as well as improved quantification of hydrated crystalline phases such as calcium hydroxide and ettringite, which are key phases determining the speed of the chemical reactions in cement. In this paper we describe the experience that we have gained in the determination of the degree of hydration of cement pastes. We detail the standards and precautions that we took to characterize production cements and their hydration products.
Resumo:
The effects of strain rate on compressive and tensile strength of fly ash based geopolymer concrete were investigated experimentally. Four mixes of geopolymer concrete using different alkaline solutions and under vary curing conditions were prepared. One mix of ordinary Portland cement (OPC) concrete was prepared for comparison. Both Quasi-Static tests using standard MTS and dynamic tests using Split-Hopkinson pressures bar (SHPB) were conducted, which were giving varying strain rate loadings from 10‾⁷ to 103 per second. The strain rate effect is presented as the ratio of dynamic compressive strength to static compressive strength (DIF). Results show that DIFs of geopolymer concrete are generally higher than those of OPC concrete at strain range of 187/s to 346/s (compression tests) and 7/s to 13/s (splitting tensile tests), respectively. This tendency is independent on loading regimes (compression or tension). This suggests that geopolymer concrete can be used as an alternative construction material to OPC concrete for the structures which has a high risk of being subjected to impact loadings.
Resumo:
As environmentally-friendly materials, geopolymers have the potential to replace ordinary Portland cement (OPC) for the construction of railway sleepers and multi-flue chimneys, where the vibration control capabilities of the material must be considered. The critical damping value (ξ) is the main parameter in relation to vibration reduction. In this study, the traditional logarithmic decrement technique was used to measure the ξ of geopolymers. Geopolymers were prepared by activating fly ash using alkali solutions with different SiO2/Na2O ratios. The results show that the ξ of the geopolymers is similar to that of the OPC counterpart. Finite element analysis (FEM) based on the Rayleigh damping model was conducted to replicate the test results, and scanning electron microscopy and mercury-intrusion porosimetry were used to study the microstructure of the geopolymers. A discussion of the possible damping mechanisms based on the microstructural investigation and the FEM analysis is presented.
Free and restrained shrinkage behaviours of OPC and slag concretes with admixed polypropylene fibres
Resumo:
This paper presents the results of an investigation that studied the effects of admixed polypropylene (PP) fibres on the long-term drying shrinkage of hardened concrete. Five concrete mixtures, made with 100% Ordinary Portland Cement (OPC) as the binder and containing different volume fractions of PP fibre (0%, 0.05%, 0.1%, 0.2% and 0.5%) were tested. Also, three concrete mixtures were made with 65 % slag-blended cement binder incorporating 0% and 0.2% volume fraction of PP. The results show higher water loss and higher drying shrinkages in concretes that incorporate PP fibres than concrete without fibre. The results of early age cracking tendency of slag concrete, with and without fibre, under fully restrained and drying conditions, show that that PP fibre concrete had higher cracking tendency than concrete without fibre. Higher cracking tendency of PP fibre concrete was due to higher drying shrinkage and elastic moduli.
Resumo:
The construction of evaporative ponds and wetlands for the disposal of waste water high in ionic concentrations is a waste disposal strategy currently considered by many industries. However, the design, construction and management of these ponds and wetlands are not straightforward as complex chemical interactions result in both spatial and temporal changes in water quality. The effects of evaporation and drainage on the water quality in two constructed ponds, an adjacent man-made wetland and local groundwater at Portland Aluminium were investigated. The minimum volume of water entering the ponds during the study period was 0.96±0.16 ML per month. The predicted theoretical evaporative capacity of the two ponds was calculated to be 0.30±0.07 ML per month. More water enters the ponds than it is theoretically possible to evaporate under the ambient weather conditions at Portland, yet the ponds do not overflow, suggesting percolation through the pond lining. No spatial differences in solute concentrations (fluoride, sulphate, bicarbonate, carbonate, sodium, potassium, calcium, and magnesium ions) were found within the waters of either pond, although temporal differences were apparent. The results support the conclusion that the ponds are not impermeable, and that much of the waste water entering the ponds is being lost through seepage. The impacts on local groundwater chemistry of this seepage are addressed. Significant correlations exist between solute presence within and between the ponds, wetland and groundwater. Fluoride and sulphate concentrations were significantly higher in pond waters throughout the duration of the experiment. Pond sediments revealed a high degree of spatial and temporal heterogeneity in the concentration of all monitored ions resulting from the chemical heterogeneity of the material making up the pond linings. Adsorption isotherms for fluoride indicate that the adsorption capacity of the pond linings remains high for this ion. Implications for the management of waste water by this strategy are discussed.